处理垃圾渗滤液的反渗透膜污染研究

膜污染及其防治是影响膜系统运行效果的重要因素。本研究选取工程中运行一年多的处理垃圾渗滤液的碟管式反渗透膜，经研究判断，污染絮体的主要成分是有机物，并含有Al、Si等的胶体物质以及Fe和Ca的化合物。通过化学清洗来验证对污染层结构的判断，先碱洗后酸洗的清洗效果远远好于先酸洗后碱洗，有机物在污染层形成过程中起主要作用，减少渗滤液中的有机物质，将会大大减轻膜污染的发生。     

内置转盘式PVDF膜生物反应器污水处理的试验研究

对内置转盘式PVDF膜生物反应器(SRMBR)处理污水工艺及膜清洗进行了研究.SRMBR处理污水可以长期稳定运行,在实验模拟污水COD为180～368 mg/L时,出水COD在运行1d后稳定在20 mg/L以内,COD去除率>93%.增大转盘式平板膜组件转速可以增大SRMBR的平衡水通量,转速从15 r/min增大到25 r/min,平衡水通量从42.5 L/(m2·h)增大到47.5L/(m2·h).在一定自吸泵停抽时间内(0～1 min),延长停抽时间有利于减缓膜污染、提高平衡水通量.对污染的膜进行水洗、水洗 碱洗、水洗 碱洗 酸洗,3种清洗方式分别使膜平衡水通量恢复至新膜平衡水通量的48.4%、83.5%、90.2%.     

膜生物反应器中膜的清洗方法和机理研究

研究了膜生物反应器处理盥洗废水时 ,水力清洗、酸洗、碱洗等不同组合形式对膜的清洗效果。结果表明 ,水力清洗可以较彻底地去除运行初期的膜表面沉积物 ,使膜通量有较大程度的恢复。对运行时间较长的膜来说 ,有机物和微生物是造成膜污染的主要原因。清水冲洗后用 0 0 5 %NaClO浸泡 1h ,再用 0 5 %的H2 SO4浸泡 1h是盥洗废水处理用膜有效的清洗方法 ,清水膜通量可恢复至 1 0 0 %。     

膜生物反应器中膜的清洗方法和机理研究

研究了膜生物反应器处理盥洗废水时，水力清洗、酸洗、碱洗等不同组合形式对膜的清洗效果。结果表明，水力清洗可以较彻底地去除运行初期的膜表面沉积物，使膜通量有较大程度的恢复。对运行时间较长的膜来说，有机物和微生物是造成膜污染的主要原因。清水冲洗后用0．05％ NaClO浸泡1h，再用0．5％的H2SO4浸泡1h是盥洗废水处理用膜有效的清洗方法，清水膜通量可恢复至100％。     

印染废水回用微滤膜污染控制研究

采用PVDF中空纤维微滤膜处理某纺织印染厂二级生化出水,研究了膜污染控制及清洗方法。结果表明,合理的膜通量是控制膜污染、保证膜寿命的关键,采用31 L/(m2.h)左右的通量有助于膜污染的控制。氢氧化钠与次氯酸钠可分别用于日常维护清洗与恢复清洗,通过循环正洗不仅能满足清洗要求,且药剂使用量也小于反洗方法,每吨产水清洗用碱费用仅0.06元。化学清洗后再水力正洗,能进一步提高清洗效果。     

电絮凝延缓陶瓷微滤膜污染

为提高陶瓷微滤膜净化微污染水源水时的产水量,采用电絮凝预处理工艺延缓陶瓷膜的污染。研究了电流密度、进水流量以及跨膜压差对组合工艺产水量的影响,结果显示,较之原水直接微滤,电絮凝预处理后膜产水量得到提升。其最佳运行参数为:电流密度1.5 m A/cm2,进水流量3 L/min,跨膜压差0.15 MPa。同时,比较了碱型、氧化型和配位型药剂清洗对膜污染的影响,结果表明,先用氧化型药剂清洗,再用配位型药剂清洗的方式膜通量恢复值最高。     

改性PES膜在MBR中膜阻力分析及膜污染机理研究

以聚醚砜(PES)、醋酸纤维素(CA)和纳米二氧化钛(TiO2)为膜材料,采用L-S相转化法制备共混改性PES膜。在24℃、0.2 MPa的操作条件下,制得的PES膜纯水通量为300 L/(m2.h)左右,CA改性PES膜为660 L/(m2.h)左右,TiO2改性PES膜为840 L/(m2.h)左右。通过膜生物反应器中膜阻力的测定,表明膜污染主要由浓差极化层及凝胶层引起的;通过活性污泥对膜污染机理的研究,判断出污泥的过滤过程基本符合沉积过滤定律。在MBR中运行时,改性PES膜稳定通量高于未改性膜,总阻力低于未改性膜;TiO2改性膜稳定通量高于CA改性膜,总阻力低于CA改性膜;通过扫描电镜分析,改性PES膜沉积层的厚度均比未改性膜薄,TiO2改性膜沉积层厚度小于CA改性膜,表明改性膜的抗污染性能提高了,TiO改性膜抗污染性能更优。     

应用于维生素C凝结水处理反渗透膜清洗策略

针对沈阳某药厂维生素C生产工艺中凝结水产量大、处理成本高和杂质复杂等问题,提出了采用反渗透技术对工艺凝结水进行处理。在前期确定的最优操作条件基础上持续运行,研究了运行临界通量、清洗时机和清洗方式等工艺条件。结果表明,在本工艺条件下,反渗透膜系统的临界通量介于1.1 L/(m2.min)到1.2 L/(m2.min)之间,斜率变点分析法确定的可逆膜污染周期为10 d;加强型清洗策略EFM(enhanced flux maintenance)的操作是针对不可逆膜污染的一种有效清洗方式,EFM持续30 min为宜,NaClO和NaOH都是有机污染的有效清洗剂,膜的平均恢复率分别为85.4%和81.6%,显示出实际应用的可行性,具有推广价值。     

厌氧膜生物反应器处理酒厂废水运行特性研究

在一体式平板厌氧膜生物反应器处理酒厂废水的试验中,研究了污染物的去除效果和平板膜组件的运行、污染情况.试验结果表明,COD容积负荷为3～7 kg/(m3·d)、水力停留时间(HRT)为16 h时,平均COD去除率达94.2%;在膜通量为4.6 L/(m2·h)、上升流速为2.5 m/h的条件下,平板膜组件能够连续运行18～20 d;在该试验中临界通量和临界上升流速分别为10～15 L/(m2·h)和5.0m/h,平板膜组件应该在这两个临界值之下运行.膜过滤阻力分析测试结果表明,泥饼层阻力是总阻力的最大组成部分.     

MBR的临界膜通量及其影响研究

采用通量阶梯式递增法测定了MBR的临界膜通量，研究了膜面气液两相流流速对临界膜通量影响，并考察次临界膜通量下MBR处理垃圾渗滤液的运行特性。试验结果表明，膜面气液两相流流速对临界膜通量影响较大，膜面气液两相流流速由0.9 m/s增至1.8 m/s，临界膜通量由12～14 L/(m²·h)增加至16～18 L/(m²·h)，两者呈显著正相关关系，相关系数为0.997。次临界膜通量下运行时，膜污染包括不可逆污染和可逆污染2个阶段：不可逆污染阶段以凝胶层污染为主，占总量的72%，而可逆污染阶段以滤饼层形成的阻力为主，占总阻力的68.5%。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

实验室质量管理体系内部审核的策划

在实施ISO／IEC 17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核策划阶段的关键环节，提出审核范围确定、审核计划和抽样方案制订的质量控制要求，为有序高效地实施内部审核提供了技术方法。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.