锰-稀土/Y分子筛复合电催化处理含酚模拟废水

采用浸渍焙烧法制备了以Y分子筛为载体的Mn-RE复合催化剂,置于电解槽内形成反应床体,构建Mn-RE多相催化电解氧化体系处理人工模拟苯酚废水.考察了浸渍液中锰的质量分数、稀土元素组成和质量分数、焙烧温度、焙烧时间对电催化活性的影响,用SEM和XRD等手段对催化剂的微观结构、表面形貌进行了表征,探讨了Mn-RE/Y分子筛催化剂对含酚废水降解的电催化效果.研究表明, Mn-RE/Y分子筛催化剂的最佳制备条件是浸渍液中锰质量分数6%,铈质量分数为3%,焙烧温度为550℃,焙烧时间为5h.Y分子筛中引入Mn、Ce后没有破坏Y分子筛的晶体结构, Mn-RE/Y分子筛催化剂的表面并没有检测到稀土氧化物和锰氧化物的物相.反应过程中, Mn-RE/Y分子筛在阴极和阳极的同时催化氧化作用强化了含酚废水的降解效果.     

CuMnO_x/γ-Al_2O_3对含甲苯废气催化燃烧的性能研究

利用浸渍法制备催化剂CuO/γ-Al2O3、MnOx/γ-Al2O3、CuMnOx/γ-Al2O3,通过实验研究表明:CuMnOx/γ-Al2O3具有更高的催化活性,其T99比其他两种催化剂要低50℃以上。在焙烧温度300、400、500、600℃下制备CuMnOx/γ-Al2O3,比较其催化活性,发现在600℃制备的催化剂要比其他温度下制备的同等催化剂的催化活性高,证明了尖晶石结构在催化燃烧中起着很大的作用。     

新型CuMn/TiO2苯类催化燃烧催化剂的研制及活性实验

采用浸溃法制备了CuMn/TiO2新型甲苯燃烧催化剂,其活性明显优于传统CuMn/γ-Al2O3和Cu-Mn复合氧化物催化剂.研究发现,载体TiO2自身有一定催化活性,而γ-Al2O3则几乎没有活性;TiO2与Cu-Mn之间的协同作用更提高了新型催化剂的活性.XRD、LRS结果显示,CuMn/TiO2催化剂的主要活性相为铜锰尖晶石(CuMn2O4),它的存在是CuMn/TiO2催化活性优良的另一个主要原因.考察了Cu-Mn负载量、铜锰比和焙烧温度对催化剂活性的影响,CuMn/TiO2下对甲苯的去除率达95%以上时催化床层温度为215℃,比CuMn/γ-Al2O3和Cu-Mn复合氧化物对甲苯去除率达95%时分别下降了30℃、50℃左右.     

V-W/TiO_2/γ-Al_2O_3催化剂催化还原NO的研究

掺杂15%TiO2对γ-Al2O3改性制备了TiO2/γ-Al2O3复合氧化物载体,以此复合氧化物及TiO2、γ-Al2O3为载体用浸渍法负载钒钨制备了一系列催化剂,采用比表面积和孔结构分析、X射线衍射(XRD)、高分辨电镜(HRTEM)、原位红外(in situ FT-IR)等技术对载体和催化剂进行宏观-微观表征,同时在模拟氨气选择性催化还原NO(NH3-SCR)的反应条件下对催化剂的脱硝反应活性进行考察,比较研究TiO2掺杂对V2O5-WO3/TiO2和V2O5-WO3/γ-Al2O3催化剂的改性作用。结果发现,少量TiO2掺杂制得的TiO2/γ-Al2O3复合载体中,TiO2和γ-Al2O3之间的协同作用使得V2O5-WO3/TiO2/γ-Al2O3催化剂的选择性催化还原脱硝效率及活性窗口明显优于单一载体制备的催化剂,并表现出了良好的热稳定性;各种表征结果表明,TiO2/γ-Al2O3复合载体中TiO2高度分散在γ-Al2O3上,复合载体具有较大的比表面积,载体表面存在大量的Br?nsted酸位和较多的活性中间产物,这些可能是TiO2/γ-Al2O3复合载体催化剂具有较好SCR活性的原因。     

TiO_2对In-Ag-O/γ-Al_2O_3催化剂上CO选择性还原NO的改性研究

以Ti O2、γ-Al2O3及Ti O2-γ-Al2O3复合氧化物为载体,以In-Ag-O基为活性组分,采用等体积浸渍法制备了一系列In/Ag催化剂,通过XRD、BET、SEM、H2-TPR等技术手段对催化剂表面形态进行分析,并考察了催化剂对CO选择性还原NO的反应活性和载体中Ti O2含量对催化性能的影响.结果表明,Ti O2的添加促进了活性组分铟和银物种的分散,当Ti O2的含量为载体的15%时制备的催化剂活性最高,合适的Ti O2与γ-Al2O3配比使活性组分与载体之间发生了强烈的相互作用,由此提高了CO选择性还原NO的活性.     

纳米TiO_2-Al_2O_3负载CuMnO_x对甲苯的催化燃烧

研究采用改进的溶胶-凝胶法制备了TiO2-Al2O3复合载体,并用浸渍法制备CuMnOX/TiO2-Al2O3催化剂,通过对甲苯废气催化燃烧的实验,分别考察了Cu-Mn负载量、Cu/Mn摩尔比、焙烧温度及载体对催化剂制备过程及催化剂活性的影响。实验结果表明:活性组分负载量25%,铜锰活性组分的配比Cu:Mn=1:2,焙烧温度500℃是浸渍法制备CuMnOX/TiO2-Al2O3催化剂较佳的工艺条件;XRD衍射图谱表明,500℃下铜锰尖晶石的存在是催化剂催化活性优良的主要原因;由复合载体制备的CuMnOX/TiO2-Al2O3催化剂比单一载体制备的CuMnOX/Al2O3催化剂具有更高的甲苯转化率,其T99比单一载体要低20℃以上。     

光助Fenton反应催化剂Fe/Al2O3的制备及其对六氯苯的催化活性研究

采用超声促进浸渍法制备了光助Fenton催化剂Fe/Al2O3,利用该催化剂对六氯苯（HCB）进行光助Fenton氧化降解,考察了浸渍液浓度、浸渍温度、灼烧温度和灼烧时间等制备条件对其催化降解六氯苯的活性的影响,确定了制备Fe/Al2O3的工艺条件,并对制得的催化剂进行表征。结果表明,超声促进浸渍法制备非均相光助Fenton反应催化剂Fe/Al2O3的最佳工艺条件为：浸渍液浓度25mmol/L,浸渍温度40℃,焙烧温度500℃,焙烧时间3h。在此条件下制备的催化剂对六氯苯的降解具有较高的催化活性。     

Catalytic performance of copper and cerium oxides-based γ-Al_2O_3 on combustion of toluene

以γ-Al2O3为载体,以复合氧化物CuxCe1-xO2为活性组分,其中,x=0.1,0.2,0.4,0.6,0.8,通过浸渍法制备了一系列CuxCe1-xO2/γ-Al2O3催化剂.在固定床反应器中评价了催化剂对甲苯的催化活性,通过XRD、SEM对催化剂进行表征,并运用ICP-MS分析并计算Cu、Ce的摩尔比以及活性组分的负载量.结果表明,在CuxCe1-xO2/γ-Al2O3催化剂中Cu、Ce摩尔比的实际值与理论值相近,活性组分的负载量在19%以上,而且对甲苯都有较好的低温催化活性,其中当x=0.2时,即Cu0.2Ce0.8O2/γ-Al2O3催化剂对甲苯的催化活性最高,其中T10=160℃,T90=265℃;当甲苯的进口浓度在700～3000mg·m-3时,进口浓度对Cu0.2Ce0.8O2/γ-Al2O3催化剂的催化活性影响较小,且经过连续80h的稳定性操作后转化率仍然保持在90%以上.     

催化湿式氧化法处理桉木CTMP模拟废水

通过浸渍法制备固载金属非均相型催化剂,用于催化湿式氧化处理桉木CTMP模拟废水。结果表明:在焙烧温度400℃,焙烧时间4h,浸渍液浓度为6%,浸渍时间为5h下制得的CuO/γ-Al2O3催化剂的催化活性最好;在反应时间为8h,鞣酸溶液pH为4.5,H2O2加入量为0.2mL,催化剂用量为4g的条件下处理鞣酸溶液的效果最好,鞣酸去除率>90%。     

Pd-W-Cu/γ-Al_2O_3催化氢还原脱硝的基本性能研究

采用浸渍法制备Pd-W-Cu/γ-Al2O3催化剂,用XRD和SEM方法对该催化剂进行了表征.以氢气作为还原剂,在间歇式反应器中对催化还原地下水中硝酸盐进行了实验研究,考察了催化剂制备方法对催化还原硝酸盐性能的影响.结果表明,W的添加改善了Pd的分散性,提高了催化剂的活性和选择性.金属Pd/W/Cu质量比、浸渍顺序和焙烧温度对催化性能有较大影响.Pd/W/Cu质量比为3∶1∶1,Pd、Cu和W3种金属组分同时浸渍,焙烧温度为400℃时,催化剂的活性和选择性最高.在NO3--N初始浓度为100mg·mL-1条件下,催化反应60min后水中NO3--N和NO2--N浓度均为0mg·mL-1,NH4+-N浓度为2.5mg·mL-1.     

Distribution and ecological effect of mercury in Laogang landfill, Shanghai, China

Laogang landfill near Shanghai is the largest landfill in China, and receives about 10000 t of daily garbage per day, Samples of topsoil and plants were analyzed to evaluate mercury pollution from the landfill. For topsoil samples, there were significant correlations among total mercury （HgT）, combinative mercury （Hgc） and gaseous mercury （HgG）, and content of total organic carbon （TOC）, but, no significantly relationship was found between Hg content and filling time. Hg content changes in vertical profiles with time showed that the average Hgv of profiles 1992, 1996, and 2000 was similar, but their average HgG was quite different. HgT was significantly correlated with Hgc in profile 1992 and 2000, and Hgv was significantly correlated with Hg6 in profile 1996. HgG/Hgv ratio in profile samples decreased in the order of （HgG,/HgT）1992〉（HgG/HgT）1996〉〉（HgG/HgT）2000. A simple outline of Hg release in landfill could be drawn： with increasing of filling time, degradation undergoes different biodegradation, accordingly, gaseous mercury goes through small, more, and small proportion to total mercury. Distribution of Hg in plants was inhomogeneous, following the order of leaf〉root〉stem. The highest value of leaf may be associated with higher atmospheric Hg from landfill. Ligneous plants （e.g. Phyllostachys glanca, Prunus salicina and Ligustrum lucidum） are capable of enriching more Hg than herbaceous plants.     

EDTA-enhanced phytoremediation of lead contaminated soil by Bidens maximowicziana

Phytoremediation is a potential cleanup technology for the removal of heavy metals from contaminated soils.Bidens maximowicziana is a new Pb hyperaccumulator,which not only has remarkable tolerance to Pb but also extraordinary accumulation capacity for Pb.The maximum Pb concentration was 1509.3 mg/kg in roots and 2164.7 mg/kg in overground tissues.The Pb distribution order in the B. maximowicziana was:leaf>stem>root.The effect of amendments on phytoremediation was also studied.The mobility of soil Pb and the Pb concentrations in plants were both increased by EDTA application.Compared with CK(control check),EDTA application promoted translocation of Pb to overground parts of the plant.The Pb concentrations in overground parts of plants was increased from 24.23-680.56 mg/kg to 29.07-1905.57 mg/kg.This research demonstrated that B.maximowicziana appeared to be suitable for phytoremediation of Pb contaminated soil,especially,combination with EDTA.     

Decomposition of alachlor by ozonation and its mechanism

Decomposition and corresponding mechanism of alachlor, an endocrine disruptor in water by ozonation were investigated. Results showed that alachlor could not be completely mineralized by ozone alone. Many intermediates and final products were formed during the process, including aromatic compounds, aliphatic carboxylic acids, and inorganic ions. In evoluting these products, some of them with weak polarity were qualitatively identified by GC-MS. The information of inorganic ions suggested that the dechlorination was the first and the fastest step in the ozonation of alachlor.     

Enzymatic oxidation of aqueous pentachlorophenol

The influence of the nonionic surfactant Tween 80 on pentachlorophenol （PCP） oxidation catalyzed by horseradish peroxidase was studied. The surfactant was tested at concentrations below and above its critical micelle concentration （CMC）. Enhancement of PCP removal was observed at sub-CMCs. The presence of Tween 80 in the reaction mixture reduced enzyme inactivation which occurred through a combination of free radical attack and sorption by precipitated products. A simple first-order model was able to simulate time profiles for enzyme inactivation in the presence or absence of Tween 80. At supra-CMCs, the surfactant caused noticeable reductions in PCP removal, presumably through micelle partitioning of PCP which precluded the hydrophobic PCP molecule from interacting with the enzyme.     

基于综合水质标识指数和对应分析法的校园河道水质评价

以三峡大学的校园河道求索溪为研究对象,利用综合水质标识指数法确定求索溪水质类别,分析其水质时空变化规律,并利用对应分析法得出求索溪中不同监测点的主要污染因子.研究结果表明:求索溪整体的综合水质标识指数为7.423,整体水质为劣V类(地表水环境质量标准GB 3838-2002)且黑臭.从时间变化来看,求索溪4月份的水质最差,5月份次之,4、5月份所有监测点的水质都劣于V类且黑臭;8月份水质最好,水质为Ⅳ类;从空间分布来看,8个监测点综合水质标识指数均超过6.0,水质为劣V类,其中6号监测点的水质相对最好,监测点3号的水质相对最差;对应分析法得出求索溪的整体水体污染程度受总氮因子的影响最大,其次为总磷.该研究拟为求索溪及类似校园河道的水环境治理研究提供基础依据和参考.     

Effects of chitosan on growth of an aquatic plant (Hydrilla verticillata) in polluted waters with different chemical oxygen demands

Effects of chitosan on a submersed plant, Hydrilla verticillata, were investigated. Results indicated that H. venicillata could prevent ultrastructure phytotoxicities and oxidativereaction from polluted water with high chemical oxygen demand (COD). Superoxide dismutase (SOD) activity and malondialdehyde (MDA) contents in H. verticillata treated with 0.1% chitosan in wastewater increased with high COD (980 mg/L) and decreased with low COD (63 mg/L), respectively. Ultrastructural analysis showed that the stroma and grana of chloroplast basically remained normal. However, plant cells from the control experiment (untreated with chitosan) were vacuolated and the cell interval increased. The relict of protoplast moved to the center, with cells tending to disjoint. Our findings indicate that wastewater with high COD concentration can cause a substantial damage to submersed plant, nevertheless, chitosan probably could alleviate the membrane lipid peroxidization and ultrastructure phytotoxicities, and protect plant cells from stress of high COD concentration polluted water.     

Removal of cadmium using MnO2 loaded D301 resin

MnO2 loaded weak basic anion exchange resin D301 （Anion exchange resin, macroreticular weak basic styrene） as adsorbent has been prepared and applied to the removal of cadmium. The adsorption characteristics have been investigated with respect to effect of pH, equilibrium isotherms, removal kinetic data, and interference of the coexisting ions. The results indicated that the Cd^2＋ could be efficiently removed using MnO2 loaded D301 resin in the pH range of 3-8 from aqueous solutions with the co-existence of high concentration of alkali and alkaline-earth metals ions. The saturate adsorption capacity of the Cd^2＋ was 77.88 mg/g. The adsorption process followed the pseudo first-order kinetics. The equilibrium data obtained in this study accorded excellently with the Langmuir adsorption isotherm.     

Effect of coagulation pretreatment on the fouling of ultrafiltration membrane

The purpose of this study is to understand the effect and mechanism of preventing membrane fouling, by coagulation pretreatment, in terms of fractional component and molecular weight of natural organic matter （NOM）. A relatively higher molecular weight （MW） of hydrophobic compounds was responsible for a rapid decline in the ultrafiltration flux. Coagulation could effectively remove the hydrophobic organics, resulting in the increase of flux. It was found that a lower MW of neutral hydrophilic compounds, which could remove inadequately by coagulation, was responsible for the slow declining flux. The fluxes in the filtration of coagulated water and supernatant water were compared and the results showed that a lower MW of neutral hydrophilic compounds remained in the supernatant water after coagulation could be rejected by a membrane, resulting in fouling. It was also found that the coagulated flocs could absorb neutral hydrophilic compounds effectively. Therefore, with the coagulated flocs formed on the membrane surface, the flux decline could be improved.     

Penetration analysis of elements and bioleaching treatment of spent refractory for recycling

Acidithiobacillus ferrooxidans ATCC23270 and Acidithiobacillus thiooxidans TM-32 were used for bioleaching of spent refractories of aluminium and copper melting furnaces for their recycling.Firstly,penetration of elements into aluminium melting furnace refractory was investigated and it was found that up to 7 cm from surface was contaminated.Comparison on leaching efficiency by the strains ATCC23270 and TM-32 found that the strain ATCC23270 could treat larger amount of the refractories than the strain TM-32 could do.In the experiment of bioleaching of spent refractory aluminium melting furnace by the strain ATCC23270,high leaching efficiency were obtained on Al,Si,and Ca,and extremely low leaching performance was,however,shown on the rest of elements i.e.,Na,Mn,and Zn.Under the strain TM-32 use,relatively high leaching performance was recognized on Al,Si,Ca,Na,Mn,and Zn.In the experiment of bioleaching for spent refractory copper melting furnace,almost the same leaching trends were shown on Cu,Zn,Al,and Si under the strains ACTT23270 and TM-32 uses.     

Simultaneous removal of ammonium and phosphate by zeolite synthesized from coal fly ash as influenced by acid treatment

Zeolite synthesized from fly ash （ZFA） without modification is not efficient for the purification of NH4＋ and phosphate at low concentrations that occur in real effluents, despite the high potential removal capacity. To develop an effective technique to enhance the removal efficiency of ammonium and phosphate at low concentrations, ZFA was modified with acid treatment and the simultaneous removal of ammonium and phosphate in a wide range of concentration was investigated. It was seen that when compared with untreated ZFA, only the treatment by 0.01 mol/L of H2SO4 significantly improved the removal efficiency of ammonium at low initial concentrations. The behavior was well explained by the pH effect. Treatment by more concentrated H2SO4 led to the deterioration of the ZFA structure and a decrease in the cation exchange capacity. Treatment by 0.01 mol/L H2SO4 improved the removal efficiency of phosphate by ZFA at all initial P concentrations, while the treatment by concentrated H2SO4 （≥0.9 mol/L） resulted in a limited maximum phosphate immobilization capacity （PIC）. It was concluded that through a previous mild acid treatment （e.g. 0.01 mol/L of H2SO4）, ZFA can be used in the simultaneous removal of NH4＋ and P at low concentrations simulating real effluent.