餐厨垃圾中典型组分的裂解液化特征研究

利用实验室规模的实验装置管式加热炉进行餐厨垃圾热解实验,实验分析了反应温度对餐厨垃圾热解产物分布的影响,米饭、白菜、猪肉、塑料和纸5种原料在最佳温度下可实现热解油质量产率的最大化,分别为45.02%、24.55%、61.19%、73.77%和24.86%。其中,米饭和白菜热解油含水率较高,可达到30%~40%,将含水率降到15%后,测定热值分别为25.51 MJ/kg和17.75 MJ/kg。塑料和纸混合热解时,塑料热解过程的放热效应可缩小纸的热解温度区间,增加热解油产量。红外光谱分析厨余热解油包含多种含氧有机物。通过气质联用仪(GC-MS)分析塑料热解油和塑料与纸混合热解油在180℃以下蒸馏出的液相产物,主要组分为烷烃和烯烃,从成分和热值分析,与汽油、柴油相近。     

船舶塑料垃圾热解特性及动力学分析

利用热重分析(TGA)研究船舶塑料垃圾在不同升温速率和不同气氛下的热解特性,并得到了热解动力学参数。结果表明,船舶塑料垃圾的热解过程主要有3个阶段,比一般塑料热解复杂;随着升温速率增大,最大热解速率和最大热解速率温度等热解特性参数也增大,反应变得更剧烈;N2/CO2比为4∶1时,热解反应进行得最完全,固体残留率最少。动力学分析表明,采用3个连续一级反应模型能很好地拟合实验数据;不同的升温速率和气氛比对反应各阶段活化能均有不同程度的影响。     

两段式热解厨余垃圾实验研究

通过厨余垃圾的工业分析，发现其挥发分比例较高，适合热解利用；采用热重分析方法分析了不同条件下厨余垃圾的热解特性，提出了厨余垃圾两段式热解转化利用的思路，得出了厨余垃圾热解的合适工艺条件。在自行设计建造的一段回转炉、二段焦化罐中对厨余垃圾热解，并分析了产物的组成和性质。     

固体废物在固定床式热解炉内热解产气特性的实验研究

垃圾热解技术以其较低的污染排放和较高的能源回收率在固体废弃物处理领域里占有重要地位。利用小型外热型热解炉对城市垃圾、生物质及有害固体废弃物进行热解实验 ,分析发现 ,物料的挥发分、加热方式以及热解终温等对产气影响大 ,随温度的增加产气中H2 含量逐渐增多 ,C2 H4和C2 H6 的含量逐渐下降 ,气体热值有一个最大值。     

固体废物在固定床式热解炉内热解产气特性的实验研究

垃圾热解技术以其较低的污染排放和较高的能源回收率在固体废弃物处理领域里占有重要地位。利用小型外热型热解炉对城市垃圾、生物质及有害固体废弃物进行热解实验，分析发现，物料的挥发分、加热方式以及热解终温等对产气影响大，随温度的增加产气中H2含量逐渐增多，C2H4和C2H6的含量逐渐下降，气体热值有一个最大值。     

城郊乡村生活垃圾衍生燃料热解特性研究

将城郊乡村生活垃圾加工成粒径6.0 mm左右的垃圾衍生燃料(RDF),采用热重(TG)分析和红外光谱等研究其热解特性.结果表明:(1)在RDF挥发分阶段和生物质挥发分阶段,助燃添加剂处于活泼分解阶段,加入了30％(质量分数)秸秆、玉米芯等生物质作助燃添加剂后的RDF(以下简写为混合RDF)分子碎片正发生内部氢重排,总体挥发分产物较多,并且有明显的二次裂解,失重提高到4.85 mg,失重率约提高12％.在RDF与生物质重叠的碳固定阶段,助燃添加剂失重率有一定提高,热重微分(DTG)峰值速率增加,为RDF碳固定阶段的进一步热解提供了良好的支持.(2)快加热产气速率均大于慢加热.(3)热解终温越高,越有利气体析出.(4)RDF的热解固体产率随着热解终温的升高而降低,在850℃时为31.9％;热解气体产率随着热解终温升高而迅速升高,在850℃时可达49.8％.(5)根据红外光谱图,城郊乡村生活垃圾加工成的RDF中所含的氯元素基本上以HCl形式释放.(6)一级动力学反应可以准确地描述物料热解过程.     

热解条件对废旧电路板真空热解油的成分的影响

采用GC/MS检测,研究最终温度(400、500和600℃)和升温速率(5、10和15℃/min)对废旧电路板真空热解油的成分的影响。研究表明,最终温度过高(600℃)、升温速率较小(5℃/min)或较大(15℃/min)都不利于热解油的形成,反而增大不凝气的产量。升高最终温度会增强较低碳数物质的热解效果,产生更多的不凝气;但同时也会限制较高碳数物质的热解,出现较多的环化、聚合反应生成结构复杂的物质。升温速率较高(15℃/min),会产生大量不饱和物质,其在后续发生环化、聚合等反应,生成更多的C14~C18,C6~C9含量则大幅下降。从热解油产量和GC/MS检测结果看,升温速率为10℃/min、最终温度为500℃和恒温1 h,热解充分,热解油C6~C9含量高,有较高的综合利用价值。     

生活垃圾催化热解液体产物特性

为探索生活垃圾催化热解液体产物特性变化规律,选取Na2CO3、CaO、Fe2O33种催化剂,利用固定床实验、红外分析(FT-IR)进行生活垃圾热解液体产物产率和组分特性研究.结果表明,热解终温600℃无催化剂时,生活垃圾热解液产率为39.80 wt％,添加3种催化剂后热解液产率均降低;生活垃圾分别添加1％的Na2CO3和CaO后,热解油氧含量由22.49％分别降低到20.12％和18.53％,低位热值由30.30 MJ/kg分别提高到33.79和32.74 MJ/kg;无催化剂时热解油成分为脂肪类、含氧化合物及少量芳香类混合物,加催化剂后热解油中芳香类物质峰面积比例显著增加,而含氧化合物峰面积比例降低,羟基类及羧酸类含氧化合物峰面积比例明显减少,其他含氧物峰面积比例却增加;CaO催化效果较明显,生活垃圾添加1％的CaO热解油中芳香类物质峰面积比例从4.36％增加到29.46％,含氧化合物峰面积比例由49.42％降低到23.12％,其中羟基类和羧酸类化合物峰面积比例分别由34.03％和10.65％降低到0.00％和3.34％,其他含氧化合物峰面积比例由4.73％增加到19.77％.     

生活垃圾灰渣对生物质的热解特性及动力学的影响

生活垃圾热解焚烧产生的热灰渣可以作为热解过程的热载体。为研究灰渣对生活垃圾中生物质热解的影响,在热重分析仪中将生活垃圾的典型组分木屑和纸屑分别与2种垃圾灰渣混合热解,并进行热解动力学研究。结果表明,城市生活垃圾的热解焚烧炉灰渣(A灰)可以提高木屑和纸屑的热解转化率,比理论值高出4%～5%。农村生活垃圾热解焚烧炉的灰渣(B灰)对纸屑热解具有促进作用,但对木屑的热解没有显著影响。动力学研究表明,混入A灰后,木屑热解的第1、第2阶段的表观活化能都大幅降低,与其提高木屑的热解转化率的结果相一致。B灰也使得木屑的热解第1阶段活化能降低。此外,A灰和B灰均可以显著降低纸屑第1段热解的活化能。     

城市生活垃圾典型组分的热解动力学分析

利用热分析仪对城市生活垃圾中典型组分的热解过程进行了热重分析实验，采用不同形式的反应机理函数对实验结果进行了线性拟合计算，得到了针对不同组分的最合理的反应机理函数形式，并求出了相应的反应活化能E及频率因子A，由此构建了能更准确地反映垃圾各组分的热解反应过程的动力学模型。计算结果表明，垃圾中多数组分的热解过程用扩散模型来表示最为合理。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.