基于Fluent的整体式催化反应系统降解甲苯的数值模拟

为得到甲苯在整体式催化系统中的燃烧规律,利用Fluent 18.1对整体式催化反应系统中甲苯-空气在铂(Pt)上的燃烧特性进行了数值模拟。通过假设多孔介质内气固间局部能够达到热平衡,建立了三维的多孔介质催化燃烧模型。经验证,该模型能够很好地反映甲苯在整个系统中的燃烧特性。通过对整个反应系统中温度场、浓度场和速度场的工况探究和通过分段控制燃烧反应发现:贫燃条件有利于催化燃烧,富燃条件有利于引发热力燃烧;当量比小于1,入口流速小于2 m·s~(-1)时,有利于催化燃烧,催化转化率在96%以上;当量比较高,入口流速较大时,有利于引发热力燃烧。以上研究结果为该技术的实际应用提供了参考。     

黑麦草根际强化微生物净化甲苯

采用在普通生物反应器上种植黑麦草的方法,研究了黑麦草根系强化微生物净化甲苯污染气体的作用,及甲苯入口浓度、填料深度、温度对反应器净化甲苯速率的影响。结果表明,在生物反应器相同的填料深度,细菌数量的水平分布为黑麦草根际区>过渡区>非根际,与相同位置的甲苯浓度分布呈负相关,说明黑麦草根系通过促进细菌的活性进而增加甲苯的降解。在相同的甲苯入口浓度下,甲苯的净化速率随着填料深度的增加而增加,在甲苯入口浓度不高于500 mg/m3条件下,相同的填料深度,反应器对甲苯的净化速率随着甲苯浓度的增加而增加。在5~35℃范围内,温度升高有助于提高微生物活性,促进微生物对甲苯的降解,且有黑麦草处理的甲苯净化速率大于同等条件下无黑麦草处理。     

Cu-Mn-O制备条件对其催化燃烧甲苯性能的影响

以甲苯催化燃烧为模型反应,考察了Cu-Mn-O催化剂共沉淀制备方法中沉淀剂、滴加方式和焙烧温度对其催化活性的影响.结果表明,以Na2CO3为沉淀剂、反滴(金属离子溶液滴加到碱液)、500℃焙烧所制得的催化剂具有较高的活性,其甲苯完全燃烧(甲苯转化率98%以上)温度为220℃.多晶粉末衍射(XRD)和比表面积(BET)表征发现,在Cu1.5Mn1.5O4晶相中掺杂少量的CuO晶相可以有效地提高催化剂活性,催化剂的比表面积(BET)越大,活性越高.     

新型Cu-Co-O_x催化剂的制备及其催化燃烧甲苯的性能研究

采用浸渍法制备自制载体负载复合金属氧化物Cu-Co-Ox催化剂。研究了Cu-Co-Ox催化剂催化燃烧甲苯的活性。分别考察了Cu-Co-Ox负载量、Cu/Co(摩尔比)及焙烧温度对催化燃烧甲苯活性的影响,并采用X射线衍射(XRD)及扫描电镜(SEM)等表征技术,分别对复合金属氧化物Cu-Co-Ox的晶型与结晶形貌进行了分析。结果表明,焙烧温度为600℃,Cu-Co-Ox负载量为5%(质量分数),Cu/Co为1∶2时,Cu-Co-Ox催化燃烧甲苯的活性最高。当反应温度为250℃,甲苯的转化率达到95%以上。XRD分析表明,Cu-Co-Ox催化剂主要活性相为CuCo2O4尖晶石。     

气-固流化床光催化氧化甲苯的研究

在自制的流化床光催化反应装置中研究了中低浓度（28～140 mg/m^3）甲苯的气相光催化降解过程,考察了光照时间、初始浓度、表观气速和催化剂负载量等因素对甲苯光催化降解率的影响规律.结果表明,紫外灯照射约1.5 h,甲苯的转化率达最大值,甲苯初始浓度越低,维持此最大值的时间越久;在一定低浓度范围内（28～55 mg/m^3）,甲苯的转化率不随浓度变化,符合一级反应动力学,浓度进一步增加,则甲苯的转化率下降;表观气速和催化剂负载量的最佳值分别为3.3Umf和0.19 g TiO2/g SiO2.     

流向变换反应器中Pd/Zr-Mn-O/载体催化剂对甲苯的催化燃烧

在流向变换催化燃烧反应体系中,通过操作参数(甲苯浓度、空速及切换周期)对热波形状与特征参数(波峰温度、平均温度和移动速度)影响的考察,结果表明,较佳的操作参数为:甲苯浓度800～3 200 mg/m3,空速2 000～12 000h-1,切换周期2～10 min,空速和甲苯浓度对热波移动速度的影响较大,热波波峰温度和反应器平均温度随着甲苯浓度的增加而增加,随着切换周期的缩短而升高,随着空速的增加先升高后降低,与固定床装置相比,在流向变换装置中催化剂的活性更高,甲苯去除率在96.5%以上。     

盆栽植物净化甲苯废气

采用动态模拟法模拟盆栽植物对甲苯污染气体的净化,考察吊兰和金绿萝两种盆栽植物在净化甲苯过程中,甲苯入口浓度与植物对甲苯净化速率的关系。结果表明,2种盆栽植物对低浓度甲苯废气具有长期明显的净化效果。在相同条件下,吊兰茎叶和土壤的净化速率优于金绿萝体系。在植物的耐受浓度范围内,2种植物茎叶和土壤的净化速率均随着甲苯入口浓度的升高而增大,且白天的净化速率明显高于黑夜时的净化速率。在实验过程中,吊兰土壤体系的降解率随着甲苯浓度的升高逐渐下降;金绿萝土壤体系的降解率基本不受甲苯入口浓度的影响。吊兰盆栽体系的降解率明显大于金绿萝的降解率。两种植物盆栽体系的降解率随甲苯进口浓度的影响可以忽略。     

气-固流化床光催化氧化甲苯的研究

在自制的流化床光催化反应装置中研究了中低浓度(28~140mg/m3)甲苯的气相光催化降解过程,考察了光照时间、初始浓度、表观气速和催化剂负载量等因素对甲苯光催化降解率的影响规律。结果表明,紫外灯照射约1·5h,甲苯的转化率达最大值,甲苯初始浓度越低,维持此最大值的时间越久;在一定低浓度范围内(28~55mg/m3),甲苯的转化率不随浓度变化,符合一级反应动力学,浓度进一步增加,则甲苯的转化率下降;表观气速和催化剂负载量的最佳值分别为3·3Umf和0·19gTiO2/gSiO2。     

活性组分稀土氧化物对甲苯催化燃烧性能的影响

以活性组分氧化铜、氧化锰为基础,加入活性组分稀土氧化物,研究对甲苯催化燃烧性能影响。研究结果表明,在所选稀土氧化物中,加入氧化铈时甲苯的起燃温度和完全燃烧温度最低;在一定的负载量下,Cu∶Mn∶Ce摩尔比为1∶2∶0.7时,制备的Cu Mn Ce/Zr O2整体催化剂甲苯完全燃烧温度最低;催化剂合理的焙烧温度为500℃,此时甲苯的起燃温度约200℃,完全燃烧温度为220℃;催化剂合理的焙烧时间为3 h。     

有机复合填料生物滤床对甲苯气体的净化

利用一种新型有机复合填料作为生物滤床中微生物的附着载体,接种经过驯化筛选的专性甲苯降解菌,填装于生物过滤塔中净化低浓度甲苯气体。研究了新型有机复合填料在长期运行时的情况,考察了进气流量、入口浓度、床层温度和填料湿度对生物滤床的影响,最终经过优化得出,此种填料的生物滤床能够为微生物提供良好的附着生长环境,并能保持滤床的高效稳定运行,当进气流量为0.4 m3/h,入口浓度为400 mg/m3,床层温度为30℃,填料湿度为50%时,生化去除量达到30.6 g/(m3.h),并且在此条件下滤床具有良好的耐冲击性能。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Spectrophotometric Determination of Atmospheric Acidity by means of the Displacement of the Equilibrium of Acid-Base Indicators

A method is described for determining acidity by means of the spectrophotometric determination of the displacement of the equilibrium of açid-base indicators. The method is simple, sensitive and free of known interferences. There is no dependence on costly or sophisticated equipment and the results obtained are reliable and reproducible.     

实验室质量管理体系内部审核的策划

在实施ISO／IEC 17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核策划阶段的关键环节，提出审核范围确定、审核计划和抽样方案制订的质量控制要求，为有序高效地实施内部审核提供了技术方法。