Adsorption of carbon dioxide on amine-modified TiO2 nanotubes

TiO2 nanotubes (TiNT) were prepared by a hydrothermal treatment and modified by three kinds of amines,namely ethylenediamine,polyetherimide and tetraethylenepentamine (TEPA),to study their CO2 adsorption properties from gas streams.The resultant samples were characterized by X-ray diffraction,transmission electron microscopy,and infrared spectroscopy,as well as low temperature N 2 adsorption.CO2 capture was investigated in a dynamic packed column at 30℃.TEPA-modified TiO2 nanotubes showed the highest adsorption capacity of 167.64 mg/g because it had the highest amino-group content among the three amines.CO2 fixation on TiNT impregnated by TEPA was investigated at 30,50,and 70℃,and the adsorption capacity increased slightly with temperature.Following the adsorption step,the sorbents were regenerated by temperature programmed desorption,and the TiNT-TEPA sample,as CO2 sorbent,was found to be readily regenerated and energy-efficient.The cycle test also revealed that the TiNT-TEPA adsorbent is fairly stable,with only a 5% drop in the adsorption capacity after 10 adsorption/desorption cycles.In addition,the CO2 adsorption behavior was investigated with the deactivation model,and which showed an excellent prediction for the TiNT-TEPA breakthrough curves.     

碳底物含量对厌氧条件下水稻土N2、N2O、NO、CO2和CH4排放的影响

理解底物碳氮对厌氧条件下水稻土排放氮素气体——氮气(N2)、氧化亚氮(N2O)和一氧化氮(NO)以及二氧化碳(CO2)和甲烷(CH4)的影响,有助于制定合理的温室气体减排措施,定量了解反硝化产物组成对碳底物水平的依赖性,也有助于氮转化过程模型研发中制定正确的关键过程参数选取方法或参数化方案.本研究采用粉砂壤质水稻土为研究对象,设置对照(CK)和加碳(C+)两个处理,前者的初始硝态氮和可溶性有机碳(DOC)含量分别为~50 mg·kg-1和~28 mg·kg-1,后者的分别为~50 mg·kg-1和~300 mg·kg-1.采用氦环境培养-气体及碳氮底物直接同步测定系统,研究了完全厌氧条件下碳底物水平对上述气体排放的影响.结果表明,CK处理无CH4排放,而C+处理可观测到CH4排放;C+处理的综合增温潜势显著高于CK处理(P<0.01);NO、N2O和N2排放量占这3种氮素气体排放总量的比重,在CK处理分别约为9%、35%和56%,在C+处理分别约为31%、50%和19%,处理间差异显著(P<0.01).由此表明,碳底物水平可显著改变所排放氮素气体的组成;对于旱地阶段硝态氮比较丰富的水稻土,避免在淹水前或淹水期间施用有机肥,有利于削减温室气体排放.     

Probing the potential of polyester for CO2 capture

Global warming, the major environmental issue confronted by humanity today, is caused by rising level of green house gases. Carbon capture and storage technologies offer potential for tapering CO2 emission in the atmosphere. Adsorption is believed to be a promising technology for CO2 capture. For this purpose, a polyester was synthesized by polycondensation of1,3,5-benzenetricarbonyl trichloride and cyanuric acid in pyridine and dichloromethane mixture. The polymer was then characterized using FT-IR, TGA, BET surface area and pore size analysis, FESEM and CO2 adsorption measurements. The CO2 adsorption capacities of the polyester were evaluated at a pressure of 1 bar and two different temperatures（273 and 298 K）.The performance of these materials to adsorb CO2 at atmospheric pressure was measured by optimum CO2 uptake of 0.244 mmol/g at 273 K. The synthesized polyester, therefore, has the potential to be exploited as CO2 adsorbent in pre-combustion capture process.     

厌氧条件下砂壤水稻土N2、N2O、NO、CO2和CH4排放特征

了解厌氧条件土壤反硝化气体(N2、N2O和NO)、CO2和CH4排放特征,是认识反硝化过程机制的基础,并有助于制定合理的温室气体减排措施.定量反硝化产物组成,可为氮转化过程模型研发制定正确的关键过程参数选取方法或参数化方案.本研究选取质地相同(砂壤土)的两个水稻土为研究对象,通过添加KNO3和葡萄糖的混合溶液,将培养土壤的初始NO-3和DOC含量分别调节到50 mg·kg-1和300 mg·kg-1,采用氦环境培养-气体及碳氮底物直接同步测定方法,研究完全厌氧条件下土壤N2、N2O、NO、CO2和CH4的排放特征,并获得反硝化气态产物中各组分的比率.结果表明,在整个培养过程中,两个供试土壤的N2、N2O和NO累积排放量分别为6~8、20和15~18 mg·kg-1,这些气体排放量测定结果可回收土壤NO-3变化量的95%~98%,反硝化气态产物以N2O和NO为主,其中3种组分的比率分别为15%~19%(N2)、47%~49%(N2O)和34%~36%(NO);但反硝化气体产物组成的逐日动态均显现为从以NO为主逐渐过渡到以N2O为主,最后才发展到以N2为主.以上结果说明,反硝化气体产物组成是随反硝化进程而变化的,在以气体产物组成比率作为关键参数计算各种反硝化气体产生率或排放率的模型中,很有必要重视这一点.     

Breakthrough CO2 adsorption in bio-based activated carbons

In this work, the effects of different methods of activation on CO₂ adsorption performance of activated carbon were studied. Activated carbons were prepared from biochar, obtained from fast pyrolysis of white wood, using three different activation methods of steam activation, CO₂ activation and Potassium hydroxide (KOH) activation. CO₂ adsorption behavior of the produced activated carbons was studied in a fixed-bed reactor set-up at atmospheric pressure, temperature range of 25–65°C and inlet CO₂ concentration range of 10–30 mol% in He to determine the effects of the surface area, porosity and surface chemistry on adsorption capacity of the samples. Characterization of the micropore and mesopore texture was carried out using N₂ and CO₂ adsorption at 77 and 273 K, respectively. Central composite design was used to evaluate the combined effects of temperature and concentration of CO₂ on the adsorption behavior of the adsorbents. The KOH activated carbon with a total micropore volume of 0.62 cm³/g and surface area of 1400 m²/g had the highest CO₂ adsorption capacity of 1.8 mol/kg due to its microporous structure and high surface area under the optimized experimental conditions of 30 mol% CO₂ and 25°C. The performance of the adsorbents in multi-cyclic adsorption process was also assessed and the adsorption capacity of KOH and CO₂ activated carbons remained remarkably stable after 50 cycles with low temperature (160°C) regeneration.     

道南膜技术测定Ca(NO3)2溶液体系中汞的化学形态

虽然道南膜技术(DMT)已经成功用于土壤/溶液中多种重金属自由态离子浓度的测定,但DMT技术测定Hg的形态尚未解决.采用DMT测定Ca(NO3)2溶液体系中Hg化学形态.实验结果表明,Hg在阳离子交换膜内的吸附除静电吸附外还存在结合力更强的化学吸附,Hg在阳离子交换膜内扩散成为Hg跨膜传输受阻的主要因素,限制道南膜技术用于Hg形态测定.Hg2+和Hg(OH)2都表现出在阳离子交换膜上的强烈吸附,供端(Donor)Hg损失达50%以上.缩短试验时间至8h以内,可在一定程度上降低Hg吸附.计算结果表明,由于大量的Hg滞留在阳离子交换膜内,在计算受端(Acceptor)Hg浓度时引入滞留系数补偿供端Hg的损失,较好地预测了Ca(NO3)2溶液体系中Hg的化学形态.     

Fabrication of Bi2O3/TiO2 nanocomposites and their applications to the degradation of pollutants in air and water under visible-light

A nanoheterojunction composite photocatalyst Bi2O3/TiO2working under visible-light(λ 420 nm) was prepared by combining two semiconductors Bi2O3 and TiO2 varying the Bi2O3/TiO2molar ratio. Maleic acid was employed as an organic binder to unite Bi2O3 and TiO2 nanoparticles. The SEM, TEM, XRD and diffuse reflectance spectra were utilized to characterize the prepared Bi2O3/TiO2nanoheterojunction. The nanocomposite exhibited unusual high photocatalytic activity in decomposing 2-propanol in gas phase and phenol in aqueous phase and, evolution of CO2 under visible light irradiation while the end members exhibited low photocatalytic activity. The composite was optimized to 5 mol% Bi2O3/TiO2. The remarkable high photocatalytic efficiency originates from the unique relative energy band position of Bi2O3 and TiO2 as well as the absorption of visible light by Bi2O3.     

TiO2/膨润土复合材料对Hg2+的吸附性能研究

利用纳米TiO_2对膨润土进行复合改性,制备TiO_2/膨润土复合材料.采用电镜扫描、X-射线衍射表征改性前后膨润土的结构和形貌.通过室内模拟实验,以膨润土为对照,研究不同添加量、pH、吸附时间及初始Hg~(2+)浓度等条件下,TiO_2/膨润土复合材料对Hg~(2+)的吸附特性与性能,同时通过正交试验,探究TiO_2/膨润土复合材料吸附Hg~(2+)的最优条件.结果表明,改性后的膨润土颗粒明显变小,且颗粒疏松多空孔,层间距增大.相比于膨润土,TiO_2/膨润土复合材料吸附性能得到极大提高.TiO_2/膨润土复合材料对Hg~(2+)的吸附率均随着添加量、pH、吸附时间的增大而增大,添加量为1.5 g·L~(-1)、pH为7.0、吸附时间为120 min时,吸附率达98.0%以上.但TiO_2/膨润土复合材料对Hg~(2+)的吸附率随着初始Hg~(2+)浓度的增大而减小.通过4种动力学模型拟合发现,吸附过程符合假二级动力学方程,吸附以化学吸附为主.吸附等温线更符合Langmuir等温方程,属于典型的单分子层吸附,最大吸附量为20.66 mg·g-1.吸附Hg~(2+)的最优实验条件:添加量为2.0 g·L~(-1),pH为8.0,初始Hg~(2+)浓度为45 mg·L~(-1),吸附时间为16 h,此时吸附率99.9%,平衡浓度为0.034 mg·L~(-1).     

SiO2纳米颗粒内嵌强化介孔TiO2单晶光催化降解盐酸四环素

吸附性能和光生载流子的分离效率是决定光催化降解抗生素的主要因素.为提高介孔TiO_2单晶(MSCs)的吸附性能和光生载流子的分离效率,在MSCs内部构建SiO_2纳米颗粒吸附结构.同时,利用表面光电压谱、氮气等温吸附-脱附、X射线衍射等研究其结构特性.最后,以盐酸四环素为抗生素代表,通过控制SiO_2纳米颗粒比表面积,考察SiO_2对复合材料吸附及光催化性能的影响.结果表明,SiO_2纳米颗粒与TiO_2单晶复合显著提高了材料的吸附性能,表面保护蚀刻进一步提升了材料的比表面积.实验条件下,高比表面积SiO_2-TiO_2单晶复合材料(KSiO_2@TiO_2)对盐酸四环素的平衡吸附量、降解效率、降解速率常数和矿化率分别达到了0.96 mg·g-1、90.2%、0.0079 min-1、54.4%,分别是MSCs的4.4、1.5、2.6和3.1倍.副产物分析表明,SiO_2复合介孔单晶材料更易将盐酸四环素降解为小分子物质.     

膜法氨水吸收脱除烟气中CO2的研究

以氨水为吸收剂,对聚丙烯中空纤维膜分离烟气中CO2进行了实验研究.结果表明:随着气体流量和入口CO2浓度的增加,CO2去除率下降而传质速率增加;随着氨水浓度和氨水流量的增加,CO2去除率和传质速率均显著增加,但当氨水浓度大于2.5 mol·L-1,吸收液流量大于80m L·min-1后,膜接触器对CO2去除率和传质速率基本保持不变;膜接触器连续运行15 d后其吸收性能显著下降,CO2去除率、传质速率、总传质系数均下降约40%~50%.接触角测量、SEM及XPS表征结果表明:随着操作的进行,聚丙烯膜在吸收液环境中接触角逐渐降低,疏水性减弱,造成膜孔润湿;同时碳酸盐在膜孔形成结晶,堵塞膜孔,使得传质阻力进一步增加,从而造成膜接触器吸收性能的下降.     

Optimization of CO2 adsorption capacity and cyclical adsorption/desorption on tetraethylenepentamine-supported surface-modified hydrotalcite

The objective of this research was to investigate CO_2adsorption capacity of tetraethylenepentamine-functionalized basic-modified calcined hydrotalcite(TEPA/b-c HT)sorbents at atmospheric pressure formed under varying TEPA loading levels,temperatures,sorbent weight to total gaseous flow rate(W/F)ratios and CO_2concentrations in the influent gas.The TEPA/b-c HT sorbents were characterized by means of X-ray diffraction(XRD),Fourier transform infrared spectrometry(FT–IR),thermal gravimetric analysis(TGA),Brunauer–Emmet–Teller(BET)analysis of nitrogen(N_2)adsorption/desorption and carbon–hydrogen–nitrogen(CHN)elemental analysis.Moreover,a full 2~4factorial design with three central points at a 95%confidence interval was used to screen important factor(s)on the CO_2adsorption capacity.It revealed that85.0%variation in the capacity came from the influence of four main factors and the15.0%one was from their interactions.A face-centered central composite design response surface method(FCCCD–RSM)was then employed to optimize the condition,the maximal capacity of 5.5–6.1 mmol/g was achieved when operating with a TEPA loading level of 39%–49%(W/W),temperature of 76–90°C,W/F ratio of 1.7–2.60(g·sec)/cm~3and CO_2concentration of 27%–41%(V/V).The model fitted sufficiently the experimental data with an error range of±1.5%.From cyclical adsorption/desorption and selectivity at the optimal condition,the 40%TEPA/b-c HT still expressed its effective performance after eight cycles.     

Influence of SO2 in incineration flue gas on the sequestration of CO2 by municipal solid waste incinerator fly ash

The influence of CO2 content and presence of SO2 on the sequestration of CO2 by municipal solid waste incinerator(MSWI) fly ash was studied by investigating the carbonation reaction of MSWI fly ash with different combinations of simulated flue gas.The reaction between fly ash and 100% CO2 was relatively fast;the uptake of CO2 reached 87g CO2/kg ash,and the sequestered CO2 could be entirely released at high temperatures.When CO2 content was reduced to 12%,the reaction rate decreased;the uptake fell to 41g CO2/kg ash,and 70.7% of the sequestered CO2 could be released.With 12% CO2 in the presence of SO2,the reaction rate significantly decreased;the uptake was just 17g CO2/kg ash,and only 52.9% of the sequestered CO2 could be released.SO2 in the simulated gas restricted the ability of fly ash to sequester CO2 because it blocked the pores of the ash.     

Synthesis, characterization and experimental investigation of Cu-BTC as CO2 adsorbent from flue gas

Porous Cu-BTC material was synthesized by the solvothermal method. Powder X-ray diffraction (PXRD) was used to test the phase purity of the synthesized material and investigate its structural stability under the influence of flue gas components. The thermal stability of the material was determined through thermal gravimetric (TG) analysis. Scanning electron microscopy (SEM) was employed to study the microstructure of the material. Cu-BTC was demonstrated not only to have high CO₂ adsorption capacity but also good selectivity of CO₂ over N₂ by means of packed bed tests. The adsorption capacity of Cu-BTC for CO₂ was about 69 mL/g at 22°C. The influence of the main flue gas components on the CO₂ capacity of the material were discussed as well.     

Ni2P/Bi2MoO6复合材料的制备及可见光催化活性

分别制备了花状Bi₂MoO₆和片状Ni₂P,采用研磨、水热及超声的方式将两种材料复合,考察了负载方式、负载率和溶液pH值对其可见光下降解亚甲基蓝（MB）的影响;利用XRD、XPS、FTIR、SEM、PL和UV-Vis等测试手段表征了样品的微观结构、形貌和光学性质;研究表明Ni₂P作为助催化剂,可加速电子空穴对分离,显著提高Bi₂MoO₆的光催化活性,其中当Ni₂P负载率为4%时,TOC去除率为64.28%,降解速率为纯Bi₂MoO₆的2倍,且将Ni₂P/Bi₂MoO₆复合催化剂循环利用3次后,同实验条件下降解率为94%,证明复合催化剂稳定性好.     

Enhanced CO2 adsorptive performance of PEI/SBA-15 adsorbent using phosphate ester based surfactants as additives

In this study,a series of polyetherimide/SBA-15: 2-D hexagonal P6 mm,Santa Barbara USA(PEI/SBA-15) adsorbents modified by phosphoric ester based surfactants(including tri(2-ethylhexyl)phosphate(TEP),bis(2-ethylhexyl) phosphate(BEP) and trimethyl phosphonoacetate(TMPA))were prepared for CO_2 adsorption.Experimental results indicated that the addition of TEP and BEP had positive effects on CO_2 adsorption capacity over PEI/SBA-15.In particular,the CO_2 adsorption amount could be improved by around 20% for 45PEI–5TEP/SBA-15 compared to the additive-free adsorbent.This could be attributed to the decrease of CO_2 diffusion resistance in the PEI bulk network due to the interactions between TEP and loaded PEI molecules,which was further confirmed by adsorption kinetics results.In addition,it was also found that the cyclic performance of the TEP-modified adsorbent was better than the surfactant-free one.This could be due to two main reasons,based on the results of in situ DRIFT and TG-DSC tests.First and more importantly,adsorbed CO_2 species could be desorbed more rapidly over TEP-modified adsorbent during the thermal desorption process.Furthermore,the enhanced thermal stability after TEP addition ensured lower degradation of amine groups during adsorption/desorption cycles.     

大气14CO2的时空分异特征及其在化石源CO2示踪中的应用

大气CO₂中放射性碳同位素(¹⁴C)的水平可以反映化石源CO₂的影响程度,这对于评估我国目前化石源CO₂的排放状况和制定节能减排政策具有重要的指导意义。本文在概述大气¹⁴CO₂采样和分析方法的基础上,简要介绍了大气¹⁴CO₂观测的起源和主要的源汇过程,重点论述了大气¹⁴CO₂的时空分异特征及其驱动因素;阐述了化石源CO₂浓度的估算方法及¹⁴CO₂在国内外化石源CO₂示踪中的应用现状,并对大气¹⁴CO₂观测在我国化石源CO₂示踪中的应用前景进行了展望;旨在为我国正确地开展大气¹⁴CO₂的观测研究,深刻地理解特定区域大气¹⁴CO₂的时空分异特征和化石源CO₂的分布状况提供参考。     

粉煤灰用于碳捕集、利用及封存的研究进展

总结了国内外粉煤灰用于CO₂捕集、利用和封存的不同技术研究进展,同时对今后的研究和机遇进行了展望.粉煤灰自身可通过直接干式、半干式、湿式和间接方法对CO₂进行矿化捕集封存,在CO₂矿化的同时降低粉煤灰自身重金属的浸出,并且矿化后的粉煤灰因有效降低游离CaO和MgO的含量而更适合于制作混凝土添加剂.粉煤灰也可制成活性炭、沸石和多孔二氧化硅等产品,并对CO₂进行物理吸附捕集,制成产品的类型主要取决于粉煤灰自身的成分组成和理化性质.在CO₂利用方面,粉煤灰除了可拓展建材的利用途径外,还可制作CO₂多种化学工艺所需催化剂或催化剂载体,以及制作新型材料拟薄水铝石等.我国“双碳”目标的提出及燃煤电厂粉煤灰自身的理化特性为粉煤灰提供了一条新的综合利用途径.     

MgO-based adsorbents for CO2 adsorption: Influence of structural and textural properties on the CO2 adsorption performance

A series of MgO-based adsorbents were prepared through solution–combustion synthesis and ball-milling process.The prepared MgO-based powders were characterized using X-ray diffraction,scanning electron microscopy,N_2 physisorption measurements,and employed as potential adsorbents for CO_2 adsorption.The influence of structural and textural properties of these adsorbents over the CO_2 adsorption behaviour was also investigated.The results showed that MgO-based products prepared by solution–combustion and ball-milling processes,were highly porous,fluffy,nanocrystalline structures in nature,which are unique physico-chemical properties that significantly contribute to enhance their CO_2 adsorption.It was found that the MgO synthesized by solution combustion process,using a molar ratio of urea to magnesium nitrate(2:1),and treated by ball-milling during 2.5 hr(MgO-BM2.5h),exhibited the maximum CO_2 adsorption capacity of 1.611 mmol/g at 25℃ and 1 atm,mainly via chemisorption.The CO_2 adsorption behaviour on the MgO-based adsorbents was correlated to their improved specific surface area,total pore volume,pore size distribution and crystallinity.The reusability of synthesized MgO-BM2.5h was confirmed by five consecutive CO_2adsorption–desorption times,without any significant loss of performance,that supports the potential of MgO-based adsorbent.The results confirmed that the special features of MgO prepared by solution–combustion and treated by ball-milling during 2.5 hr are favorable to be used as effective MgO-based adsorbent in post-combustion CO_2 capture technologies.     

新安江水库二氧化碳排放的时空变化特征

新安江水库是我国华东地区最大的水库,面积580 km2,平均深度30 m,水库水体处于中贫营养状态.为了研究新安江水库中CO_2排放的时空变化特征,2014年12月至2015年12月采用静态浮箱法收集水库表面以分子扩散方式排放的CO_2,使用气相色谱仪分析CO_2浓度.结果表明,新安江水库CO_2排放通量从上游入库河流[(120.39±135.41)mg·(m~2·h)~(-1)]至库区主体[(36.65~61.94)mg·(m~2·h)~(-1)]呈下降趋势,而大坝下游河流中CO_2排放通量[(1 535.00±1 447.46)mg·(m~2·h)~(-1)]显著增加,约分别是上游入库河流和库区主体的13倍和25~42倍.但随着与大坝距离增加,大坝下游河流中CO_2排放通量显著下降,如7 km处的CO_2排放通量仅为出库水体处的20%.在库区主体中,CO_2排放通量具有明显的季节变化:CO_2排放通量在秋、冬季时为正值,最大值出现在冬季(12月或1月),说明此时库区表层水体是CO_2排放源;而CO_2排放通量在春、夏季为负值,最小值出现在春季(3、4或5月),说明此时库区表层水体是CO_2吸收汇,这可能与春、夏季时水体中藻类繁殖有关.所以,在调查水库表面CO_2排放时,应对水库的上游入库河流、库区主体和坝下河流进行全面长期的观测,才能避免低估水库中CO_2排放总量.     

Sorbents with high efficiency for CO2 capture based on amines-supported carbon for biogas upgrading

Sorbents for CO_2 capture have been prepared by wet impregnation of a commercial active carbon(Ketjen-black, Akzo Nobel) with two CO_2-philic compounds, polyethylenimine(PEI)and tetraethylenepentamine(TEPA), respectively. The effects of amine amount(from 10 to70 wt.%), CO_2 concentration in the feed, sorption temperature and gas hourly space velocity on the CO_2 capture performance have been investigated. The sorption capacity has been evaluated using the breakthrough method, with a fixed bed reactor equipped with on line gas chromatograph. The samples have been characterized by N_2 adsorption–desorption,scanning electron microscopy and energy dispersive X-ray(SEM/EDX). A promising CO_2 sorption capacity of 6.90 mmol/gsorbenthas been obtained with 70 wt.% of supported TEPA at 70℃ under a stream containing 80 vol% of CO_2. Sorption tests, carried out with simulated biogas compositions(CH_4/CO_2mixtures), have revealed an appreciable CO_2 separation selectivity; stable performance was maintained for 20 adsorption–desorption cycles.