Atrazine and alachlor transport in claypan soils as influenced by differential antecedent soil water content

Increased attention to ground water contamination has encouraged an interest in mechanisms of solute transport through soils. Few studies have investigated the effect of the initial soil water content on the transport and degradation of herbicides for claypan soils. We investigated the effect of claypan soils at initial field capacity vs. permanent wilting level on atrazine and alachlor transport. The soil studied was Mexico silt loam (fine, smectitic, mesic Aeric Vertic Epiaqualf) with a subsoil clay content, primarily montmorillonite, of >40%. Strontium bromide, atrazine, and alachlor were applied to plots; half were at field capacity (Wet treatment), and half were near the permanent wilting point (Dry treatment). Soil cores were removed at selected depths and times, and cores were analyzed for bromide and herbicide concentrations. Bromide, atrazine, and alachlor were detected at the 0.90-m depth in dry plots within 15 d after experiment initiation. Bromide was detected 0.15 m deeper (P < 0.05) in the Dry compared with the Wet treatment at 1, 7, and 60 d after application and >0.30 m deeper (P < 0.01) in the Dry treatment at 15 and 30 d after application; similar treatment results were found for atrazine and alachlor, although on fewer dates with significant differences. The mobility order of the applied chemicals was bromide > atrazine > alachlor. The atrazine apparent half-life was significantly longer in the Dry plots compared with the Wet plots. The retardation factor determined from the relative velocity of each herbicide to that of bromide was higher for alachlor than for atrazine. This study identifies the impact that shrinkage cracks have for different moisture conditions on preferential transport of herbicides in claypan soils.     

Comparative losses of glyphosate and selected residual herbicides in surface runoff from conservation-tilled watersheds planted with corn or soybean

Residual herbicides regularly used in conjunction with conservation tillage to produce corn ( L.) and soybean [ (L.) Merr] are often detected in surface water at concentrations that exceed their U.S. maximum contaminant levels (MCL) and ecological standards. These risks might be reduced by planting glyphosate-tolerant varieties of these crops and totally or partially replacing the residual herbicides alachlor, atrazine, linuron, and metribuzin with glyphosate, a contact herbicide that has a short half-life and is strongly sorbed to soil. Therefore, we applied both herbicide types at typical rates and times to two chisel-plowed and two no-till watersheds in a 2-yr corn/soybean rotation and at half rates to three disked watersheds in a 3-yr corn/soybean/wheat-red clover ( L.- L.) rotation and monitored herbicide losses in surface runoff for three crop years. Average dissolved glyphosate loss for all tillage practices, as a percentage of the amount applied, was significantly less ( ≤ 0.05) than the losses of atrazine (21.4x), alachlor (3.5x), and linuron (8.7x) in corn-crop years. Annual, flow-weighted, concentration of atrazine was as high as 41.3 μg L, much greater than its 3 μg L MCL. Likewise, annual, flow-weighted alachlor concentration (MCL = 2 μg L) was as high as 11.2 and 4.9 μg L in corn- and soybean-crop years, respectively. In only one runoff event during the 18 watershed-years it was applied did glyphosate concentration exceed its 700 μg L MCL and the highest, annual, flow-weighted concentration was 3.9 μg L. Planting glyphosate-tolerant corn and soybean and using glyphosate in lieu of some residual herbicides should reduce the impact of the production of these crops on surface water quality.     

Anionic polyacrylamide effects on soil sorption and desorption of metolachlor,atrazine, 2,4-D,and picloram

Polyacrylamide (PAM) treatment of irrigation water is a growing conservation technology in irrigated agriculture in recent years. There is a concern regarding the environmental impact of PAM after its application. The effects of anionic PAM on the sorption characteristics of four widely used herbicides (metolachlor, atrazine, 2,4-D, and picloram) on two natural soils were assessed in batch equilibrium experiments. Results showed that PAM treatment kinetically reduced the sorption rate of all herbicides, possibly due to the slower diffusion of herbicide molecules into interior sorption sites of soil particles that were covered and/or cemented together by PAM. The equilibrium sorption and desorption amounts of nonionic herbicides (metolachlor and atrazine) were essentially unaffected by anionic PAM, even under a high PAM application rate, while the sorption amounts of anionic herbicides (2,4-D and picloram) were slightly decreased and their desorption amounts increased little. The impact mechanisms of PAM were related to the molecular characteristics of PAM and herbicides. The negative effects of PAM on the sorption of anionic herbicides are possibly caused by the enhancement of electrostatic repulsion by presorbed anionic PAM and competition for sorption sites. However, steric hindrance of the large PAM molecule weakens its influence on herbicide sorption on interior sorption sites of soil particles, which probably leads to the small interference on herbicide sorption, even under high application rates.     

Fate of diuron and linuron in a field lysimeter experiment

The environmental fate of herbicides can be studied at different levels: in the lab with disturbed or undisturbed soil columns or in the field with suction cup lysimeters or soil enclosure lysimeters. A field lysimeter experiment with 10 soil enclosures was performed to evaluate the mass balance in different environmental compartments of the phenylurea herbicides diuron [3-(3,4-diclorophenyl)-1,1-dimethyl-urea] and linuron [3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea]. After application on the agricultural soil, the herbicides were searched for in soil, pore water, and air samples. Soil and water samples were collected at different depths of the soil profile and analyzed to determine residual concentrations of both the parent compounds and of their main transformation products, to verify their persistence and their leaching capacity. Air volatilization was calculated using the theoretical profile shape method. The herbicides were detected only in the surface layer (0-10 cm) of soil. In this layer, diuron was reduced to 50% of its initial concentration at the end of the experiment, while linuron was still 70% present after 245 d. The main metabolites detected were DCPMU [3-(3,4-dichlorophenyl)-1-methylurea] and DCA (3,4-dichloroaniline). In soil pore water, diuron and linuron were detected at depths of 20 and 40 cm, although in very low concentrations. Therefore the leaching of these herbicides was quite low in this experiment. Moreover, volatilization losses were inconsequential. The calculated total mass balance showed a high persistence of linuron and diuron in the soil, a low mobility in soil pore water (less than 0.5% in leachate water), and a negligible volatilization effect. The application of the Pesticide Leaching Model (PELMO) showed similar low mobility of the chemicals in soil and water, but overestimated their volatilization and their degradation to the metabolite DCPMU. In conclusion, the use of soil enclosure lysimeters proved to be a good experimental design for studying mobility and transport processes of herbicides in field conditions.     

Residual and contact herbicide transport through field lysimeters via preferential flow

Usage of glyphosate [N-(phosphonomethyl)-glycine] and glufosinate [2-amino-4-(hydroxy-methylphosphinyl)butanoic acid] may reduce the environmental impact of agriculture because they are more strongly sorbed to soil and may be less toxic than many of the residual herbicides they replace. Preferential flow complicates the picture, because due to this process, even strongly sorbed chemicals can move quickly to ground water. Therefore, four monolith lysimeters (8.1 m(2) by 2.4 m deep) were used to investigate leaching of contact and residual herbicides under a worst-case scenario. Glufosinate, atrazine (6-chloro-N(2)-ethyl-N(4)-isopropyl-1,3,5-triazine-2,4-diamine), alachlor [2-chloro-N-(2,6-diethylphenyl)-N-(methoxymethyl) acetamide], and linuron (3-3,4-dichlorophenyl-1-methoxy-1-methylurea) were applied in 1999 before corn (Zea mays L.) planting and glyphosate, alachlor, and metribuzin [4-amino-6-(1,1-dimethylethyl)-3-(methylthio)-1,2,4-triazin-5(4H)-one] were applied in 2000 before soybean [Glycine max (L.) Merr.] planting. A high-intensity rainfall was applied shortly after herbicide application both years. Most alachlor, metribuzin, atrazine, and linuron losses occurred within 1.1 d of rainfall initiation and the peak concentration of the herbicides coincided (within 0.1 d of rainfall initiation in 2000). More of the applied metribuzin leached compared with alachlor during the first 1.1 d after rainfall initiation (2.2% vs. 0.035%, P < 0.05). In 1999, 10 of 24 discrete samples contained atrazine above the maximum contaminant level (atrazine maximum contaminant level [MCL] = 3 mug L(-1)) while only one discrete sample contained glufosinate (19 mug L(-1), estimated MCL = 150 mug L(-1)). The results indicate that because of preferential flow, the breakthrough time of herbicides was independent of their sorptive properties but the transport amount was dependent on the herbicide properties. Even with preferential flow, glyphosate and glufosinate were not transported to 2.4 m at concentrations approaching environmental concern.     

Atrazine degradation and residues distribution in two acid soils from temperate humid zone

Mineralization of atrazine and formation of extractable and non-extractable "bound" residues were followed under laboratory conditions in two contrasting soils (organic C, texture, and atrazine application history) from northern Spain. The soils, a Humic Cambisol (MP) and a Gleyic Cambisol (G) were incubated with labeled atrazine (ring-13C atrazine) at field application dose and measurements were made at different time intervals during 3 mo. Fate and behavior of atrazine along the incubation showed different patterns between the two soils, the time taken for degradation of 50% (DT50) being 9 and 44 d for MP and G soils, respectively. In MP soil, with 40 yr of atrazine application and lower organic C and clay content, more than 89% of U-13C-atrazine added was mineralized after 12 wk, with most mineralization occurring within the first 2 wk. G soil, with 10 yr of atrazine application, exhibited a more progressive U-13C-atrazine mineralization, reaching 54% of initially added atrazine at 12 wk. Hydroxyatrazine and deisopropylatrazine were the metabolites founded in the extractable fraction, demonstrating that both chemical and biological processes are involved in atrazine degradation. Soil G showed during all the incubation times an extractable residues fraction greater than that in MP soil, indicating a high potential risk of soil and water contamination. Rapid microbial degradation through s-triazine ring cleavage was proposed to be the main decomposition pathway of atrazine for the two soils studied. Bound residues pool also differed notably between soils accounting for 9 and 41% of initially added atrazine, the higher values shown by soil with higher organic matter and clay content (G soil).     

Atrazine sorption-desorption hysteresis by sugarcane mulch residue

Sorption and desorption kinetics are essential components for modeling the movement and retention of applied agricultural chemicals in soils and the fraction of chemicals susceptible to runoff. In this study, we investigated the retention characteristics of sugarcane (Saccharum spp. hybrid) mulch residue for atrazine (2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine) based on studies of sorption-desorption kinetics. A sorption kinetic batch method was used to quantify retention of the mulch residue for a wide range of atrazine concentrations and reaction times. Desorption was performed following 504 h of sorption using successive dilutions, followed by methanol extraction. Atrazine retention by the mulch residue was well described using a linear model where the partitioning coefficient (K(d)) increased with reaction time from 10.40 to 23.4 cm3 g(-1) after 2 and 504 h, respectively. Values for mulch residue K(d) were an order of magnitude higher than those found for Commerce silt loam (fine-silty, mixed, superactive, nonacid, thermic Fluvaquentic Endoaquepts) where the sugarcane crop was grown. A kinetic multireaction model was successful in describing sorption behavior with reaction time. The model was equally successful in describing observed hysteretic atrazine behavior during desorption for all input concentrations. The model was concentration independent where one set of model parameters, which was derived from all batch results, was valid for the entire atrazine concentration range. Average atrazine recovery following six successive desorption steps were 63.67 +/- 4.38% of the amount adsorbed. Moreover, a hysteresis coefficient based on the difference in the area between sorption and desorption isotherms was capable of quantifying hysteresis of desorption isotherms.     

Retention and runoff losses of atrazine and metribuzin in soil

Minimizing herbicide runoff and mobility in the soil and thus potential contamination of water resources is a national concern. Metribuzin [4-amino-6-(1,1-dimethylethyl)-3-(methylthio)-1,2,4-triazin-5(4H)-one] and atrazine [2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine] dynamics in surface soils and in runoff waters were studied on six 0.2-ha sugarcane (Saccharum spp.) plots of a Commerce silt loam (fine-silty, mixed, superactive, nonacid, thermic Fluvaquentic Endoaquept) during three growing seasons under different best management practices. Metribuzin was applied in the spring as a postemergence herbicide and atrazine was applied following winter harvest. Both herbicides were applied on top of the sugarcane rows as 0.6- or 0.9-m band width application, or broadcast application, where the entire area was treated. Maximum effluent concentrations were measured from the broadcast treatment and ranged from 600 to 1100 microg L(-1) for atrazine and 250 to 450 microg L(-1) for metribuzin. Atrazine runoff losses were highest for the broadcast treatment (2.8-11% of that applied) and lowest for the 0.6-m band treatment (1.9-7.6%), with a similar trend for metribuzin losses. Measured extractable herbicides from the surface soil exhibited a sharp decrease with time and were well described with a simple first-order decay model. For atrazine, estimates for the decay rate (lambda) were higher than for metribuzin. Results based on laboratory adsorption-desorption (kinetic-batch) measurements were consistent with field observations. The distribution coefficients (Kd) for atrazine exhibited stronger retention over time in comparison with metribuzin on the Commerce soil. Moreover, discrepancies between adsorption isotherm and desorption indicated slower release and that hysteresis was more pronounced for atrazine compared with metribuzin.     

Effect of liquid cow manure on andisol properties and atrazine adsorption

Application of animal manure amendments to agricultural soils is a common practice to improve soil fertility through the addition of essential plant nutrients. This practice may increase the potential for atrazine (2-chloro-4-ethylamino-6-isopropylamino-1, 3, 5-triazine) leaching due to competition for adsorption sites between the pesticide and dissolved organic carbon (DOC) added through manure. We evaluated the influence of liquid cow manure (LCM) application on soil properties, atrazine adsorption, and the physicochemical controlling mechanisms in an Andisol. The LCM was applied at rates equivalent to 0, 100,000, 200,000, and 300,000 L ha(-1), resulting in treatments S-0, S-100, S-200, and S-300, respectively. The LCM application increased DOC and pH of the soils immediately on addition, but pH returned to S-0 values 30 d after application. The LCM application did not modify atrazine adsorption with the two lowest application rates (S-100 and S-200), but atrazine adsorption was decreased in S-300 (K(f) = 0.96) compared with the control (S-0) (K(f) = 1.19), possibly due to the competitive adsorption of DOC with the pesticide. The Fourier-transformed infrared analysis showed that LCM increased aliphaticity and presence of N-containing groups and polysaccharide-like groups in amended soils; however, these properties did not modify the atrazine interaction in the studied amended soils. Interestingly the addition of DOC to soil at the high application rate (S-300) reduced atrazine adsorption in this rich OM Andisol despite the LCM not raising the concentration of stable organic matter. The application of high rates of liquid manure containing DOC incurs an increased risk of pesticide leaching.     

Impact of glyphosate-tolerant soybean and glufosinate-tolerant corn production on herbicide losses in surface runoff

Residual herbicides used in the production of soybean [Glycine max (L.) Merr] and corn (Zea mays L.) are often detected in surface runoff at concentrations exceeding their maximum contaminant levels (MCL) or health advisory levels (HAL). With the advent of transgenic, glyphosate-tolerant soybean and glufosinate-tolerant corn this concern might be reduced by replacing some of the residual herbicides with short half-life, strongly sorbed, contact herbicides. We applied both herbicide types to two chiseled and two no-till watersheds in a 2-yr corn-soybean rotation and at half rates to three disked watersheds in a 3-yr corn/soybean/wheat (Triticum aestivum L.)-red clover (Trifolium pratense L.) rotation and monitored herbicide losses in runoff water for four crop years. In soybean years, average glyphosate loss (0.07%) was approximately 1/7 that of metribuzin (0.48%) and about one-half that of alachlor (0.12%), residual herbicides it can replace. Maximum, annual, flow-weighted concentration of glyphosate (9.2 microg L(-1)) was well below its 700 microg L(-1) MCL and metribuzin (9.5 microg L(-1)) was well below its 200 microg L(-1) HAL, whereas alachlor (44.5 microg L(-1)) was well above its 2 microg L(-1) MCL. In corn years, average glufosinate loss (0.10%) was similar to losses of alachlor (0.07%) and linuron (0.15%), but about one-fourth that of atrazine (0.37%). Maximum, annual, flow-weighted concentration of glufosinate (no MCL) was 3.5 microg L(-1), whereas atrazine (31.5 microg L(-1)) and alachlor (9.8 microg L(-1)) substantially exceeded their MCLs of 3 and 2 microg L(-1), respectively. Regardless of tillage system, flow-weighted atrazine and alachlor concentrations exceeded their MCLs in at least one crop year. Replacing these herbicides with glyphosate and glufosinate can reduce the occurrence of dissolved herbicide concentrations in runoff exceeding drinking water standards.     

Preferential bromide and pesticide movement to tile drains under different cropping practices

Subsurface drainage systems are useful tools to study chemical leaching in soils. Our objective was to compare the breakthrough behavior of bromide, atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-triazine) and metolachlor [2-chloro-N-(2-ethyl-6-methylphenyl)-N-(2-methoxy-1-methylethyl) acetamid] to tile drains under two fall tillage practices (conventional tillage [CT] with a moldboard plow, and reduced tillage [RT] with a chisel plow) in field plots cultivated with corn (Zea mays L.). Leachate volume were greater in RT than in CT, with no statistical differences. Soil analysis showed that bromide migrated deeper in the soil profile than both herbicides, with little tillage effect. All chemicals were detected in drainage water at the same time and followed an event-driven behavior. Tillage had no effect on atrazine and metolachlor found in drainage water, while bromide concentration peaks were higher in RT than in CT in 1999. Concentration peaks were recorded earlier for atrazine and metolachlor than for bromide. Plots of cumulative relative chemical mass (cumulative mass divided by total mass measured in drainage) as a function of cumulative drainage were mostly linear for bromide, while they were S-shaped for both herbicides. Drainage that corresponded to 50% of relative cumulative mass ranged from 40 to 55% for bromide and from 5 to 28% for both herbicides. Rapid chemical movement to tile drains suggested that preferential flow was important in both CT and RT, and that these tillage practices had little influence on this phenomena.     

Tillage system, application rate, and extreme event effects on herbicide losses in surface runoff

Conservation tillage can reduce soil loss; however, the residual herbicides normally used to control weeds are often detected in surface runoff at high levels, particularly if runoff-producing storms occur shortly after application. Therefore, we measured losses of alachlor, atrazine, linuron, and metribuzin from seven small (0.45-0.79-ha) watersheds for 9 yr (1993-2001) to investigate whether a reduced-input system for corn (Zea mays L.) and soybean [Glycine max (L.) Merr.] production with light disking, cultivation, and half-rate herbicide applications could reduce losses compared with chisel and no-till. As a percentage of application, annual losses were highest for all herbicides for no-till and similar for chisel and reduced-input. Atrazine was the most frequently detected herbicide and yearly flow-weighted concentrations exceeded the drinking water standard of 3 microg L(-1) in 20 out of 27 watershed years that it was applied. Averaged for 9 corn yr, yearly flow-weighted atrazine concentrations were 26.3, 9.6, and 8.3 microg L(-1) for no-till, chisel, and reduced-input, respectively. Similarly, flow-weighted concentrations of alachlor exceeded the drinking water standard of 2 microg L(-1) in 23 out of 54 application years and in all treatments. Thus, while banding and half-rate applications as part of a reduced-input management practice reduced herbicide loss, concentrations of some herbicides may still be a concern. For all watersheds, 60 to 99% of herbicide loss was due to the five largest transport events during the 9-yr period. Thus, regardless of tillage practice, a small number of runoff events, usually shortly after herbicide application, dominated herbicide transport.     

Spatial variability of atrazine and metolachlor dissipation on dryland no-tillage crop fields in Colorado

An area of interest in precision farming is variable-rate application of herbicides to optimize herbicide use efficiency and minimize negative off-site and non-target effects. Site-specific weed management based on field scale management zones derived from soil characteristics known to affect soil-applied herbicide efficacy could alleviate challenges posed by post-emergence precision weed management. Two commonly used soil-applied herbicides in dryland corn (Zea mays L.) production are atrazine and metolachlor. Accelerated dissipation of atrazine has been discovered recently in irrigated corn fields in eastern Colorado. The objectives of this study were (i) to compare the rates of dissipation of atrazine and metolachlor across different soil zones from three dryland no-tillage fields under laboratory incubation conditions and (ii) to determine if rapid dissipation of atrazine and/or metolachlor occurred in dryland soils. Herbicide dissipation was evaluated at time points between 0 and 35 d after soil treatment using a toluene extraction procedure with GC/MS analysis. Differential rates of atrazine and metolachlor dissipation occurred between two soil zones on two of three fields evaluated. Accelerated atrazine dissipation occurred in soil from all fields of this study, with half-lives ranging from 1.8 to 3.2 d in the laboratory. The rapid atrazine dissipation rates were likely attributed to the history of atrazine use on all fields investigated in this study. Metolachlor dissipation was not considered accelerated and exhibited half-lives ranging from 9.0 to 10.7 d in the laboratory.     

Small-scale spatial variability of atrazine and dinoseb adsorption parameters in an alluvial soil

Soil sorption processes largely control the environmental fate of herbicides. Therefore, accuracy of sorption parameters is crucial for accurate prediction of herbicide mobility in agricultural soils. A combined experimental and statistical study was performed to investigate the small-scale spatial variability of sorption parameters for atrazine and dinoseb in soils and to establish the number of samples needed to provide a value of the distribution coefficient (K(d)) next to the mean, with a given precision. The study explored sorption properties of the two herbicides in subsurface samples collected from four pits distributed along a transect of an alluvial soil; two to four samples were taken at about 30 cm apart at each sampling location. When considering all the data, the distribution coefficients were found to be normally and log-normally distributed for atrazine and dinoseb, respectively; the CVs were relatively high (close to 50% for dinoseb and 40% for atrazine). When analyzed horizon by horizon, the data revealed distribution coefficients normally distributed for both herbicides, whatever the soil layer, with lower CVs. The K(d) values were shown to vary considerably between samples collected at very short distance (a few centimeters), suggesting that taking a single soil sample to determine sorption properties through batch experiments can lead to highly unrepresentative results and to poor sorption/mobility predictions.     

Behavior of pesticide residues in agricultural soil and adjacent River Kuywa sediment and water samples from Nzoia sugarcane belt in Kenya

An inventory survey conducted to determine pesticide usage in a sub-catchment of the Nzoia sugarcane belt found a variety of pesticides used in the sub-catchment, which are reported in this paper. Analysis of soil samples from seven fallow experimental field plots left uncultivated for various periods from 3 to 96?months after cultivation with pesticide application indicated persistence of high concentrations of pesticide residues in the soil, with estimated soil half-lives (in years) ranging from 0.72 to 57.75 for organochlorines and from 1.13 to 8.25 for herbicides. The mean water concentrations (in ??g/L) of the pesticide residues in River Kuywa, which flows through the Nzoia Nucleus Estate sugarcane farms, ranged from 0.12 (lindane) to 1.36 (p,p??-DDT) for organochlorines and from 0.14 (atrazine) to 1.75 (diuron) for herbicides during the heavy rains period in August 2008 while the mean sediment concentrations (in ??g/g) ranged from 0.28 (lindane) to 1.87 (endrin) for organochlorines and 0.39 (hexazinone) to 4.61 (alachlor) for herbicides. The mean concentrations of residues in water during the light rain period in December 2008 ranged from 0.17 (p,p??-DDT) to 0.71 (aldrin) for organochlorines and 0.01 (atrazine) to 1.74 (alachlor) for herbicides while the sediment concentrations ranged from 0.38 (p,p??-DDT) to 1.145 (aldrin) for organochlorines and 0.74 (atrazine) to 1.98 (alachlor) for herbicides. Although DDT, aldrin, dieldrin, and endrin were not reported in the survey, their presence in the fallow experimental field plot soils and in River Kuywa water and sediment could indicate previous application, lack of recorded data or illegal usage since 1997 when they were banned. Notably, the concentrations of alachlor, diuron, cypermethrin, and hexazinone in the water column were substantial indicating their extensive usage and residual persistence in the sub-catchment, with subsequent wash-off and leaching into River Kuywa. The concentration levels of some of the individual pesticides exceeded the EU limit requirements for drinking water and indicated potential risk to humans and cattle if the water is used without treatment.     

Effects of soil phosphorus status on environmental risk assessment of glyphosate and glufosinate-ammonium

The increased use of herbicides poses a risk to the aquatic environment. Easy and economical methods are needed to identify the fields where specific environment protection measures are needed. Phosphorus (P) and organophosphorus herbicides compete for the same adsorption sites in soil. In this study the relationship between P obtained in routine Finnish agronomic tests (acid ammonium acetate [P(AC)]) and adsorption of glyphosate and glufosinate-ammonium was investigated to determine whether P(AC) values could be used in the risk assessment. The adsorption of glyphosate ((N-(phosphonomethyl)glycine) and glufosinate-ammonium (2-amino-4-(hydroxymethylphosphinyl)butanoic acid) was studied in a clay and a sandy loam soil enriched with increasing amounts of P added as potassium dihydrogen phosphate. Desorption was also determined for some P-enriched soil samples. The adsorption of both herbicides diminished with increasing P(AC) value. The correlations between Freundlich adsorption coefficients obtained in the adsorption tests and P(AC) were nonlinear but significant (r > 0.98) in both soils. The exponential models of the relationship between soil P(AC) values and glyphosate adsorption were found to fit well to an independent Finnish soil data set (P < 0.1 for glyphosate and P < 0.01 for glufosinate-ammonium). The desorption results showed that glufosinate-ammonium sorption is not inversely related to soil P status, and the high correlation coefficients obtained in the test of the model were thus artifacts caused by an abnormal concentration of exchangeable potassium in soil. The solved equations are a useful tool in assessing the leaching risks of glyphosate, but their use for glufosinate-ammonium is questionable.     

Sorption-desorption of carbamazepine from irrigated soils

Th anti-seizure medication carbamazepine is often found in treated sewage effluent and environmental samples. Carbamazepine has been shown to be very persistent in sewage treatment, as well as ground water. Due to environmental persistence, irrigation with sewage effluent could result in carbamazepine contamination of surface and ground water. To determine the potential for leaching of carbamazepine, a series of adsorption and desorption batch equilibrium experiments were conducted on irrigated soils. It was found that carbamazepine adsorption to biosolid-amended (T) soils had a KD of 19.8 vs. 12.6 for unamended soil. Based on adsorption, carbamazepine leaching potential would be categorized as low. During desorption significant hysteresis was observed and KD increased for both soils. Desorption isotherms also indicate a potential for irreversibly bound carbamazepine in the T soil. Results indicate that initial removal of carbamazepine via adsorption from irrigation water is significant and that desorption characteristics would further limit the mobility of carbamazepine through the soil profile indicating that carbamazepine found in sewage effluent used for irrigation has a low leaching potential.     

Time Series Analysis of Nebraska Daily Rainfall Data to Simulate Atrazine Runoff1

Abstract: Measured atrazine concentrations in Nebraska surface water have been shown to exceed water‐quality standards, posing risks to humans and to the ecosystem. To assess this risk, atrazine runoff was simulated at the field‐scale in Nebraska based on the pesticide component of the AGNPS model. This project’s objective was to determine the frequency that the atrazine concentration at the field outlet exceeded three different atrazine water‐quality criteria. The simulation was conducted for different farm management practices, soil moisture conditions, and five Nebraska topographic regions. If the criteria were exceeded, a risk to the drinking water consumer or freshwater aquatic life was hypothesized to exist. Three pesticide fate and transport processes were simulated with the model. Degradation was simulated using first‐order kinetics. Adsorption/desorption was modeled assuming a linear soil‐water partitioning coefficient. Advection (runoff) was based primarily on the USDA‐NRCS curve number method. Daily rainfall from the National Weather Service was used to compute the soil moisture conditions for the 1985‐2000 growing seasons. After each runoff event, the pesticide runoff concentration was compared with each of the three atrazine water‐quality criteria. The results show that environmental receptors (i.e., freshwater aquatic species) are exposed to unacceptable atrazine runoff concentrations in 20‐50% of the runoff events.     

Spatial distribution of enhanced atrazine degradation across northeastern Colorado cropping systems

Reports of enhanced atrazine degradation and reduced residual weed control have increased in recent years, sparking interest in identifying factors contributing to enhanced atrazine degradation. The objectives of this study were to (i) assess the spatial distribution of enhanced atrazine degradation in 45 commercial farm fields in northeastern Colorado (Kit Carson, Larimer, Logan, Morgan, Phillips, and Yuma counties) where selected cultural management practices and soil bio-chemo-physical properties were quantified; (ii) utilize Classification and Regression Tree (CART) Analysis to identify cultural management practices and (or) soil bio-chemophysical attributes that are associated with enhanced atrazine degradation; and (iii) translate our CART Analysis into a model that predicts relative atrazine degradation rate (rapid, moderate, or slow) as a function of known management practices and (or) soil properties. Enhanced atrazine degradation was widespread within a 300-km radius across northeastern Colorado, with approximately 44% of the fields demonstrating rapid atrazine degradation activity (laboratory-based dissipation time halflife [DT50] < 3 d). The most rapid degradation rates occurred in fields that received the most frequent atrazine applications. Classification and Regression Tree Analysis resulted in a prediction model that correctly classified soils with rapid atrazine DT50 80% of the time and soils with slow degradation (DT50 > 8 d) 62.5% of the time. Significant factors were recent atrazine use history, soil pH, and organic matter content. The presence/absence of atzC polymerase chain reaction (PCR) product was not a significant predictor variable for atrazine DT50. In conclusion, enhanced atrazine degradation is widespread in northeastern Colorado. If producers know their atrazine use history, soil pH, and OM content, they should be able to identify fields exhibiting enhanced atrazine degradation using our CART Model.     

Imazaquin adsorbed on pillared clay and crystal violet-montmorillonite complexes for reduced leaching in soil

Ground water pollution due to herbicide leaching has become a serious environmental problem. Imazaquin [2-(4-isopropyl-4-methyl-5-oxo-2-imidazolin-2-yl)quinoline-3-carboxylic acid] is an herbicide used to control broadleaf weeds in legume crops. Imazaquin is negatively charged at the basic pH of calcareous soils and exhibits high leaching potential in soils. Our aim was to design formulation of imazaquin to reduce herbicide leaching. Imazaquin sorption on pillared clay (PC) and crystal violet (CV)-montmorillonite complexes was studied. The CV-montmorillonite complexes become positively charged with adsorption of CV above the cation exchange capacity (CEC) of montmorillonite, and thus can sorb imazaquin. The Langmuir equation provides a good fit to isotherms of imazaquin sorption on PC and CV-montmorillonite complexes, but for charged complexes an equation that combines electrostatics with specific binding was preferred. Maximal imazaquin sorption was 17.3 mmol kg-1 for PC and 22.2 mmol kg-1 for CV-montmorillonite complexes. The extents of imazaquin desorption into water were 21% for PC and 5% for CV-clay complexes. The presence of anions decreased imazaquin sorption on both sorbents in the sequence phosphate > acetate > sulfate. Reduction of imazaquin sorption by the anions and the extent of its desorption in electrolyte solutions were higher for PC than for CV-clay complexes. Leaching of imazaquin from CV-montmorillonite formulations through soil (Rhodoxeralf) columns was two times less than from PC formulations and four times less than that of technical imazaquin. The CV-montmorillonite complexes at a loading above the CEC appear to be suitable for preparation of organo-clay-imazaquin formulations that may reduce herbicide leaching significantly.