Performance study on evacuated tubular collector coupled solar still in West Texas climate

Experimental study was performed on a single basin active solar distillation system augmented with a solar collector using evacuated solar tubes. Field tests were conducted over several days under the climatic conditions of West Texas to evaluate the effect evacuated solar tubes have on the daily distillate yield rate. To investigate the feasibility of the solar tubes, active and passive solar stills with and without exterior insulation were examined. The maximum daily production rate for the active distillation system using evacuated solar tubes and the passive distillation system was 3.6 and 1.4 kg/m²day, respectively. The results showed the augmentation of the still with evacuated solar tubes increased its production capacity by a factor of 2.63. It also increased the maximum temperature of the water in the still basin by at least 20 °C. Economic analysis shows that it is feasible to use evacuated tubular collector coupled solar still as an alternative means for reclaiming water in farmlands with a payback period of approximately 6 years.     

Enhanced solar still productivity using transparent walls with an integral trough and organic porous absorber material

This experimental work has been conducted to compare the performance of the modified stills with that of the conventional still. Three modified stills (S1, S2, and S3) and conventional still (S4) were fabricated, each with 0.5 m² of the basin area. S1 and S3 had transparent double glass walls with air in between acting as insulation, whereas S2 has a single transparent wall. S4 has insulated plywood walls painted black from inside. A mixture of coco peat and charcoal was used in S1, S2, and S3, whereas there was no basin material for S4. Experiments were conducted by changing the water quantity in the solar still ranging from 5 to 10 kg. Maximum distillate output of 5.46 l/m²-d was obtained for S2, whereas it was 3.80 l/m²-d for S4 for an average solar radiation intensity of 675 W/m² (24.3 MJ/m²-d). Use of transparent walls with troughs to collect condensate increased the condenser area by 78.4%. The distillate water cost per liter was estimated as Rs. 0.86 (0.013 US$) and Rs. 1.61 (0.025 US$) for S2 and S4, respectively. Energy payback time for S2 was estimated as 4 months. Theoretical and experimental values showed that there is a significant loss of incoming solar radiation due to wall shadow.     

Performance of a small-scale solar-powered adsorption cooling system

In this study, an experimental investigation on the performance of a small-scale residential-size solar-driven adsorption (silica gel-water) cooling system that was constructed at Assiut University campus, Egypt is carried out. As Assiut area is considered as hot, arid climate, field tests for performance assessment of the system operation during the summer season are performed under different environmental operating conditions. The system consists of an evacuated tube with a reflective concentration parabolic surface solar-collector field with a total area of 36 m², a silica gel-water adsorption chiller of 8 kW nominal cooling capacity, and hot and cold water thermal storage tanks of 1.8 and 1.2 m³ in volume, respectively. The results of summer season field test show that under daily solar insolation varying from 21 to 27 MJ/m², the solar collectors employed in the system had high and almost constant thermal efficiency. The daily solar-collector efficiency during the period of system operation ranged from about 50% to 78%. The adsorption chiller performance shows that the chiller average daily coefficient of performance (COP) was 0.41 with the average cooling capacity of 4.4 kW when the cooling-water and chilled-water temperatures were about 31°C and 19°C, respectively. As the chiller cooling water is cooled by the cooling tower in the hot arid area, the cooling water is at a higher temperature than the design point of the chiller. Therefore, an experiment was carried out using the city water for cooling. The results show that an enhancement in the chiller COP by 40% and the chilling power by 17% has been achieved when the city water was 27.7°C.     

Experimental investigation of a solar water distillation-cum-drying unit

In this communication, a new design of solar-energy-based water distillation cum drying unit with parabolic reflector has been designed, fabricated, and tested. Bitter gourd and potato slices are chosen as a drying commodity. Thermal performance of the developed system has been evaluated based on the experimental results and using linear regression analysis. Heat transfer coefficients (convective, evaporative, and radiative) for solar distillation system have been observed to be 2.48–4.09, 13.25–52.38, and 8.75–9.66 W/m²°C, respectively. Overall thermal efficiency and exergy efficiency for the distillation system has been found to be 18.77% and 1.2%, respectively. The convective heat transfer coefficient for potato slices are observed higher for initial hours and decreases as the day progresses. The average convective heat transfer coefficients for bitter gourd and potato slices have been observed as 2.18 and 5.04 W/m²°C, respectively. Experimental error in terms of percent uncertainty for bitter gourd and potato slices are found to be 42.93% and 37.06%, respectively. The present design of solar distillation and drying in a single unit could be beneficial for the development of remote, arid, and rural areas.     

Thermal Characteristics of Stormwater Runoff from Asphalt and Sod Surfaces1

Abstract: Urban impervious surfaces absorb and store thermal energy, particularly during warm summer months. During a rainfall/runoff event, thermal energy is transferred from the impervious surface to the runoff, causing it to become warmer. As this higher temperature runoff enters receiving waters, it can be harmful to coldwater habitat. In an urban watershed, impervious asphalt surfaces (roads, parking lots, and driveways) and pervious residential lawns comprise a significant portion of the watershed area. A paired asphalt‐turfgrass sod plot was constructed to compare the thermal runoff characteristics between asphalt and turfgrass sod surfaces, to identify meteorological variables that influence these thermal characteristics, and to evaluate evaporative heat loss for runoff from asphalt surfaces. Rainfall simulations were conducted during the summers of 2004 and 2005 under a range of climatic conditions. Asphalt surface temperatures immediately prior to rainfall simulations averaged 43.6°C and decreased an average of 12.3°C over 60 min as rain cooled the surface. In contrast, presimulation sod surface temperatures averaged only 23.3°C and increased an average of 1.3°C throughout the rainfall events. Heat transferred from the asphalt to the runoff resulted in initial asphalt runoff temperatures averaging 35.0°C that decreased by an average of 4.1°C at the end of the event. Sod runoff temperatures averaged only 25.5°C and remained fairly constant throughout the simulations. Multivariable regression equations were developed to predict (1) average asphalt surface temperature (R² = 0.90) and average asphalt runoff temperature (R² = 0.92) as a function of solar radiation, rain temperature, and wind speed, and (2) average sod surface temperature (R² = 0.85) and average sod runoff temperature (R² = 0.94) as a function of solar radiation, rain temperature, rain intensity, and wind speed. Based on a heat balance analysis, existing evaporation equations developed from studies on lakes were not adequate to predict evaporation from runoff on a heated impervious surface. The combined heat from the asphalt and sod plots was an average of 38% less than the total heat had the total area consisted solely of asphalt.     

Experimental study of new solar air heater design

The suitable design is the most important key to a cost-effective solar air heater. Although there are many techniques that have been proposed to improve the solar air heaters’ performance by means of different turbulence promoters, they cannot ensure a compromise between the cost and the effectiveness. The aim of this study is to find simple and tolerable solution to get rid of the inconvenience resulting from the widely adopted heat-transfer-enhancement techniques by providing an optimized solar air heater design. The proposed design consists of a slightly curved smooth flow channel with an absorber plate of convex shape. A prototype of a curved solar air heater of 1.28 m² collector area was built and tested under summer outdoor conditions in Biskra (Algeria). The performance was evaluated in terms of thermal and effective efficiency for mass flow rates of 0.0172, 0.029, and 0.0472 kg/sm². It is observed that the overall efficiency of this solar air heater is considerably higher in comparison with the efficiency range of the conventional smooth flat plate heaters reported in the literature for similar operating conditions.     

Real‐Time Analysis of Energy Generation of a Photovoltaic System Installed in the City of Lajeado,Rio Grande do Sul

Considering successive and costly increases in electricity rates, this article evaluates the generation of electricity from a photovoltaic system using solar energy, a renewable source. The solar photovoltaic system is installed at UNIVATES University Center, a public university in the state of Rio Grande do Sul, Brazil, and it is also connected to the electrical grid. Data related to the climatic conditions of the location, such as incident solar radiation, rainfall, and mean temperature, were obtained during the system's evaluation period and used along with bibliographic research on similar systems installed in southern Brazil. Our study quantified the energy produced over one calendar year (2014) and related it to the climatic variables and the conversion efficiency achieved by the system's photovoltaic modules. Our results show that there is both a strong relationship between the production of energy and climatic conditions and that the city, Lajeado, and the Brazilian state of Rio Grande do Sul, have good potential to supply energy using photovoltaic systems connected to the electrical grid. The horizontal global solar radiation average obtained in the study location was 4.14 kilowatts per square meter per day (kWh/m²/day), and the average monthly production of energy reached 243.93 kWh/m²/month, with a total of 2,927.10 kWh produced in 2014, achieving a monthly average conversion efficiency of 11.07%. This conversion efficiency is close to the value of 12.6% obtained in 2013 in a similar study of the same solar photovoltaic system conducted over a shorter time period.     

Comparative study on performances of a heat-pipe PV/T system and a heat-pipe solar water heating system

The heat-pipe solar water heating (HP-SWH) system and the heat-pipe photovoltaic/thermal (HP-PV/T) system are two practical solar systems, both of which use heat pipes to transfer heat. By selecting appropriate working fluid of the heat-pipes, these systems can be used in the cold region without being frozen. However, performances of these two solar systems are different because the HP-PV/T system can simultaneously provide electricity and heat, whereas the HP-SWH system provides heat only. In order to understand these two systems, this work presents a mathematical model for each system to study their one-day and annual performances. One-day simulation results showed that the HP-SWH system obtained more thermal energy and total energy than the HP-PV/T system while the HP-PV/T system achieved higher exergy efficiency than the HP-SWH system. Annual simulation results indicated that the HP-SWH system can heat the water to the available temperature (45°C) solely by solar energy for more than 121 days per year in typical climate regions of China, Hong Kong, Lhasa, and Beijing, while the HP-PV/T system can only work for not more than 102 days. The HP-PV/T system, however, can provide an additional electricity output of 73.019 kWh/m², 129.472 kWh/m², and 90.309 kWh/m² per unit collector area in the three regions, respectively.     

Impacts of Climate Change on Hydrology and Water Resources in the Boise and Spokane River Basins1

Jin, Xin and Venkataramana Sridhar, 2012. Impacts of Climate Change on Hydrology and Water Resources in the Boise and Spokane River Basins. Journal of the American Water Resources Association (JAWRA) 48(2): 197‐220. DOI: 10.1111/j.1752‐1688.2011.00605.x Abstract: In the Pacific Northwest, warming climate has resulted in a lengthened growing season, declining snowpack, and earlier timing of spring runoff. This study characterizes the impact of climate change in two basins in Idaho, the Spokane River and the Boise River basins. We simulated the basin‐scale hydrology by coupling the downscaled precipitation and temperature outputs from a suite of global climate models and the Soil and Water Assessment Tool (SWAT), between 2010 and 2060 and assess the impacts of climate change on water resources in the region. For the Boise River basin, changes in precipitation ranged from ?3.8 to 36%. Changes in temperature were expected to be between 0.02 and 3.9°C. In the Spokane River region, changes in precipitation were expected to be between ?6.7 and 17.9%. Changes in temperature appeared between 0.1 and 3.5°C over a period of the next five decades between 2010 and 2060. Without bias‐correcting the simulated streamflow, in the Boise River basin, change in peak flows (March through June) was projected to range from ?58 to +106 m³/s and, for the Spokane River basin, the range was expected to be from ?198 to +88 m³/s. Both the basins exhibited substantial variability in precipitation, evapotranspiration, and recharge estimates, and this knowledge of possible hydrologic impacts at the watershed scale can help the stakeholders with possible options in their decision‐making process.     

The global solar radiation estimation and analysis of solar energy: Case study for Osmaniye,Turkey

This paper investigates the prediction of solar radiation model and actual solar energy in Osmaniye, Turkey. Four models were used to estimate using the parameters of sunshine duration and average temperature. In order to obtain the statistical performance analysis of models, the coefficient of determination (R²), mean absolute percentage error (MAPE), mean absolute bias error (MABE), and root mean square error (RMSE) were used. Results obtained from the linear regression using the parameters of sunshine duration and average temperature showed a good prediction of the monthly average daily global solar radiation on a horizontal surface. In order to obtain solar energy, daily and monthly average solar radiation values were calculated from the five minute average recorded values by using meteorological measuring device. As a result of this measurement, the highest monthly and yearly mean solar radiation values were 698 (April in 2013) and 549 (2014 year) W/m² respectively. On an annual scale the maximum global solar radiation changes from 26.38 MJ/m²/day by June to 19.19 MJ/m²/day by September in 2013. Minimum global solar radiation changes from 14.05 MJ/m²/day by October to 7.20 MJ/m²/day by January in 2013. Yearly average energy potential during the measurement period was 16.53 MJ/m²/day (in 2013). The results show that Osmaniye has a considerable solar energy potential to produce electricity.     

Optimisation of rainwater tank design from large roofs: A case study in Melbourne, Australia

Rainwater tanks for larger roof areas need optimisation of tank size, which is often not carried out before installation of these tanks. This paper presents a case study of rainwater tank evaluation and design for large roof areas, located in Melbourne, Australia, based on observed daily rainfall data representing three different climatic regimes (i.e. dry average, and wet years). With the aim of developing a comprehensive Decision Support Tool for the performance analysis and design of rainwater tanks, a simple spreadsheet based daily water balance model is developed using daily rainfall data, contributing roof area, rainfall loss factor, available storage volume, tank overflow and irrigation water demand. In this case study, two (185 m³ and 110 m³) underground rainwater tanks are considered. Using the developed model, effectiveness of each tank under different climatic scenarios are assessed. The analysis shows that both the tanks are quite effective in wet and average years, however less effective in dry years. A payback period analysis of the tanks is preformed which reveals that the total construction cost of the tanks can be recovered within 15-21 years time depending on tank size, climatic conditions and future water price increase rates. For the tanks, a relationship between water price increase rates and payback periods is developed. The study highlights the need for detailed optimisation and financial analysis for large rainwater tanks to maximise the benefits.     

Regional and Local Scale Modeling of Stream Temperatures and Spatio-Temporal Variation in Thermal Sensitivities

Understanding variation in stream thermal regimes becomes increasingly important as the climate changes and aquatic biota approach their thermal limits. We used data from paired air and water temperature loggers to develop region-scale and stream-specific models of average daily water temperature and to explore thermal sensitivities, the slopes of air–water temperature regressions, of mostly forested streams across Maryland, USA. The region-scale stream temperature model explained nearly 90 % of the variation (root mean square error = 0.957 °C), with the mostly flat coastal plain streams having significantly higher thermal sensitivities than the steeper highlands streams with piedmont streams intermediate. Model R ² for stream-specific models was positively related to a stream’s thermal sensitivity. Both the regional and the stream-specific air–water temperature regression models benefited from including mean daily discharge from regional gaging stations, but the degree of improvement declined as a stream’s thermal sensitivity increased. Although catchment size had no relationship to thermal sensitivity, steeper streams or those with greater amounts of forest in their upstream watershed were less thermally sensitive. The subset of streams with three or more summers of temperature data exhibited a wide range of annual variation in thermal sensitivity at a site, with the variation not attributable to discharge, precipitation patterns, or physical attributes of streams or their watersheds. Our findings are a useful starting point to better understand patterns in stream thermal regimes. However, a more spatially and temporally comprehensive monitoring network should increase understanding of stream temperature variation and its controls as climatic patterns change.     

Global solar radiation and energy yield estimation from photovoltaic power plants for small loads

Daily global solar radiation on a horizontal surface and duration of sunshine hours have been determined experimentally for five meteorological stations in Saudi Arabia, namely, Abha, Al-Ahsa, Al-Jouf, Al-Qaisumah, and Wadi Al-Dawaser sites. Five-years of data covering 1998–2002 period have been used. Suitable Angstrom models have been developed for the global solar radiation estimation as a function of the sunshine duration for each respective sites. Daily averages of monthly solar PV power outputs have been determined using the Angstrom models developed. The effect of the PV cell temperature on the PV efficiency has been considered in calculating the PV power output. The annual average PV output energy has been discussed in all five sites for small loads. The minimum and maximum monthly average values of the daily global solar radiation are found to be 12.09 MJ/m²/d and 30.42 MJ/m²/d for Al-Qaisumah and Al-Jouf in the months of December June, respectively. Minimum monthly average sunshine hours of 5.89 hr were observed in Al-Qaisumah in December while a maximum of 12.92 hr in Al-Jouf in the month of June. Shortest range of sunshine hours of 7.33–10.12 hr was recorded at Abha station. Minimum monthly average Solar PV power of 1.59 MJ/m²/day was obtained at Al-Qaisumah in the month of December and a maximum of 3.39 MJ/m²/day at Al-Jouf in June. The annual PV energy output was found to be 276.04 kWh/m², 257.36 kWh/m², 256.75 kWh/m², 245.44 kWh/m², and 270.95 kWh/m² at Abha, Al-Ahsa, Al-Jouf, Al-Qaisumah, and Wadi Al-Dawaser stations, respectively. It is found that the Abha site yields the highest solar PV energy among the five sites considered.     

Investigation of activated carbon/ethanol for low temperature adsorption cooling

Commercially available adsorption cooling systems use water/silica gel, water/zeolite and ammonia/ chloride salts working pairs. The water-based pairs are limited to work above 0°C due to the water high freezing temperature, while ammonia has the disadvantage of being toxic. Ethanol is a promising refrigerant due to its low freezing point (161 K), nontoxicity, zero ozone depletion, and low global warming potential. Activated carbon (AC) is a porous material with high degree of porosity (500–3000 m²/g) that has been used in wide range of applications. Using Dynamic Vapour Sorption (DVS) test facility, this work characterizes the ethanol adsorption of eleven commercially available activated carbon materials for cooling at low temperature of ?15°C. DVS adsorption results show that Maxsorb has the best performance in terms of ethanol uptake and adsorption kinetics compared to the other tested materials. The Maxsorb/ethanol adsorption process has been numerically modeled using computational fluid dynamics (CFD) and simulation results are validated using the DVS experimental measurements. The validated CFD simulation of the adsorption process is used to predict the effects of adsorbent layer thickness and packing density on cycle uptake for evaporating temperature of ?15°C. Simulation results show that as the thickness of the Maxsorb adsorbent layer increases, its uptake decreases. As for the packing density, the amount of ethanol adsorbed per plate increases with the packing density reaching maximum at 750 kg/m³. This work shows the potential of using Maxsorb/ethanol in producing low temperature cooling down to ?15°C with specific cooling energy reaching 400 kJ/kg.     

REGIONALIZATION AND PREDICTION OF ANNUAL FLOODS IN THE FRASER RIVER CATCHMENT,BRITISH COLUMBIA1

A method of predicting probability distributions of annual floods is presented and is applied to the Fraser River catchment of British Columbia. The Gumbel distribution is found to adequately describe the observed flood frequency data. Using the estimated Gumbel parameters, discriminant analysis is performed to separate basins into flood regions. Within each region, regression analysis is used to relate physiographic and climatic variables to the means and standard deviations of the annual flood series. The regression equations are applied to four test basins and the results indicate that the method is suitable for an estimation of annual floods.     

Thermal energy storage and thermodynamic properties of (E)-3-m-tolylbut-2-enoic acid as a medium temperature phase change material

Phase change materials (PCMs) that can store and release heat energy over the temperature range from 363 to 393 K are crucial for solar absorption cooling, and it is worthy to seek new solid-liquid PCMs candidates that melt and crystallize in this temperature range. In this paper, (E)-3-m-tolylbut-2-enoic acid (mTBEA) was applied as a PCM candidate. Its thermal energy storage properties and thermal stability were systematically investigated. The results showed that mTBEA melted at 382.9 ± 0.5 K and crystallized at about 364 K, with a melting enthalpy (Δ_fusH) of 138.4 ± 6.9 J g^?1 and showed good long-term cyclic stability and thermal stability. The supercooling of mTBEA was stabilized at about 20 K, indicating that the conservation condition of melted mTBEA could be simple. In addition, the melted mTBEA could release all the absorbed thermal energy upon crystallizing. Besides, mTBEA exhibited good thermal stability for it to be applied as PCM. Hence, mTBEA is a promising PCM candidate for solar absorption cooling. Furthermore, the heat capacity of mTBEA was measured by modulated temperature differential scanning calorimetry (MTDSC) over the temperature range from 198.15 to 431.15 K, and the molar thermodynamic functions, [H_T-H_298.15]_m and [S_T-S_298.15]_m, were calculated based on the fitted molar heat capacity data.     

GENERATION OF SYNTHETIC AND MISSING CLIMATIC DATA FOR PUERTO RICO1

ABSTRACT: Climatic data such as temperature, solar radiation, relative humidity, and wind speed have been widely used to estimate evapotranspiration. Moat of the solar radiation data and portions of the relative humidity data are either not available or missing from the records in Puerto Rico. Depending upon the availability and data characteristics of records, three methods (including a regression technique, an averaging of historical data, and a regional average) were used to generate missing data, and a time series analysis was used to synthesize a series of climatic data. The limitations and applicability of each method are discussed. The results showed that the time series analysis method can be successfully used to synthesize a series of monthly solar radiations for several stations. The regression technique and the regional average can be successfully applied to generate missing monthly solar radiation data. The regression technique and the averaging of historical data have been satisfactorily used to interpolate missing monthly relative humidity. The explained variance (R²) varied from 0.68 to 0.88, which are both significant at the 0.05 level of significance.     

Evaluation of various global solar radiation models for Nigeria

This study assessed the performance of six solar radiation models. The objective was to determine the most accurate model for estimating global solar radiation on a horizontal surface in Nigeria. Twenty-two years meteorological data sets collected from the Nigerian Meteorological agency and the National Aeronautics and Space Administration for the three regions, covering the entire climatic zones in Nigeria were utilized for calibrating and validating the selected models for Nigeria. The accuracy and applicability of various models were determined for three locations (Abuja, Benin City, and Sokoto), which spread across Nigeria using seven viable statistical indices. This study found that the estimation results of considered models are statistically significant at the 95% confidence level, but their accuracy varies from one location to another. However, the multivariable regression relationship deduced in terms of sunshine ratio, air temperature ratio, maximum air temperature, and cloudiness performs better than other relationships. The multivariable relationship has the least root mean square error and mean absolute bias error, not exceeding 1.0854 and 0.8160 MJ m^?2 day^?1, respectively, and monthly relative percentage error in the range of ± 12% for the study areas.     

Comparison of energy produced from waste by removing its different components: A case study of the waste landfill in Tehran

In developing and populated cities such as Tehran, a massive amount of municipal solid waste (MSW), both wet and dry, is transferred to landfills daily. Combustion is one of the most common methods of using mixed waste energy from the past to the present. The Dulong formula is widely used to calculate the energy released from MSW combustion. According to the constituent components of Tehran MSW, removing food waste leads to an increase in energy potential, which will be a suitable condition for energy production. In this work, the energy derived from the combustion of mixed and separated dry MSW generated in Tehran was calculated using the experimental Dulong formula and tables in Integrated Solid Waste Management (Tchobanoglous et al. 1993, McGraw‐Hill). The Dulong formula indicates that the use of Tehran mixed MSW (without separating materials for recycling) as a fuel source yields 8,966.40 KJ/kg while the use of Tchobanoglous et al. (1993) tables can generate 8,236 kJ/kg. By removing food waste and recyclable materials, the potential of energy production changes to 22,047 kJ/kg using the Dulong formula and 16,207 kJ/kg and the Tchobanoglous et al. (1993) tables. It indicates increase by 1.46 times and 46%, respectively. Regarding the 200‐ton capacity of the Tehran waste incinerator, the Dulong formula indicated generation of 4,409 MJ/day energy, and the Tchobanoglous et al. table presents 3,241 MJ/day. Therefore, considering that Tehran generates more than 4,000 tons of reject waste daily, it can easily be converted to energy rather than landfilled. This can alleviate the problem of buying land and construction of landfills and leachate generation.     

Thermal analysis of tilted wick solar distillation-cum-drying system

The performance of the designed tilted wick solar water distillation-cum-drying unit has been tested at water flow rates of 50 and 65 ml/min in the distillation unit. Effect of water flow rates on the heat transfer coefficients of distillation and drying unit for drying ginger has been evaluated. The energy and exergy efficiency of the distillation system have also been evaluated. Average distillates of 2.36 and 2.2 l/m² were collected from the tilted wick solar still at flow rates of 50 and 65 ml/min, respectively. Large variation in convective and evaporative heat transfer coefficients of distillation unit has been observed at given water flow rates. Water flow rate in the distillation unit significantly affects the performance of the drying unit. Average convective heat transfer coefficients of 6.56 and 3.75 W/m^{2 o}C have been observed for drying ginger at flow rates of 50 and 65 ml/min, respectively. Energy and exergy efficiency of the distillation unit have been found to be nearly 19% and 0.9%, respectively. Experimental uncertainty has also been evaluated for distillation and drying units. The distillate cost for the developed distillation-cum-drying unit is calculated as $0.03729/l along with dried ginger of about 2.5 kg/m²/day.