丝状菌对生物淋滤去除底泥中重金属的促进作用

利用氧化亚铁硫杆菌(Acidithiobacillus ferrooxidans,A.f)对采自株洲霞湾港底泥中的Cu、Cd、Pb和Zn 4种重金属进行生物淋滤实验,在实验中加入丝状菌考察其对重金属去除效果的影响。结果表明,丝状菌可以有效抑制低分子量有机酸对A.f的毒害作用,促进各种重金属的去除。当加入10%(体积比)的丝状菌后,生物淋滤过程中系统pH值在5 d内降低到2以下,Fe2+在4 d内完全氧化。经过10 d的处理,Cu、Cd、Pb和Zn 4种重金属的最高去除率分别达到76.3%、92.5%、52.6%和88.5%,与不加入丝状菌的处理相比,达到最大去除率所需的时间缩短1~2 d,4种重金属中,丝状菌的加入对Pb的去除促进作用最为明显,其去除率增加1倍左右。因此,在生物淋滤处理重金属-有机物复合污染底泥工艺中接入丝状菌对处理效果有很好的促进作用。     

生物淋滤对城市污泥重金属去除及形态变化的影响研究

以氧化亚铁硫杆菌(Acidithiobacillus ferrooxidans)为淋滤菌,对城市污泥进行生物淋滤,考察淋滤过程中污泥重金属(Cu、Zn、Ni、Cr)的去除及其形态变化规律,并根据淋滤前后重金属形态分布探讨重金属的淋滤去除机制。结果表明,生物淋滤可有效去除城市污泥中的Cu、Zn和Ni,对Cr几乎没有去除。生物淋滤后,Cu、Zn、Ni、Cr 4种重金属的去除率分别为55.97%、47.66%、26.10%、2.10%。pH是影响Zn和Ni去除的主要因素,而Cu在低pH和高氧化还原电位(ORP)条件下更易去除。BCR形态分析表明,生物淋滤之后污泥中Cu、Zn和Ni的4种形态含量均发生了不同程度的改变,其生物有效性和迁移性得到有效控制。通过重金属形态变化规律间接得出,Cu的生物淋滤过程以直接机制为主,Zn和Ni的生物淋滤过程是直接机制和间接机制共同作用的结果。     

生物淋滤技术对城市污泥中高浓度重金属的去除

实验以单质硫粉作为能源基质,考查了生物淋滤技术针对城市污泥中高浓度重金属的去除效果,探讨了生物淋滤处置前后污泥中重金属的形态变化规律。结果表明,生物淋滤技术能够有效去除污泥中的高浓度重金属。在硫粉投加量为4 g·L~(-1)、HRT为5 d、污泥回流比为50%、污泥浓度为4%、温度为30℃的条件下,生物淋滤系统pH值可降低至1.5左右,污泥中残留重金属Zn、Cu、Cr、Ni分别可降低至400、400、900和200 mg·kg~(-1)左右,达到了《城镇污水处理厂污泥处置林地用泥质》(CJ/T 362~(-2)011)标准重金属限值。生物淋滤处置后,污泥中残留重金属Zn、Cu、Cr、Ni均主要以稳定形态存在,环境风险较低,为进行土地利用奠定了物质基础。     

3种修复剂对底泥中不同形态重金属去除效果评估

随着经济发展,越来越多的重金属通过各种途径进入水体,其中部分通过物理、化学或生物作用在底泥中沉积。在合适条件下,底泥中的重金属又会重新进入水体,危害水生生物以及人类健康。沸石粉、生物炭和镉康等材料常常被应用于底泥中重金属的修复,使重金属中能被生物利用的形态转化为残渣态。通过比较沸石粉、生物炭和镉康对底泥中非残渣态的Cu、As、Cd和Pb的去除效率,发现这3种修复剂均有一定的去除效果,其中沸石粉及生物炭对底泥中非残渣态的重金属去除效果较好。总体来讲,这3种用于底泥非残渣态重金属去除的修复剂的性价比表现为:沸石粉生物炭镉康。     

基于生物淋滤的城市污泥重金属溶出及形态迁移

利用生物淋滤法处理城市污泥,以生物淋滤过程中pH、ORP(氧化还原电位)变化以及重金属(Zn、Cu、Cd)溶出率为指标,考察淋滤菌接种比例、初始pH、淋滤时间对生物淋滤的影响,并分析了生物淋滤前后,重金属形态变化以及重金属的生物有效性和迁移性。结果表明富集筛选的嗜酸性氧化亚铁硫杆菌(A.f)可有效溶出污泥中的重金属。生物淋滤最佳条件为:初始pH=4.00,淋滤菌接种比例30%,重金属Zn,Cu,Cd在第10天的整体处理效果最优,溶出率分别达到75.30%、50.40%和74.44%。BCR形态分析表明:原污泥中Zn,Cu,Cd主要以弱酸提取态、可还原态和氧化态存在,残渣态较少;生物淋滤之后,3种重金属弱酸提取态、可还原态和氧化态含量有不同程度降低,其中,可还原态含量降低最为显著,残渣态基本无变化,并且淋滤后污泥中重金属氧化态及残渣态所占比例较淋滤前高,污泥稳定性得到提升。生物淋滤可以通过减少污泥中重金属含量和改变重金属形态降低其生物有效性和迁移性。     

Fenton预处理对城市污泥重金属形态及生物淋滤溶出影响

针对生物淋滤处理城市污泥重金属Cr、As和Pd的溶出效率较低的问题,采用芬顿(Fenton)氧化法对城市污泥进行预处理,考察Fenton氧化对污泥中重金属Cr、As和Pd赋存形态转化及后继生物淋滤过程溶出率的影响。实验结果表明,经pH=4.00、Fe~(2+)=1.00 g·L~(-1)、H_2O_2=9 g·L~(-1)的条件下Fenton预处理后,重金属Cr、As和Pb的存在形态均由稳定性较强的可氧化态和残渣态向不稳定的弱酸提取态和可还原态转化,其不稳定态比重分别由15%、30%、9%提高到了24%、41%、11%;生物淋滤实验结果显示,由于重金属形态变化,重金属Cr、As和Pb溶出率分别由52.71%、11.15%、33.19%提升至60.76%、24.32%、45.96%。Fenton预处理联合生物淋滤法提高了对重金属Cr、As和Pb的去除效果,有助于实现污泥的无害化处理处置。     

生物沥滤去除污泥、土壤和底泥中3种重金属比较研究

以硫酸亚铁为底物,对城市污泥、土壤和河流底泥进行生物沥滤实验,探讨了污泥、底泥和土壤在沥滤过程中重金属的去除效果和化学形态转化规律,了解当地土壤在酸化条件下重金属的释放过程,并对三者的研究结果进行比较分析。结果表明,污泥生物沥滤对重金属(Zn、Cu和Pb)的沥滤的沥滤效果较佳(去除率75.45%、63.12%和40.96%)。沥滤过程中,重金属Cu在生物沥滤中期(3~5 d)沥出效果较好,而Zn和Pb则在沥滤后期(5~9 d)。同一重金属在不同沥滤体系中的形态变化过程差异较大,沥滤后的污泥、土壤和底泥中的重金属大部分呈现稳定状态。     

撒施阻控材料快速去除上覆水Cd对的室内模拟研究

湘中矿区塘、水库等灌溉水体及其底泥重金属超标问题日益凸显,研究选取石灰、水稻秸秆生物炭和人造沸石等3种环境友好型土壤重金属阻控材料,通过室内玻璃柱模拟静止水体实验探讨水面缓慢撒施阻控材料对上覆水重金属Cd去除与底泥Cd有效性影响。为期60 d的实验结果显示,1%(0~20 cm表层底泥质量分数)的单一石灰、生物炭、沸石与石灰+生物炭+人造沸石配方(质量比1∶1∶1)4种处理均可明显快速去除上覆水中水溶态Cd质量浓度,其中石灰效果最佳,沸石效果最差,石灰与3种阻控剂组配处理均可使上覆水中水溶态Cd质量浓度由20μg·L~(-1)以上降至10μg·L~(-1),符合我国灌溉水Cd的限定标准。阻控材料自然沉积在底泥表面后对5 cm处底泥水溶液Cd质量浓度具有一定的消减效应,沸石效果优于石灰、生物炭处理,其中"石灰+生物炭+沸石"的不同粒径阻控材料组配方式效果最佳。石灰、生物炭、沸石及3种阻控剂组配处理60 d后底泥pH值依然略高于对照,差异不显著,但可交换态Cd含量明显低于对照。结果可为塘库型水体上覆水及底泥Cd等重金属污染的生态风险降低及控制措施研究提供科学参考与方法指导。     

不同化学淋洗剂对复合重金属污染土壤的修复机理

化学淋洗技术是一种常用的重金属污染土壤修复技术,化学淋洗剂的选择尤为重要。以乙二胺四乙酸二钠(EDTA),柠檬酸(CA)和三氯化铁(FeCl_3)为化学淋洗剂,采用振荡淋洗法研究淋洗时间与淋洗剂浓度对Cu、Zn、Pb和Cd去除效果的影响,分析重金属污染土壤淋洗前后重金属形态与基本理化性质的变化。结果表明:3种化学淋洗剂对重金属的快速反应阶段基本在60 min内,在240 min达到淋洗平衡,对Pb和Cd的淋洗主要是非均相扩散过程;EDTA、柠檬酸和FeCl_3对重金属的去除能力依次为PbCdCuZn,CdZnCuPb与Pb≈CdCuZn,EDTA的淋洗效率最高,Cd的解吸能力最强;EDTA和FeCl_3可有效去除弱酸可溶态与可还原态重金属,柠檬酸能有效去除弱酸可溶态重金属,修复后的土壤仍有环境风险;3种淋洗剂修复后的土壤中总有机碳与粒径分布无明显变化,FeCl_3会酸化土壤。综合考虑,EDTA、柠檬酸和FeCl_3均为淋洗效果好的环境友好型化学淋洗剂,该研究成果可用于现场淋洗去除土壤中重金属的小试。     

氧化亚铁硫杆菌对电子垃圾焚烧迹地重金属形态的影响简

采用生物淋滤法处理电子垃圾焚烧迹地重金属严重污染的土壤。所用氧化亚铁硫杆菌是从矿坑废水中通过一系列培养、分离和纯化得到。实验结果表明，生物淋滤法可以有效地去除土壤中重金属Cu、Pb和Zn，去除率的大小顺序为Zn>Cu>Pb；采用五步连续提取法分析处理前后土壤中重金属的存在形态，结果表明，通过氧化亚铁硫杆菌处理受重金属污染的土壤，可以促使易移动的重金属结合态的溶解（可交换态、碳酸盐结合态和Fe-Mn氧化物结合态），并使难移动的重金属结合态向易移动的重金属结合态转变。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的策划

在实施ISO／IEC 17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核策划阶段的关键环节，提出审核范围确定、审核计划和抽样方案制订的质量控制要求，为有序高效地实施内部审核提供了技术方法。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.