活性焦表面性质对CUO/AC脱硫性能的影响

分别以不同浓度的硝酸处理活性焦载体,采用硝酸铜溶液浸渍法制备CuO/AC催化剂,利用BET、FT-IR和XRD等方法对载体及催化剂进行表征.考察了不同浓度的硝酸处理对活性焦载体性质的影响,并对制得的催化剂的脱硫性能进行了比较.结果表明,活性焦经过硝酸处理后孔结构参数变化很小,而表面含氧酸性官能团的含量有了很大的提高,使...     

MnOx／Al-SBA-15催化剂低温NH3选择性催化还原NO的原位红外研究

用原位红外分别进行了MnOx／Al-SBA-15催化剂上NH3和NO＋O2的吸附态和瞬态实验以及NH3＋NO＋02反应的稳态实验。结果表明，催化剂上存在着L酸位和B酸位，NH3吸附在催化剂上形成配位态的NH3和NH4＋，配位态的NH3能脱氢形成-NH2活性中间态。NO＋O2在催化剂上吸附形成硝酸盐类、硝基类和亚硝酸盐类。将NO＋O2通入预吸附NH3的催化剂中时，表面的配位态的NH3、NH4＋和-NH2都会减少直至消失，SCR反应显著。而将NH3通人预吸附NO＋O2的催化剂中时，只有硝基类和亚硝酸盐类减少，硝酸盐类基本不发生变化，SCR反应微弱。NH3＋NO＋O2稳态反应中，催化剂表面稳定存在着NH4＋和硝酸盐类，SCR反应显著。     

TiO2 nanotube-supported cu as the catalyst for selective NO reduction with NH3

Catalyst supports composed of titanate nanotubes were prepared from hydrothermal treatment on TiO2 nanoparticles in NaOH followed by HCl washing. The nanotubes exhibited well-defined TiO2 anatase phase after calcination at 400 degrees C. The nanotube aggregates and other commercially available TiO2 nanoparticles, all with surface areas >300 m(2)/g, were impregnated with Cu and examined in selective catalytic reduction of NO with NH3. In catalyst preparation, the nanotubes were found to be more thermally stable than nanoparticles, withstanding agglomeration at elevated temperatures. The Cu species supported on the nanotubes showed a higher catalytic activity than those supported on the nanoparticles. Analysis with temperature programmed reduction, X-ray photoelectron spectroscopy, and NO adsorption reflected that the layered-titanate feature of the tube wall was advantageous for even distribution of the Cu species, thus leading to the high-catalytic activity of the tubular Cu/TiO2 catalyst.     

The utilization of catalyst sorbent in scrubbing acid gases from incineration flue gas

Catalyst sorbents based on alumina-supported CuO, CeO2, and CuO-CeO2 were applied to a dry scrubber to clean up the SO2/HCl/NO simultaneously from pilot-scale fluidized-bed incineration flue gas. In the presence of organic compounds, CO and the submicron particles SO2 and HCI removed by the fresh catalyst sorbents and NO reduced to N2 by NH3 under the catalysis of fresh and spent desulfurization/dechloridization (DeSO2/DeHCl) catalyst sorbents (copper compounds, Cu, CuO, and CuSO4) were evaluated in this paper. The fresh and spent catalyst sorbents were characterized by the Brunner-Emmett-Teller method (BET), X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), inductively coupled plasma-mass spectrometry (ICP-MS), and the elemental analyzer (EA). The study showed that the performances of CuO, CeO2, and CuO-CeO2/gamma-Al2O3 were better than that of Ca(OH)2. The removal efficiency of SO2 and HCl was 80-95% in the dry scrubber system. Under NH3/NO = 1, NO could not be reduced to N2 because it was difficult to control the ratio of air/fuel in the flue gas. For estimating the feasibility of regenerating the spent catalyst sorbents, BET and EA analyses were used. They indicated that the pore structures were nearly maintained and a small amount of carbon accumulated on their surface.     

Effect of the Mn oxidation state and lattice oxygen in Mn-based TiO2 catalysts on the low-temperature selective catalytic reduction of NO by NH3

TiO₂-supported manganese oxide catalysts formed using different calcination temperatures were prepared by using the wet-impregnation method and were investigated for their activity in the low-temperature selective catalytic reduction (SCR) of NO by NH₃ with respect to the Mn valence and lattice oxygen behavior. The surface and bulk properties of these catalysts were examined using Brunauer-Emmett-Teller (BET) surface area, X-ray diffraction (XRD), temperature-programmed reduction (TPR), and temperature-programmed desorption (TPD). Catalysts prepared using lower calcination temperatures, which contained Mn⁴⁺, displayed high SCR activity at low temperatures and possessed several acid sites and active oxygen. The TPD analysis determined that the Brönsted and Lewis acid sites in the Mn/TiO₂ catalysts were important for the low-temperature SCR at 80～160 and 200～350 °C, respectively. In addition, the available lattice oxygen was important for attaining high NO to NO₂ oxidation at low temperatures.

Implications: Recently, various Mn catalysts have been evaluated as SCR catalysts. However, there have been no studies on the relationship of adsorption and desorption properties and behavior of lattice oxygen according to the valence state for manganese oxides (MnO_x). Therefore, in this study, the catalysts were prepared by the wet-impregnation method at different calcination temperatures in order to show the difference of manganese oxidation state. These catalysts were then characterized using various physicochemical techniques, including BET, XRD, TPR, and TPD, to understand the structure, oxidation state, redox properties, and adsorption and desorption properties of the Mn/TiO₂ catalysts.     

A predictive mechanism for mercury oxidation on selective catalytic reduction catalysts under coal-derived flue gas

This paper introduces a predictive mechanism for elemental mercury (Hg(o)) oxidation on selective catalytic reduction (SCR) catalysts in coal-fired utility gas cleaning systems, given the ammonia (NH3)/nitric oxide (NO) ratio and concentrations of Hg(o) and HCl at the monolith inlet, the monolith pitch and channel shape, and the SCR temperature and space velocity. A simple premise connects the established mechanism for catalytic NO reduction to the Hg(o) oxidation behavior on SCRs: that hydrochloric acid (HCl) competes for surface sites with NH3 and that Hg(o) contacts these chlorinated sites either from the gas phase or as a weakly adsorbed species. This mechanism explicitly accounts for the inhibition of Hg(o) oxidation by NH3, so that the monolith sustains two chemically distinct regions. In the inlet region, strong NH3 adsorption minimizes the coverage of chlorinated surface sites, so NO reduction inhibits Hg(o) oxidation. But once NH3 has been consumed, the Hg(o) oxidation rate rapidly accelerates, even while the HCl concentration in the gas phase is uniform. Factors that shorten the length of the NO reduction region, such as smaller channel pitches and converting from square to circular channels, and factors that enhance surface chlorination, such as higher inlet HCl concentrations and lower NH3/NO ratios, promote Hg(o) oxidation. This mechanism accurately interprets the reported tendencies for greater extents of Hg(o) oxidation on honeycomb monoliths with smaller channel pitches and hotter temperatures and the tendency for lower extents of Hg(o) oxidation for hotter temperatures on plate monoliths. The mechanism also depicts the inhibition of Hg(o) oxidation by NH3 for NH3/NO ratios from zero to 0.9. Perhaps most important for practical applications, the mechanism reproduces the reported extents of Hg(o) oxidation on a single catalyst for four coals that generated HCl concentrations from 8 to 241 ppm, which covers the entire range encountered in the U.S. utility industry. Similar performance is also demonstrated for full-scale SCRs with diverse coal types and operating conditions.     

Pore structure effects on Ca-based sorbent sulfation capacity at medium temperatures: activated carbon as sorbent/catalyst support

The reaction between three different Ca-based sorbents and SO2 were studied in a medium temperature range (473-773 K). The largest SO2 capture was found with Ca(OH)2 at 773 K, 126.31 mg SO2 x g Ca(OH)2(-1), and the influence of SO2 concentration on the sorbent utilization was observed. Investigations of the internal porous structure of Ca-based sorbents showed that the initial reaction rate was controlled by the surface area, and once the sulfated products were produced, pore structure dominated. To increase the surface area of Ca-based sorbents available to interact with and retain SO2, one kind of CaO/ activated carbon (AC) sorbent/catalyst was prepared to study the effect of AC on the dispersion of Ca-based materials. The results indicated that the Ca-based material dispersed on high-surface-area AC had more capacities for SO2 than unsupported Ca-based sorbents. The initial reaction rates of the reaction between SO2 and Ca-based sorbents and the prepared CaO/AC sorbents/catalysts were measured. Results showed that the reaction rate apparently increased with the presence of AC. It was concluded that CaO/AC was the active material in the desulfurization reaction. AC acting as the support can play a role to supply O2 to increase the affinity to SO2. Moreover, when AC is acting as a support, the surface oxygen functional group formed on the surface of AC can serve as a new site for SO2 adsorption.     

Removal of ammonia solutions used in catalytic wet oxidation processes

Ammonia (NH(3)) is an important product used in the chemical industry, and is common place in industrial wastewater. Industrial wastewater containing ammonia is generally either toxic or has concentrations or temperatures such that direct biological treatment is unfeasible. This investigation used aqueous solutions containing more of ammonia for catalytic liquid-phase oxidation in a trickle-bed reactor (TBR) based on Cu/La/Ce composite catalysts, prepared by co-precipitation of Cu(NO(3))(2), La(NO(3))(2), and Ce(NO(3))(3) at 7:2:1 molar concentrations. The experimental results indicated that the ammonia conversion of the wet oxidation in the presence of the Cu/La/Ce composite catalysts was determined by the Cu/La/Ce catalyst. Minimal ammonia was removed from the solution by the wet oxidation in the absence of any catalyst, while approximately 91% ammonia removal was achieved by wet oxidation over the Cu/La/Ce catalyst at 230 degrees C with oxygen partial pressure of 2.0 MPa. Furthermore, the effluent streams were conducted at a liquid hourly space velocity of under 9 h(-1) in the wet catalytic processes, and a reaction pathway was found linking the oxidizing ammonia to nitric oxide, nitrogen and water. The solution contained by-products, including nitrates and nitrites. Nitrite selectivity was minimized and ammonia removal maximized when the feed ammonia solution had a pH of around 12.0.     

Pore Structure Effects on Ca-Based Sorbent Sulfation Capacity at Medium Temperatures: Activated Carbon as Sorbent/Catalyst Support

Abstract

The reaction between three different Ca-based sorbents and SO₂ were studied in a medium temperature range (473–773 K). The largest SO₂ capture was found with Ca(OH)₂ at 773 K, 126.31 mg SO₂?g Ca(OH)₂ ^?1, and the influence of SO₂ concentration on the sorbent utilization was observed. Investigations of the internal porous structure of Ca-based sorbents showed that the initial reaction rate was controlled by the surface area, and once the sul-fated products were produced, pore structure dominated. To increase the surface area of Ca-based sorbents available to interact with and retain SO₂, one kind of CaO/activated carbon (AC) sorbent/catalyst was prepared to study the effect of AC on the dispersion of Ca-based materials. The results indicated that the Ca-based material dispersed on high-surface-area AC had more capacities for SO₂ than unsupported Ca-based sorbents. The initial reaction rates of the reaction between SO₂ and Ca-based sorbents and the prepared CaO/AC sorbents/cata-lysts were measured. Results showed that the reaction rate apparently increased with the presence of AC. It was concluded that CaO/AC was the active material in the des-ulfurization reaction. AC acting as the support can play a role to supply O₂ to increase the affinity to SO₂. Moreover, when AC is acting as a support, the surface oxygen functional group formed on the surface of AC can serve as a new site for SO₂ adsorption.     

活性炭材料的活化与改性

活性炭是一种应用广泛的吸附催化剂 ,其性能取决于它的孔隙结构和表面化学性质。根据活性炭的表面特性对不同物质的吸附性能 ,对活性炭进行活化和改性处理 ,能进一步满足各种特殊用途的要求。本文概述了活性炭的各种活化和改性处理技术     

Catalytic wet oxidation of ammonia: why is N2 formed preferentially against NO3 -?

The role of catalyst and the reason for the preferential formation of N(2) in the catalytic oxidation reaction of ammonia in water over a Ru (3wt.%)/TiO(2) catalyst were elucidated. It was verified that the catalyst in the reaction had no direct relevance to the selective formation of N(2), but was responsible only for the oxidation of aqueous ammonia, NH(3)(aq), finally giving a molecule of nitrous acid. The preferential production of N(2) was experimentally demonstrated due to the homogeneous aqueous phase reaction of the nitrous acid-dissociated NO(2)(-) with NH(4)(+) ions. Even under the highly oxidizing condition, NO(2)(-) was much more likely to react with NH(4)(+) to form N(2) than being oxidized over the catalyst to NO(3)(-) as long as NH(4)(+) was available in solution.     

CeO2-CoO／ACF低温SCR烟气脱氮性能的研究

活性炭纤维（ACF）经硝酸处理后采用浸渍法制备了CeO2-CoO／ACF复合催化剂，测试了其在以氨气为还原剂的低温SCR过程中的催化活性，同时研究了金属氧化物浸渍顺序及负载量、催化剂煅烧温度、空速比（SV）、NH，／NO（摩尔比）、O2含量等因素对NO转化效率的影响。研究发现，负载量为10％的CeO2-CoO／ACF复合催化剂经煅烧后在120—240℃时具有很高的催化活性，并且在N0初始浓度为1000mg／m3、空速比（SV）为6000h～、NH3／NO为1．05、O：体积分数在3．0％时具有较高的NO转化效率。     

Summer-time distribution of air pollutants in Sequoia National Park, California

Concentrations of air pollutants were monitored during the May November 1999 period on a network of forested sites in Sequoia National Park, California. Measurements were conducted with: (1) active monitors for nitric oxide (NO), nitrogen dioxide (NO2) and ozone (O3); (2) honeycomb denuder/filter pack systems for nitric acid vapor (HNO3), nitrous acid vapor (HNO2), ammonia (NH3), sulfur dioxide (SO2), particulate nitrate (NO3-), ammonium (NH4+), and sulfate (SO4(2-)); and (3) passive samplers for O3, HNO3 and NO2. Elevated concentrations of O3 (seasonal means 41-71 ppb), HNO3 (seasonal means 0.4-2.9 microg/m3), NH3 (seasonal means 1.6-4.5 microg/m3), NO3 (1.1-2.0 microg/m3) and NH4+ (1.0-1.9 microg/m3) were determined. Concentrations of other pollutants were low. With increasing elevation and distance from the pollution source area of O3, NH3 and HNO3 concentrations decreased. Ammonia and NH4+ were dominant N pollutants indicating strong influence of agricultural emissions on forests and other ecosystems of the Sequoia National Park.     

Simultaneous absorption of NO and SO2 into hexamminecobalt(II)/iodide solution

An innovative catalyst system has been developed to simultaneously remove NO and SO2 from combustion flue gas. Such catalyst system may be introduced to the scrubbing solution using ammonia solution to accomplish sequential absorption and catalytic oxidation of both NO and SO2 in the same reactor. When the catalyst system is utilized for removing NO and SO2 from the flue gas, Co(NH3)(6)2+ ions act as the catalyst and I- as the co-catalyst. Dissolved oxygen, in equilibrium with the residual oxygen in the flue gas, is the oxidant. The overall removal process is further enhanced by UV irradiation at 365 nm. More than 95% of NO is removed at a feed concentration of 250-900 ppm, and nearly 100% of SO2 is removed at a feed concentration of 800-2500 ppm. The sulfur dioxide co-existing in the flue gas is beneficial to NO absorption into hexamminecobalt(II)/iodide solution. NO and SO2 can be converted to ammonium sulfate and ammonium nitrate that can be used as fertilizer materials. The process described here demonstrates the feasibility of removing SO2 and NO simultaneously only by retrofitting the existing wet ammonia flue-gas-desulfurization (FGD) scrubbers.     

Enhanced decomposition of NO on the alkalized PdO/Al2O3 catalyst

Experimentally, decomposition of NO on the alkalized Pd/Al2O3 catalyst is remarkably enhanced at 825-1000 K. The enhancement in N2 yield may be due to the additional basic sites on the alkalized catalyst that can trap NO molecules. However, at T > 1000 K, due to the fact that the absorbed oxygen in subsurface or bulk of Pd was involved in the formation and desorption of oxygen molecules, yield of oxygen was enhanced.     

CeO_2-CoO/ACF低温SCR烟气脱氮性能的研究

活性炭纤维(ACF)经硝酸处理后采用浸渍法制备了CeO2-CoO/ACF复合催化剂,测试了其在以氨气为还原剂的低温SCR过程中的催化活性,同时研究了金属氧化物浸渍顺序及负载量、催化剂煅烧温度、空速比(SV)、NH3/NO(摩尔比)、O2含量等因素对NO转化效率的影响。研究发现,负载量为10%的CeO2-CoO/ACF复合催化剂经煅烧后在120~240℃时具有很高的催化活性,并且在NO初始浓度为1 000 mg/m3、空速比(SV)为6 000 h-1、NH3/NO为1.05、O2体积分数在3.0%时具有较高的NO转化效率。     

Selective catalytic oxidation of ammonia over copper-cerium composite catalyst

This work considers the oxidation of ammonia (NH3) by selective catalytic oxidation (SCO) over a copper (Cu)-cerium (Ce) composite catalyst at temperatures between 150 and 400 degrees C. A Cu-Ce composite catalyst was prepared by coprecipitation of copper nitrate and cerium nitrate at various molar concentrations. This study also considers how the concentration of influent NH3 (500-1000 ppm), the space velocity (72,000-110,000 hr(-1)), the relative humidity (12-18%) and the concentration of oxygen (4-20%) affect the operational stability and the capacity for removing NH3. The effects of the O2 and NH3 content of the carrier gas on the catalyst's reaction rate also are considered. The experimental results show that the extent of conversion of NH3 by SCO in the presence of the Cu-Ce composite catalyst was a function of the molar ratio. The NH3 was removed by oxidation in the absence of Cu-Ce composite catalyst, and approximately 99.2% NH3 reduction was achieved during catalytic oxidation over the Cu-Ce (6:4, molar/molar) catalyst at 400 degrees C with an O2 content of 4%. Moreover, the effect of the initial concentration and reaction temperature on the removal of NH3 in the gaseous phase was also monitored at a gas hourly space velocity of less than 92,000 hr(-1).     

A study on the reaction characteristics of vanadium-impregnated natural manganese oxide in ammonia selective catalytic reduction

This study investigated the effect of adding vanadium (V) to natural manganese oxide (NMO) in ammonia (NH3) selective catalytic reduction (SCR). The addition of V to NMO decreased the catalytic activity at low temperatures by blocking the active site. However, the enhancement of catalytic activity was achieved by controlling NH3 oxidation at high temperatures. From the NH3 temperature programmed desorption and oxygen on/off test, it was confirmed that the amount of Lewis acid site and active lattice oxygen of the catalyst affects the catalytic performance at low temperature.     

Catalytic hydrothermal treatment of pulping effluent using a mixture of Cu and Mn metals supported on activated carbon as catalyst

The present study was performed to investigate the performance of activated carbon-supported copper and manganese base catalyst for catalytic wet oxidation (CWO) of pulping effluent. CWO reaction was performed in a high pressure reactor (capacity?=?0.7 l) at temperatures ranging from 120 to 190 °C and oxygen partial pressures of 0.5 to 0.9 MPa with the catalyst concentration of 3 g/l for 3 h duration. With Cu/Mn/AC catalyst at 190 °C temperature and 0.9 MPa oxygen partial pressures, the maximum chemical oxygen demand (COD), total organic carbon (TOC), lignin, and color removals of 73, 71, 86, and 85 %, respectively, were achieved compared to only 52, 51, 53, and 54 % removals during the non-catalytic process. Biodegradability (in terms of 5-day biochemical oxygen demand (BOD₅) to COD ratio) of the pulping effluent was improved to 0.38 from an initial value of 0.16 after the catalytic reaction. The adsorbed carbonaceous fraction on the used catalyst was also determined which contributed meager TOC reduction of 3–4 %. The leaching test showed dissolution of the metals (i.e., Cu and Mn) from the catalysts in the wastewater during CWO reaction at 190 °C temperature and 0.9 MPa oxygen partial pressures. In the future, the investigations should focus on the catalyst reusability.     

Spatial variability of ammonium and nitrate in soils near a poultry farm

This paper assesses the distribution of ammonium (NH4+) and nitrate (NO3-) nitrogen deposition in native bushland soil adjacent to an open ventilated poultry farm. The farm is located in Thirlmere 150 km south west of Sydney, Australia. A total of 104 geographically referenced soil cores were obtained from the study area. Soil pH, electrical conductivity (EC), NH4(+) - and NO3(-)-nitrogen concentrations were analysed for variable trends at three depths, i.e. 0-30, 30-60, and 60-90 cm. Significantly higher concentrations of the two nitrogen forms and EC were observed nearer to the farm in the surface soil samples (0-30 cm). The distribution of NH4+, NO3- and EC were all correlated in surface samples throughout the study area. There was no indication of NH4+ and NO3- leaching within soil profile sampled and it appears that weeds and native vegetation had utilised the accumulated nitrogen. The level of N deposition adjacent to the poultry farm decreased downwind due to dispersion of plume and to the buffering effects from the bushland.