Investigation of the association between pesticide exposure and the prevalence of type 2 diabetes in Shahedieh population in Yazd

Environmental Science and Pollution Research - This study aimed to investigate the effect of exposure to pesticides and the prevalence of type 2 diabetes (T2D). In a cross-sectional study with a...     

Usage of polystyrene disposable food dishes in the lightweight concrete making

The increasing use and subsequent accumulation of polystyrene containers has triggered a substantial environmental problem. This study investigated using varied percentages of solid waste polystyrene disposable food dishes in the production of lightweight concrete samples with 350 kilograms per cubic meter (kg/m³) of cement and a density of 1,300 kg/m³. The polystyrene disposable dishes were ground into beads of 0–3 millimeters (mm) and 3–6 mm in size. First, the characteristics of Type II Portland cement, polystyrene, and aggregates were examined. The following characteristics of concrete using ASTM International and British Standards Institution standards were tested: slump, compressive strength, ability to resist chloride ion penetration, and resistance of concrete to rapid freezing and thawing cycles. Scanning electron microscopy (SEM) and energy dispersive X‐ray spectroscopy analytical techniques were also used. The slump of samples varied between 40 and 70 mm and was not dependent on either the polystyrene percentage or the size of the polystyrene beads in the concrete samples (p‐value > .05). The compressive strength of the concrete samples after 90 days of curing, and using different percentages of polystyrene, varied between 96 and 113 kilograms per square centimeter (kg/cm²). The resistance of the samples to the freezing and thawing cycle and chloride ion penetration were affected unfavorably by the presence of the polystyrene. The SEM technique indicated that concrete samples containing 15% and 25% polystyrene had denser crystals and less void than concrete samples with 40% and 55% polystyrene.     

Involvement of mitochondrial-mediated caspase-3 activation and lysosomal labilization in acrylamide-induced liver toxicity

Acrylamide (ACR) is a chemical frequently used in both industrial and synthetic processes and may be produced during food processing. ACR at very high concentrations is postulated to exert its toxicity through the stimulation of an oxidative stress. ACR in excessive doses induces the central nervous system, reproduction, and genetic toxicity. However, ACR effects on the liver, a major organ of drug metabolism, have not been adequately explored. In addition, the role of mitochondria in an ACR-mediated hepatotoxicity is still unclear. The aim of this study was to investigate the cytotoxic mechanisms attributed to ACR using isolated rat hepatocytes. Hepatocytes were isolated by the collagenase perfusion method and incubated with an EC50_2hr concentration of ACR for 3 hr. The EC50_{2 hr} of ACR on isolated rat hepatocytes was determined to be 1 mM. Based on our results, hepatocytes cytotoxicity of ACR (1 mM) was mediated by a reactive oxygen species formation and lipid peroxidation. Incubation of hepatocytes with ACR produced rapid hepatocyte glutathione depletion which is another marker of the cellular oxidative stress. ACR cytotoxicity was also associated with mitochondrial injury as evidenced by the decline of mitochondrial membrane potential and lysosomal membrane leakiness. Our results also showed that ACR induced caspase-3 activation, the final mediator of apoptosis signaling. These findings contribute to a better understanding underlying mechanisms involved in ACR hepatotoxicity originating from the oxidative stress and ending in mitochondrial/lysosomal damage and cell death signaling.     

The effect of greenhouse vegetation coverage and area on the performance of an earth-to-air heat exchanger for heating and cooling modes

The underground temperature at a depth of about 3–4 m is almost constant all the year round. In summer, the underground temperature is lower than the ambient temperature, but in winter it is vice versa. This potentiality is considered for greenhouse cooling and heating by using an earth-to-air heat exchanger (EAHE). This paper considers the effects of two parameters as independent variables including the area of greenhouse and the percentage of vegetation coverage inside the greenhouse on the performance of an EAHE system during both cooling and heating modes. The inside temperature, the thermal energy exchange and the coefficient of performance (COP) of the system were considered as dependent variables. The results showed that both greenhouse area and the percentage of vegetation coverage inside the greenhouse had significant effects on the performance of the EAHE system during both cooling and heating modes. However, the COP of the EAHE system was higher in the cooling mode (4.32) than during the heating mode (1.01). The percentage of vegetation coverage negatively affected the performance of the EAHE system in the cooling mode. However, the performance of the EAHE system improved with the increase in the percentage of vegetation coverage during the heating mode.     

Objective approach for analysis of noise source characteristics and acoustic conditions in noisy computerized embroidery workrooms

It is highly important to analyze the acoustic properties of workrooms in order to identify best noise control measures from the standpoint of noise exposure limits. Due to the fact that sound pressure is dependent upon environments, it cannot be a suitable parameter for determining the share of workroom acoustic characteristics in producing noise pollution. This paper aims to empirically analyze noise source characteristics and acoustic properties of noisy embroidery workrooms based on special parameters. In this regard, reverberation time as the special room acoustic parameter in 30 workrooms was measured based on ISO 3382-2. Sound power quantity of embroidery machines was also determined based on ISO 9614-3. Multiple linear regression was employed for predicting reverberation time based on acoustic features of the workrooms using MATLAB software. The results showed that the measured reverberation times in most of the workrooms were approximately within the ranges recommended by ISO 11690-1. Similarity between reverberation time values calculated by the Sabine formula and measured values was relatively poor (R ²?=?0.39). This can be due to the inaccurate estimation of the acoustic influence of furniture and formula preconditions. Therefore, this value cannot be considered representative of an actual acoustic room. However, the prediction performance of the regression method with root mean square error (RMSE)?=?0.23 s and R ²?=?0.69 is relatively acceptable. Because the sound power of the embroidery machines was relatively high, these sources get the highest priority when it comes to applying noise controls. Finally, an objective approach for the determination of the share of workroom acoustic characteristics in producing noise could facilitate the identification of cost-effective noise controls.     

Preparation and Properties of Starch/Nanosilicate Layer/Polycaprolactone Composites

Starch nanocomposites have been prepared using mineral clay. Montmorillonite, kaolin and a surface-modified montmorillonite by dimethyl (hydrogenated tallow alkyl) ammonium cation were used. Starch-g-PCL nanocomposites have been prepared with graft polymerization through in situ ring-opening polymerization of ε-caprolactone in the presence of starch, Sn(Oct)₂ (Tin(II) 2-ethyl hexanoate) as an initiator/catalyst and silicate layers. In fact, the related composites were prepared in solution method, bulk polymerization and in situ polymerization methods with introducing the mineral clay. The effect of kind of clay on d-spacing of silicate layers was investigated and the obtained nanocomposites were analyzed using X-ray diffraction. The obtained compounds were characterized by Fourier transform infrared (FT-IR). Morphology of the prepared nanocomposites was investigated using scanning electron microscopy and DSC enhanced the study of thermal behaviour of the prepared composite compounds.     

Biodegradation of low-density polyethylene (LDPE) by isolated fungi in solid waste medium

In this study, biodegradation of low-density polyethylene (LDPE) by isolated landfill-source fungi was evaluated in a controlled solid waste medium. The fungi, including Aspergillus fumigatus, Aspergillus terreus and Fusarium solani, were isolated from samples taken from an aerobic aged municipal landfill in Tehran. These fungi could degrade LDPE via the formation of a biofilm in a submerged medium. In the sterilized solid waste medium, LPDE films were buried for 100 days in a 1-L flask containing 400 g sterile solid waste raw materials at 28 °C. Each fungus was added to a separate flask. The moisture content and pH of the media were maintained at the optimal levels for each fungus. Photo-oxidation (25 days under UV-irradiation) was used as a pretreatment of the LDPE samples. The progress of the process was monitored by measurement of total organic carbon (TOC), pH, temperature and moisture. The results obtained from monitoring the process using isolated fungi under sterile conditions indicate that these fungi are able to grow in solid waste medium. The results of FT-IR and SEM analyses show that A. terreus and A. fumigatus, despite the availability of other organic carbon of materials, could utilize LDPE as carbon source. While there has been much research in the field of LDPE biodegradation under solid conditions, this is the first report of degradation of LDPE by A. fumigatus.     

Phosphorus sorption–desorption behaviour of river bed sediments in the Abshineh river, Hamedan, Iran, related to their composition

Phosphorus (P) sorption by sediments may play a vital role in buffering P concentration in the overlying water column. To characterize P sorption–desorption in the river bed sediments, 17 bed sediment samples collected from Abshineh river, in a semi arid region, Hamedan, western Iran were studied through a batch experiment and related to sediment composition. The sorbed fraction ranged from 4.4% to 5.4% and from 38.5% to 86.0% of sorption maxima when 20 and 1,500 mg P kg^?1, respectively, was added to the sediment samples. Phosphorus sorption curves were well fitted to the Langmuir model. Zero equilibrium P concentration ranged from 0.10 to 0.51 mg P l^?1 and varied with sediment characteristics. Phosphorus desorption differed strongly among the studied bed sediments and ranged from 10.8% to 80.2% when 1,500 mg P kg^?1 was added. The results of the geochemical modelling indicated that even under low P addition (2 mg l^?1), the solutions are mainly saturated with respect to hydroxyapatite and ß-tricalcium phosphate minerals and undersaturated with respect to other Ca and Mg minerals, whereas under higher P addition (150 mg l^?1), most Ca–P solid phases, except the most soluble mineral (brushite), will likely precipitate. A Langmuir sorption maximum was positively correlated with carbonate calcium. Estimated P retention capacity of the bed sediments are generally lower and zero equilibrium P concentration values higher in upstream sites than at the downstream sites, suggesting that sediments in upstream and downstream may act as source and sink of P, respectively.