Remarkable promotion effect of trace sulfation on OMS-2 nanorod catalysts for the catalytic combustion of ethanol

OMS-2 nanorod catalysts were synthesized by a hydrothermal redox reaction method using MnSO₄ (OMS-2-SO₄) and Mn(CH₃COO)₂ (OMS-2-AC) as precursors. SO₄^2 −-doped OMS-2-AC catalysts with different SO₄^2 − concentrations were prepared next by adding (NH₄)₂SO₄ solution into OMS-2-AC samples to investigate the effect of the anion SO₄^2 − on the OMS-2-AC catalyst. All catalysts were then tested for the catalytic oxidation of ethanol. The OMS-2-SO₄ catalyst synthesized demonstrated much better activity than OMS-2-AC. The SO₄^2 − doping greatly influenced the activity of the OMS-2-AC catalyst, with a dramatic promotion of activity for suitable concentration of SO₄^2 − (SO₄/catalyst = 0.5% W/W). The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), inductively coupled plasma optical emission spectroscopy (ICP-OES), NH₃-TPD and H₂-TPR techniques. The results showed that the presence of a suitable amount of SO₄^2 − species in the OMS-2-AC catalyst could decrease the Mn–O bond strength and also enhance the lattice oxygen and acid site concentrations, which then effectively promoted the catalytic activity of OMS-2-AC toward ethanol oxidation. Thus it was confirmed that the better catalytic performance of OMS-2-SO₄ compared to OMS-2-AC is due to the presence of some residual SO₄^2 − species in OMS-2-SO₄ samples.     

Role of secondary aerosols in haze formation in summer in the Megacity Beijing

A field experiment from 18 August to 8 September 2006 in Beijing, China, was carried out. A hazy day was defined as visibility < l0 km and RH (relative humidity) < 90%. Four haze episodes, which accounted for ~ 60% of the time during the whole campaign, were characterized by increases of SNA (sulfate, nitrate, and ammonium) and SOA (secondary organic aerosol) concentrations. The average values with standard deviation of SO₄^2 −, NO₃⁻, NH₄⁺ and SOA were 49.8 (± 31.6), 31.4 (± 22.3), 25.8 (± 16.6) and 8.9 (± 4.1) μg/m³, respectively, during the haze episodes, which were 4.3, 3.4, 4.1, and 1.7 times those in the non-haze days. The SO₄^2 −, NO₃⁻, NH₄⁺, and SOA accounted for 15.8%, 8.8%, 7.3%, and 6.0% of the total mass concentration of PM₁₀ during the non-haze days. The respective contributions of SNA species to PM₁₀ rose to about 27.2%, 15.9%, and 13.9% during the haze days, while the contributions of SOA maintained the same level with a slight decrease to about 4.9%. The observed mass concentrations of SNA and SOA increased with the increase of PM₁₀ mass concentration, however, the rate of increase of SNA was much faster than that of the SOA. The SOR (sulfur oxidation ratio) and NOR (nitrogen oxidation ratio) increased from non-haze days to hazy days, and increased with the increase of RH. High concentrations of aerosols and water vapor favored the conversion of SO₂ to SO₄^2 − and NO₂ to NO₃⁻, which accelerated the accumulation of the aerosols and resulted in the formation of haze in Beijing.     

Effect of liming on sulfate transformation and sulfur gas emissions in degraded vegetable soil treated by reductive soil disinfestation

Reductive soil disinfestation (RSD), namely amending organic materials and mulching or flooding to create strong reductive status, has been widely applied to improve degraded soils. However, there is little information available about sulfate (SO₄^2 −) transformation and sulfur (S) gas emissions during RSD treatment to degraded vegetable soils, in which S is generally accumulated. To investigate the effects of liming on SO₄^2 − transformation and S gas emissions, two SO₄^2 −-accumulated vegetable soils (denoted as S1 and S2) were treated by RSD, and RSD plus lime, denoted as RSD₀ and RSD₁, respectively. The results showed that RSD₀ treatment reduced soil SO₄^2 − by 51% and 61% in S1 and S2, respectively. The disappeared SO₄^2 − was mainly transformed into the undissolved form. During RSD treatment, hydrogen sulfide (H₂S), carbonyl sulfide (COS), and dimethyl sulfide (DMS) were detected, but the total S gas emission accounted for < 0.006% of total S in both soils. Compared to RSD₀, lime addition stimulated the conversion of SO₄^2 − into undissolved form, reduced soil SO₄^2 − by 81% in S1 and 84% in S2 and reduced total S gas emissions by 32% in S1 and 57% in S2, respectively. In addition to H₂S, COS and DMS, the emissions of carbon disulfide, methyl mercaptan, and dimethyl disulfide were also detected in RSD₁ treatment. The results indicated that RSD was an effective method to remove SO₄^2 −, liming stimulates the conversion of dissolved SO₄^2 − into undissolved form, probably due to the precipitation with calcium.     

Influences of anion concentration and valence on dispersion and aggregation of titanium dioxide nanoparticles in aqueous solutions

Dispersion and aggregation of nanoparticles in aqueous solutions are important factors for safe application of nanoparticles. In this study, dispersion and aggregation of nano-TiO₂ in aqueous solutions containing various anions were investigated. The influences of anion concentration and valence on the aggregation size, zeta potential and aggregation kinetics were individually investigated. Results showed that the zeta potential decreased from 19.8 to − 41.4 mV when PO₄^3 − concentration was increased from 0 to 50 mg/L, while the corresponding average size of nano-TiO₂ particles decreased from 613.2 to 540.3 nm. Both SO₄^2 − and NO₃⁻ enhanced aggregation of nano-TiO₂ in solution. As SO₄^2 − concentration was increased from 0 to 500 mg/L, the zeta potential decreased from 19.8 to 1.4 mV, and aggregate sizes increased from 613.2 to 961.3 nm. The trend for NO₃⁻ fluctuation was similar to that for SO₄^2 − although the range of variation for NO₃⁻ was relatively narrow. SO₄^2 − and NO₃⁻ accelerated the aggregation rapidly, while PO₄^3 − did so slowly. These findings facilitate the understanding of aggregation and dispersion mechanisms of nano-TiO₂ in aqueous solutions in the presence of anions of interest.     

Kinetics of nitrobenzene degradation coupled to indigenous microorganism dissimilatory iron reduction stimulated by emulsified vegetable oil

Widespread contamination by nitrobenzene(NB) in sediments and groundwater requires better understanding of the biogeochemical removal process of the pollutant. NB degradation, coupled with dissimilatory iron reduction, is one of the most efficient pollutant removal methods. However, research on NB degradation coupled to indigenous microorganism dissimilatory iron reduction stimulated by electron donors is still experimental. A model for remediation in an actual polluted site does not currently exist.Therefore, in this study, the dynamics was derived from the Michaelis–Menten model(when the mass ratio of emulsified vegetable oil and NB reached the critical value 91:1). The effect of SO_4~(2-), NO_3~-, Ca~(2+)/Mg~(2+), and the grain size of aquifer media on the dynamics were studied, and the NB degradation dynamic model was then modified based on the most significant factors. Utilizing the model, the remediation time could be calculated in a contaminated site.     

Potential ammonia emission from flag leaves of paddy rice (Oryza sativa L. cv. Koshihikari)

The present study aimed to investigate the potential ammonia (NH₃) emission from flag leaves of paddy rice (Oryza sativa L. cv. Koshihikari). The study was conducted at a paddy field in central Japan that was designed as a free-air CO₂ enrichment (FACE) facility for paddy rice. A dynamic chamber method was used to measure the potential NH₃ emissions. The air concentrations of NH₃ at two heights (2 and 6 m from the ground surface) were measured using a filter-pack method, and the exchange fluxes of NH₃ of the whole paddy field were calculated using a gradient method. The flag leaves showed potential NH₃ emissions of 25-38 ng N cm⁻² h⁻¹ in the daytime from the heading to the maturity stages, and they showed potentials of approximately 22 ng N cm⁻² h⁻¹, even in the nighttime, at the heading and mid-ripening stages. The exchange fluxes of NH₃ of the whole paddy field in the daytime were net emissions of 0.9-3.9 g N ha⁻¹ h⁻¹ whereas the exchange fluxes of NH₃ in the nighttime were approximately zero.     

Kinetics and mechanism of hexavalent chromium removal by basic oxygen furnace slag

Basic oxygen furnace slag(BOFS) has the potential to remove hexavalent chromium(Cr(VI))from wastewater by a redox process due to the presence of minerals containing Fe2+. The effects of the solution p H, initial Cr(VI) concentration, BOFS dosage, BOFS particle size, and temperature on the removal of Cr(VI) was investigated in detail through batch tests. The chemical and mineral compositions of fresh and reacted BOFS were characterized using scanning electron microscope(SEM) equipped with an energy dispersive spectrometer(EDS)system and X-ray diffractometer(XRD). The results show that Cr(VI) in wastewater can be efficiently removed by Fe2+released from BOFS under appropriate acidic conditions. The removal of Cr(VI) by BOFS significantly depended on the parameters mentioned above. The reaction of Cr(VI) with BOFS followed the pseudo-second-order kinetic model. Fe2+responsible for Cr(VI) removal was primarily derived from the dissolution of Fe O and Fe3O4 in BOFS. When H2SO4 was used to adjust the solution acidity, gypsum(Ca SO4·2H2O)could be formed and become an armoring precipitate layer on the BOFS surface, hindering the release of Fe2+and the removal of Cr(VI). Finally, the main mechanism of Cr(VI) removal by BOFS was described using several consecutive reaction steps.     

Composition and source apportionment of dust fall around a natural lake

The aim of this study was to determine the source apportionment of dust fall around Lake Chini, Malaysia. Samples were collected monthly between December 2012 and March2013 at seven sampling stations located around Lake Chini. The samples were filtered to separate the dissolved and undissolved solids. The ionic compositions(NO-3, SO2-4, Cl-and NH+4) were determined using ion chromatography(IC) while major elements(K, Na, Ca and Mg) and trace metals(Zn, Fe, Al, Ni, Mn, Cr, Pb and Cd) were determined using inductively coupled plasma mass spectrometry(ICP-MS). The results showed that the average concentration of total solids around Lake Chini was 93.49 ± 16.16 mg/(m2·day). SO2-4, Na and Zn dominated the dissolved portion of the dust fall. The enrichment factors(EF) revealed that the source of the trace metals and major elements in the rain water was anthropogenic, except for Fe. Hierarchical agglomerative cluster analysis(HACA) classified the seven monitoring stations and 16 variables into five groups and three groups respectively. A coupled receptor model, principal component analysis multiple linear regression(PCA-MLR), revealed that the sources of dust fall in Lake Chini were dominated by agricultural and biomass burning(42%),followed by the earth's crust(28%), sea spray(16%) and a mixture of soil dust and vehicle emissions(14%).     

Enhanced dechlorination of 2,4-dichlorophenol by recoverable Ni/Fe–Fe3O4 nanocomposites

Ni/Fe-Fe_3O_4 nanocomposites were synthesized for dechlorination of 2,4-dichlorophenol(2,4-DCP). The effects of the Ni content in Ni/Fe-Fe_3O_4 nanocomposites, solution pH, and common dissolved ions on the dechlorination efficiency were investigated, in addition to the reusability of the nanocomposites. The results showed that increasing content of Ni in Ni/Fe–Fe_3O_4 nanocomposites, from 1 to 5 wt.%, greatly increased the dechlorination efficiency; the Ni/Fe–Fe_3O_4 nanocomposites had much higher dechlorination efficiency than bare Ni/Fe nanoparticles. Ni content of 5 wt.% and initial p H below 6.0 was found to be the optimal conditions for the catalytic dechlorination of 2,4-DCP. Both 2,4-DCP and the intermediate product 2-chlorophenol(2-CP) were completely removed, and the concentration of the final product phenol was close to the theoretical phenol production from complete dechlorination of 20 mg/L of 2,4-DCP, after 3 hr reaction at initial p H value of 6.0,3 g/L Ni/Fe-Fe_3O_4 , 5 wt.% Ni content in the composite, and temperature of 22℃. 2,4-DCP dechlorination was enhanced by Cl-and inhibited by NO3-and SO_4~(2-). The nanocomposites were easily separated from the solution by an applied magnetic field. When the catalyst was reused, the removal efficiency of 2,4-DCP was almost 100% for the first seven uses, and gradually decreased to 75% in cycles 8–10. Therefore, the Ni/Fe–Fe_3O_4 nanocomposites can be considered as a potentially effective tool for remediation of pollution by 2,4-DCP.     

Rapid degradation of dyes in water by magnetic Fe/Fe3O4/graphene composites

Magnetic Fe⁰/Fe₃O₄/graphene has been successfully synthesized by a one-step reduction method and investigated in rapid degradation of dyes in this work. The material was characterized by N₂ sorption–desorption, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), vibrating-sample magnetometer (VSM) measurements and X-ray photoelectron spectroscopy (XPS). The results indicated that Fe⁰/Fe₃O₄/graphene had a layered structure with Fe crystals highly dispersed in the interlayers of graphene, which could enhance the mass transfer process between Fe⁰/Fe₃O₄/graphene and pollutants. Fe⁰/Fe₃O₄/graphene exhibited ferromagnetism and could be easily separated and re-dispersed for reuse in water. Typical dyes, such as Methyl Orange, Methylene Blue and Crystal Violet, could be decolorized by Fe⁰/Fe₃O₄/graphene rapidly. After 20 min, the decolorization efficiencies of methyl orange, methylene blue and crystal violet were 94.78%, 91.60% and 89.07%, respectively. The reaction mechanism of Fe⁰/Fe₃O₄/graphene with dyes mainly included adsorption and enhanced reduction by the composite. Thus, Fe⁰/Fe₃O₄/graphene prepared by the one-step reduction method has excellent performance in removal of dyes in water.     

Urease inhibitor reduces N losses and improves plant-bioavailability of urea applied in fine particle and granular forms under field conditions

A field lysimeter/mini plot experiment was established in a silt loam soil near Lincoln, New Zealand, to investigate the effectiveness of urea fertilizer in fine particle application (FPA), with or without the urease inhibitor N-(n-butyl) thiophosphoric triamide (NBPT - “Agrotain”), in decreasing nitrogen (N) losses and improving N uptake efficiency. The five treatments were: control (no N) and ¹⁵N-labelled urea, with or without NBPT, applied to lysimeters or mini plots (unlabelled urea), either in granular form to the soil surface or in FPA form (through a spray) at a rate equivalent to 100 kg N ha⁻¹. Gaseous emissions of ammonia (NH₃) and nitrous oxide (N₂O), nitrate (NO₃⁻) leaching, herbage dry-matter (DM) production, N-response efficiency, total N uptake and total recovery of applied ¹⁵N in the plant and soil varied with urea application method and with addition of NBPT. Urea with NBPT, applied in granular or FPA form, was more effective than in application without NBPT: N₂O emissions were reduced by 7-12%, NH₃ emissions by 65-69% and NO₃⁻ leaching losses by 36-55% compared with granular urea. Urea alone and with NBPT, applied in FPA form increased herbage DM production by 27% and 38%, respectively. The N response efficiency increased from 10 kg DM kg⁻¹ of applied N with granular urea to 19 kg DM kg⁻¹ with FPA urea and to 23 kg DM kg⁻¹ with FPA urea plus NBPT. Urea applied in FPA form resulted in significantly (P < 0.05) higher ¹⁵N recovery in the shoots compared with granular treatments and this was improved further when urea in FPA form was applied with NBPT. These results suggest that applying urea with NBPT in FPA form has potential as a management tool in mitigating N losses, improving N-response efficiency and increasing herbage DM production in intensive grassland systems.     

Phosphate recovery from anaerobic digester effluents using CaMg(OH)4

Dolomite lime(DL)(CaMg(OH)_4) was used as an economical source of Mg~(2+)for the removal and recovery of phosphate from an anaerobic digester effluent of a municipal wastewater treatment plant(MWWTP) wastewater. Batch precipitation results determined that phosphate was effectively reduced from 87 to less than 4 mg-P/L when the effluent water was mixed with 0.3 g/L of DL. The competitive precipitation mechanisms of different solids in the treatment system consisting of Ca~(2+)–Mg~(2+)–NH_4~+–PO_4~(3-)CO_3~(2-)were determined by comparing model predictions with experimental results. Thermodynamic model calculations indicated that hydroxyapatite(Ca_(10)(PO_4)_6(OH)_2), Ca_4H(PO_4)_3?3H_2O, Ca_3(PO_4)_2(beta), and Ca_3(PO_4)_2(am2)were more stable than struvite(MgNH_4PO_3?6H_2O) and calcite(CaCO_3). However, X-ray diffraction(XRD) analysis determined the formation of struvite and calcite minerals in the treated effluent. Kinetic experimental results showed that most of the phosphate was removed from synthetic effluent containing NH_4~+within 2 hr, while only 20% of the PO_4~(3-)was removed in the absence of NH_4~+after 24 hr of treatment. The formation of struvite in the DL-treated effluent was due to the rapid precipitation rate of the mineral. The final pH of the DL-treated effluent significantly influenced the mass ratio of struvite to calcite in the precipitates. Because more calcite was formed when the p H increased from 8.4 to 9.6, a p H range of 8.0–8.5 should be used to produce solid with high PO_4~(3-)content. This study demonstrated that DL could be used for effective removal of phosphate from the effluent and that resultant precipitates contained high content of phosphate and ammonium.     

Fe2O3添加对钛基SCR催化剂表面硫酸氢铵分解行为的影响规律

采用共沉淀法合成了TiO_2及TiO_2-Fe_2O_3载体,并对硫酸氢铵与上述载体之间的相互作用及硫酸氢铵的具体分解行为进行了研究.结果表明,催化剂载体表面含硫官能团主要以双齿硫酸盐的形式存在,含氮官能团以铵根离子的形式存在.当硫酸氢铵沉积于催化剂载体表面时,由于硫酸根离子具有较强的电负性,Ti原子及Fe原子处于电子缺失状态.对于TiO_2载体,硫酸根离子主要与Ti原子相连;而对于TiO_2-Fe_2O_3载体,Ti原子及Fe原子均为硫酸根离子主要的附着位点.采用热分析方法及原位红外对硫酸氢铵在TiO_2及TiO_2-Fe_2O_3载体表面的分解行为进行了研究,发现铁氧化物的添加显著促进了硫酸氢铵在低温区间内的分解行为;与铵根离子相比,硫酸根离子具有更高的热稳定性.催化剂稳定性测试结果表明,铁氧化物的添加显著提高了低温抗硫抗水性能,为实现低温SCR技术的工业应用提供了理论基础.     

Chemical characterization of size-resolved aerosols in four seasons and hazy days in the megacity Beijing of China

Size-resolved aerosol samples were collected by MOUDI in four seasons in 2007 in Beijing. The PM₁₀ and PM_1.8 mass concentrations were 166.0 ± 120.5 and 91.6 ± 69.7 μg/m³, respectively, throughout the measurement, with seasonal variation: nearly two times higher in autumn than in summer and spring. Serious fine particle pollution occurred in winter with the PM_1.8/PM₁₀ ratio of 0.63, which was higher than other seasons. The size distribution of PM showed obvious seasonal and diurnal variation, with a smaller fine mode peak in spring and in the daytime. OM (organic matter = 1.6 × OC (organic carbon)) and SIA (secondary inorganic aerosol) were major components of fine particles, while OM, SIA and Ca^2 + were major components in coarse particles. Moreover, secondary components, mainly SOA (secondary organic aerosol) and SIA, accounted for 46%–96% of each size bin in fine particles, which meant that secondary pollution existed all year. Sulfates and nitrates, primarily in the form of (NH₄)₂SO₄, NH₄NO₃, CaSO₄, Na₂SO₄ and K₂SO₄, calculated by the model ISORROPIA II, were major components of the solid phase in fine particles. The PM concentration and size distribution were similar in the four seasons on non-haze days, while large differences occurred on haze days, which indicated seasonal variation of PM concentration and size distribution were dominated by haze days. The SIA concentrations and fractions of nearly all size bins were higher on haze days than on non-haze days, which was attributed to heterogeneous aqueous reactions on haze days in the four seasons.     

Kinetics and corrosion products of aqueous nitrate reduction by iron powder without reaction conditions control

Although considerable research has been conducted on nitrate reduction by zero-valent iron powder (Fe0), these studies were mostly operated under anaerobic conditions with invariable pH that was unsuitable for practical application. Without reaction conditions (dissolved oxygen or reaction pH) control, this work aimed at subjecting the kinetics of denitrification by microscale Fe0 (160–200 mesh) to analysis the factors affecting the denitrification of nitrate and the composition of iron reductive products c...     

Online single particle measurement of fireworks pollution during Chinese New Year in Nanning

Time-resolved single-particle measurements were conducted during Chinese New Year in Nanning, China. Firework displays resulted in a burst of SO_2, coarse mode, and accumulation mode(100–500 nm) particles. Through single particle mass spectrometry analysis, five different types of particles(fireworks-metal, ash, dust, organic carbon-sulfate(OC-sulfate), biomass burning) with different size distributions were identified as primary emissions from firework displays. The fireworks-related particles accounted for more than70% of the total analyzed particles during severe firework detonations. The formation of secondary particulate sulfate and nitrate during firework events was investigated on single particle level. An increase of sulfite peak(80SO_3~-) followed by an increase of sulfate peaks(97HSO_4~-+ 96SO_4~-) in the mass spectra during firework displays indicated the aqueous uptake and oxidation of SO_2 on particles. High concentration of gaseous SO_2, high relative humidity and high particle loading likely promoted SO_2 oxidation. Secondary nitrate formed through gas-phase oxidation of NO_2 to nitric acid, followed by the condensation into particles as ammonium nitrate. This study shows that under worm, humid conditions, both primary and secondary aerosols contribute to the particulate air pollution during firework displays.     

Synthesis,crystal structure,photodegradation kinetics and photocatalytic activity of novel photocatalyst ZnBiYO4

ZnBiYO₄ was synthesized by a solid-state reaction method for the first time. The structural and photocatalytic properties of ZnBiYO₄ were characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV–Vis diffuse reflectance. ZnBiYO₄ crystallized with a tetragonal spinel structure with space group I41/A. The lattice parameters for ZnBiYO₄ were a = b = 11.176479 Å and c = 10.014323 Å. The band gap of ZnBiYO₄ was estimated to be 1.58 eV. The photocatalytic activity of ZnBiYO₄ was assessed by photodegradation of methyl orange under visible light irradiation. The results showed that ZnBiYO₄ had higher catalytic activity compared with N-doped TiO₂ under the same experimental conditions using visible light irradiation. The photocatalytic degradation of methyl orange with ZnBiYO₄ or N-doped TiO₂ as catalyst followed first-order reaction kinetics, and the first-order rate constant was 0.01575 and 0.00416 min^− 1 for ZnBiYO₄ and N-doped TiO₂, respectively. After visible light irradiation for 220 min with ZnBiYO₄ as catalyst, complete removal and mineralization of methyl orange were observed. The reduction of total organic carbon, formation of inorganic products, SO₄^2 − and NO₃⁻, and evolution of CO₂ revealed the continuous mineralization of methyl orange during the photocatalytic process. The intermediate products were identified using liquid chromatography–mass spectrometry. The ZnBiYO₄/(visible light) photocatalysis system was found to be suitable for textile industry wastewater treatment and could be used to solve other environmental chemical pollution problems.     

Removal of Cs from water and soil by ammonium-pillared montmorillonite/Fe3O4 composite

To remove cesium ions from water and soil, a novel adsorbent was synthesized by following a one-step co-precipitation method and using non-toxic raw materials. By combining ammonium-pillared montmorillonite (MMT) and magnetic nanoparticles (Fe₃O₄), an MMT/Fe₃O₄ composite was prepared and characterized. The adsorbent exhibited high selectivity of Cs⁺ and could be rapidly separated from the mixed solution under an external magnetic field. Above all, the adsorbent had high removal efficiency in cesium-contaminated samples (water and soil) and also showed good recycling performance, indicating that the MMT/Fe₃O₄ composite could be widely applied to the remediation of cesium-contaminated environments. It was observed that the pH, solid/liquid ratio and initial concentration affected adsorption capacity. In the presence of coexisting ions, the adsorption capacity decreased in the order of Ca^2 + > Mg^2 + > K⁺ > Na⁺, which is consistent with our theoretical prediction. The adsorption behavior of this new adsorbent could be expressed by the pseudo-second-order model and Freundlich isotherm. In addition, the adsorption mechanism of Cs⁺ was NH₄⁺ ion exchange and surface hydroxyl group coordination, with the former being more predominant.     

Particulate matter assessment of a wetland in Beijing

To increase the knowledge on the particulate matter of a wetland in Beijing, an experimental study on the concentration and composition of PM₁₀ and PM_2.5 was implemented in Beijing Olympic Forest Park from 2013 to 2014. This study analyzed the meteorological factors and deposition fluxes at different heights and in different periods in the wetlands. The results showed that the mean mass concentrations of PM₁₀ and PM_2.5 were the highest at 06:00–09:00 and the lowest at 15:00–18:00. And the annual concentration of PM₁₀ and PM_2.5 in the wetland followed the order of dry period (winter) > normal water period (spring and autumn) > wet period (summer), with the concentration in the dry period significantly higher than that in the normal water and wet periods. The chemical composition of PM_2.5 in the wetlands included NH₄⁺, K⁺, Na⁺, Mg^2 +, SO₄^2 −, NO₃⁻, and Cl⁻, which respectively accounted for 12.7%, 1.0%, 0.8%, 0.7%, 46.6%, 33.2%, and 5.1% of the average annual composition. The concentration of PM₁₀ and PM_2.5 in the wetlands had a significant positive correlation with relative humidity, a negative correlation with wind speed, and an insignificant negative correlation with temperature and radiation. The daily average dry deposition amount of PM₁₀ in the different periods followed the order of dry period > normal water period > wet period, and the daily average dry deposition amount of PM_2.5 in the different periods was dry period > wet period > normal water period.     

Enhanced photoelectrocatalytic degradation of ammonia by in situ photoelectrogenerated active chlorine on TiO2 nanotube electrodes

TiO_2 nanotube(Ti NT) electrodes anodized in fluorinated organic solutions were successfully prepared on Ti sheets. Field-emission scanning electron microscopy(FE-SEM) and X-ray diffraction(XRD) were performed to characterize the TiNT electrodes. The linear voltammetry results under irradiation showed that the TiNT electrode annealed at 450°C presented the highest photoelectrochemical activity. By combining photocatalytic with electrochemical process, a significantly synergetic effect on ammonia degradation was observed with Na_2SO_4 as supporting electrolyte at pH 10.7. Furthermore, the photoelectrocatalytic efficiency on the ammonia degradation was greatly enhanced in presence of chloride ions without the limitation of pH. The degradation rate was improved by 14.8 times reaching 4.98 × 10~(-2) min~(-1) at pH 10.7 and a faster degradation rate of 6.34 × 10~(-2) min~(-1)was obtained at pH 3.01. The in situ photoelectrocatalytic generated active chlorine was proposed to be responsible for the improved efficiency. On the other hand, an enhanced degradation of ammonia using TiNT electrode fabricated in fluorinated organic solution was also confirmed compared to TiNT electrode anodized in fluorinated water solution and TiO_2 film electrode fabricated by sol–gel method. Finally, the effect of chloride concentration was also discussed.