北京市饮用水中溴酸盐、卤代乙酸及高氯酸盐研究

调查了北京市饮用水厂源水及出厂水中消毒副产物溴酸盐、卤代乙酸及典型污染物高氯酸盐的污染现状,研究了其来源及环境影响因素.结果表明,北京市饮用水中基本不含溴酸盐;含有5种卤代乙酸和高氯酸盐.饮用水加氯消毒是产生卤代乙酸的主要原因.在所调查水厂出厂水中卤代乙酸的平均浓度为42.1～149.5μg/L;其中含氯卤代乙酸占总量的90%以上.5种卤代乙酸的含量顺序为三氯乙酸>二氯乙酸>氯溴乙酸>二溴乙酸>一溴二氯乙酸.饮用水中卤代乙酸受季节影响较大,9月份浓度最高,4月份浓度最低.高氯酸盐主要存在于以地下水为源水的水厂中,受地下水污染影响较大.各水厂出厂水中高氯酸盐含量为0.1～6.8μg/L.饮用水中高氯酸盐在11月份含量最高,7月份含量最低.     

含氮消毒副产物卤乙酰胺的水解特性

为探究高毒性含氮消毒副产物HAcAms（卤乙酰胺）的水解特性,选取水中普遍存在的2种溴代HAcAms[BCAcAm（溴氯乙酰胺）、DBAcAm（二溴乙酰胺）]与2种氯代HAcAms[DCAcAm（二氯乙酰胺）、TCAcAm（三氯乙酰胺）]作为研究对象,研究pH、初始ρ（HAcAms）、温度、氯消毒剂和氯胺消毒剂等因素对HAcAms稳定性的影响.结果表明:①4种HAcAms在pH为5和7时较稳定,在pH为8~10下发生碱性催化水解反应,并且水解速率随pH升高而增加.②相同碱性环境中,4种HAcAms的水解速率大小依次为TCAcAm > DCAcAm > BCAcAm > DBAcAm,并且初始ρ（HAcAms）（30~150 μg/L）越小,温度（25~35℃）越高,HAcAms水解速率越大.③中性条件下,4种HAcAms在ρ（NaClO）（NaClO为次氯酸钠）为1~5 mg/L时均迅速氯化分解,并且分解速率随ρ（NaClO）增加而增大,4种HAcAms分解速率的大小规律与其碱性水解速率大小规律一致.④当pH为7时,4种HAcAms在ρ（NH₂Cl）（NH₂Cl为一氯胺）为0.5~5 mg/L下较稳定.研究显示,水中HAcAms在高pH、低初始ρ（HAcAms）、高温及氯消毒剂存在的条件下易水解,其中溴代HAcAms比氯代HAcAms更稳定,其在饮用水与再生水中的风险更需要重视.      

海水淡化低温多效蒸馏工艺(LT-MED)沿程溴代消毒副产物的生成

研究了海水淡化低温多效蒸馏(LT-MED)工艺沿程水质和溴代消毒副产物(Br-DBPs)变化特征.LT-MED工艺进水海水的Br-浓度和比紫外吸收值(SUVA)分别为54.6 mg·L~(-1)和1.7 L·(mg·m)-1,其荧光特征有机物主要有色氨酸类芳香族蛋白质、富里酸类有机物和溶解性微生物代谢产物.进水海水经Na Cl O消毒后,DBPs的种类和浓度显著增加,且增加的主要为Br-DBPs,三溴甲烷(CHBr3)占总三卤甲烷(THMs)的100%;一溴乙酸(C2H3Br O2)和二溴乙酸(C2H2Br2O2)分别占总卤乙酸(HAAs)的31.9%和68.1%;四溴苯酚(C6H5Br O)占总卤代酚(HPs)的100%.LT-MED海水淡化产品水中THMs、HAAs和HPs均未检出,但是其浓水中的THMs、HAAs和HPs浓度分别为56.9、35.0和0.1μg·L~(-1).     

饮用水中卤乙酸致癌性的研究进展

目前饮用水中主要氯化消毒副产物卤乙酸由于难挥发和难降解,其危害研究特别是致癌性越来越引起人们的重视,为此笔者对饮用水中卤乙酸(主要包括二氯乙酸、三氯乙酸、二溴乙酸)的暴露水平、代谢、致癌性、致癌机制、流行病学研究等方面的研究工作进行了综述,并指出了今后研究的方向.     

海水淡化超滤-反渗透工艺沿程溴代消毒副产物变化规律

研究了海水淡化超滤-反渗透(UF-RO)工艺沿程有机物和溴代消毒副产物(Br-DBPs)变化特征.该海水中含有较高浓度的Br-(45.6~50.9 mg·L-1)和较多的芳香类化合物[比紫外吸收值SUVA为3.6~6.0 L·(mg·m)-1];色氨酸类芳香族蛋白质、富里酸类有机物和溶解性微生物代谢产物是海水中主要的荧光特征有机物.UF-RO工艺进水海水经Na Cl O消毒后,DBPs的种类和浓度显著增加,且增加的主要为Br-DBPs,其中三溴甲烷(CHBr3)占总三卤甲烷(THMs)的70.48%~91.50%,二溴乙酸(Br2CHCO2H)占总卤乙酸(HAAs)的81.14%~100%,二溴乙腈(C2HBr2N)占总卤乙腈(HANs)的83.77%~87.45%.UF膜对THMs、HAAs和HANs的去除率分别为36.63%~40.39%、73.83%~95.38%和100%.RO膜可以完全去除HAAs,但是对THMs不能完全去除.进水海水的抗雌激素活性为0.35~0.44 mg·L-1,氯消毒后增加了32%~69%.海水淡化UF-RO系统生成的DBPs和其他生物毒性物质最终被截留到了UF浓水和RO浓水中.     

新型溴代苯酚类消毒副产物的氯化降解机制

最近,13种新型极性卤代苯酚类消毒副产物在氯化消毒后的饮用水中被发现,它们按结构被分成4组,分别是二卤-4-羟基苯甲醛、二卤-4-羟基苯甲酸、二卤水杨酸和三卤苯酚.为研究它们在氯化消毒过程中的降解机制,选取了其中的4种全溴代种类,即3,5-二溴-4-羟基苯甲醛、3,5-二溴-4-羟基苯甲酸、3,5-二溴水杨酸以及2,4,6-三溴苯酚,利用UPLC/ESI-tq MS中的前体离子扫描,多反应监测和子离子扫描,鉴定了这几种消毒副产物在氯化消毒过程中的中间产物以及终产物,并根据这些中间产物和终产物与消毒时间的关系推测了其降解路径.结果表明,除了3,5-二溴水杨酸相对较稳定外,其余3种消毒副产物在氯化消毒过程中不稳定,通过取代、水解以及氧化等过程最终降解为卤乙酸等脂肪族小分子消毒副产物.在降解过程中有许多中间产物被检测并鉴定出来,其中包含一组具有五元环结构的新型消毒副产物(三卤代-羟基环戊烯二酮).     

水中利谷隆氯化降解动力学和消毒副产物生成特性

采用常用消毒剂次氯酸钠对含氮除草剂利谷隆开展了氯化降解实验研究,系统考察了加氯量、p H值、加Br-量以及温度对降解效果的影响,分析了氯化反应过程中消毒副产物生成特性.结果表明,次氯酸钠对利谷隆的氧化降解过程符合二级反应动力学;p H值对该降解反应影响较大,当p H值为7时反应速率最快,其中HOCl、OCl-与利谷隆的基元反应速率常数分别为4.84×102L·(mol·h)-1和3.80×102L·(mol·h)-1.在添加溴离子时,反应速率随着溴离子的加入逐渐减小.改变温度时,反应速率随着温度的增加而逐渐增大.利谷隆在氯化降解过程中可产生三氯甲烷、二氯乙腈、三氯硝基甲烷、卤代丙酮等多类型消毒副产物.在不同p H值和添加溴离子条件下,消毒副产物种类与浓度会出现显著差异.     

水中溴离子对氯化消毒副产物的影响

根据我国某城市饮用水中三卤甲烷类物质的现状，对水中Ｂｒ＾－的存在，Ｂｒ＾－对ＴＨＭｓ，卤代乙酸类物质形成的影响以及ＴＨＭｓ，ＨＡＡｓ形成的机理等进行综述，且提出了控制饮用水氯化消毒副产物的相应对策。     

钴活化过一硫酸盐氧化过程中卤代副产物的生成

活化过硫酸盐产生的硫酸根自由基(SO~(·-)_4)可以降解大多数有机污染物,被广泛用于地下水、土壤修复等领域.本研究发现在钴活化过一硫酸盐(PMS)高级氧化过程中,溴离子会被SO~(·-)_4氧化生成自由溴,继而和苯酚反应生成溴代苯酚,最终生成三溴甲烷和二溴乙酸等副产物.当反应液中苯酚初始浓度为0.05 mmol·L~(-1)、Br~-浓度0.2 mmol·L~(-1)、Co~(2+)浓度5μmol·L~(-1)、PMS浓度1 mmol·L~(-1)、p H为6.0时,三溴甲烷和二溴乙酸的生成随反应的进行先增加后降低,在8 h达到最大,分别为10.3μmol·L~(-1)和14.6μmol·L~(-1).卤代副产物的生成随p H的升高而降低.当卤离子总量保持不变,随着溶液中Cl~-/Br~-比例的增加,卤代副产物的生成总量逐渐降低,而含氯副产物的产量逐渐增加.本研究为全面评价过硫酸盐高级氧化工艺在污染控制方面的应用可行性提供了依据.     

饮用水中卤代消毒副产物的产生和影响因素的研究

论述了卤代消毒副产物（三卤甲烷和卤代乙酸）对人体健康的危害，研究了投氯量、氯化时间、ｐＨ值和温度对它们的影响，提出了去除卤代消毒副产物的途径。     

Effect of ferric and bromide ions on the formation and speciation of disinfection byproducts during chlorination

The e ects of ferric ion, pH, and bromide on the formation and distribution of disinfection byproducts (DBPs) during chlorination were studied. Two raw water samples from Huangpu River and Yangtze River, two typical drinking water sources of Shanghai, were used for the investigation. Compared with the samples from Huangpu River, the raw water samples from Yangtze River had lower content of total organic carbon (TOC) and ferric ions, but higher bromide concentrations. Under controlled chlorination conditions, four trihalomethanes (THMs), nine haloacetic acids (HAAs), total organic halogen (TOX) and its halogen species fractions, including total organic chlorine (TOCl) and total organic bromide (TOBr), were determined. The results showed that co-existent ferric and bromide ions significantly promoted the formation of total THMs and HAAs for both raw water samples. Higher concentration of bromide ions significantly changed the speciation of the formed THMs and HAAs. There was an obvious shift to brominated species, which might result in a more adverse influence on the safety of drinking water. The results also indicated that high levels of bromide ions in raw water samples produced higher percentages of unknown TOBr.     

南水北调丹江口水库水氯(胺)化消毒副产物产生特性与消毒工艺对比

系统研究了南水北调中线工程水源——丹江口水库水在氯(胺)化消毒条件下,常规消毒副产物的产生特性,考察了消毒方式、消毒剂投加量、接触时间、p H和溴离子浓度等因素的影响,并对消毒工艺参数进行了优化.结果发现,丹江口水库水经氯化消毒可产生三氯甲烷、二氯一溴甲烷等常规含碳和较低浓度二氯乙腈、三氯硝基甲烷等含氮消毒副产物,而氯胺化消毒仅产生三氯甲烷和三氯硝基甲烷等消毒副产物(disinfection by-products,DBPs).自由氯消毒过程产生的各类型DBPs浓度约为氯胺消毒的7.5倍,短时自由氯转氯胺方式DBPs产生量介于两者之间;随着自由氯投加量增加,各类型消毒副产物均呈现增加趋势,投加量大于2 mg·L-1后DBPs增加量较少.随氯胺投加量增加,三氯甲烷生成量变化不大,投加量大于2mg·L-1后可产生三氯硝基甲烷等副产物.随反应时间延长,自由氯的衰减速率明显大于氯胺,同时消毒副产物增长量明显快于氯胺消毒.随着p H升高,自由氯消毒后三卤甲烷含量呈现增加趋势,而氯胺消毒后变化不明显.随溴离子浓度的增加,自由氯和氯胺消毒后副产物类型均向溴代DBPs转变,同时总生成量明显增加,自由氯消毒DBPs增长量明显大于氯胺消毒过程.丹江口水库水采用氯胺化消毒可以降低消毒副产物的生成风险,如采用自由氯消毒方式,水厂需根据实际常规处理工艺重点控制自由氯的投加量等参数.     

Formation and control of disinfection byproducts and toxicity during reclaimed water chlorination: A review

Chlorination is essential to the safety of reclaimed water; however, this process leads to concern regarding the formation of disinfection byproducts (DBPs) and toxicity. This study reviewed the formation and control strategies for DBPs and toxicity in reclaimed water during chlorination. Both regulated and emerging DBPs have been frequently detected in reclaimed water during chlorination at a higher level than those in drinking water, indicating they pose a greater risk to humans. Luminescent bacteria and Daphnia magna acute toxicity, anti-estrogenic activity and cytotoxicity generally increased after chlorination because of the formation of DBPs. Genotoxicity by umu-test and estrogenic activity were decreased after chlorination because of destruction of toxic chemicals. During chlorination, water quality significantly impacted changes in toxicity. Ammonium tended to attenuate toxicity changes by reacting with chlorine to form chloramine, while bromide tended to aggravate toxicity changes by forming hypobromous acid. During pretreatment by ozonation and coagulation, disinfection byproduct formation potential (DBPFP) and toxicity formation potential (TFP) occasionally increase, which is accompanied by DOC removal; thus, the decrease of DOC was limited to indicate the decrease of DBPFP and TFP. It is more important to eliminate the key fraction of precursors such as hydrophobic acid and hydrophilic neutrals. During chlorination, toxicities can increase with the increasing chlorine dose and contact time. To control the excessive toxicity formation, a relatively low chlorine dose and short contact time were required. Quenching chlorine residual with reductive reagents also effectively abated the formation of toxic compounds.     

The role of metal oxides on oxidant decay and disinfection byproduct formation in drinking waters: Relevance to distribution systems

Maintaining a residual disinfectant/oxidant (e.g., chlorine and chlorine dioxide), is a generally used strategy to control microbial contaminants and bacterial regrowth in distribution systems. Secondarily oxidant, such as hypobromous acid (HOBr), can be formed during chlorination of bromide-containing waters. The decay of oxidants and formation of disinfection byproducts (DBPs) due to the interaction between oxidants and selected metal oxides were studied. Selected metal oxides generally enhanced the decay of these halogen-containing oxidants via three pathways: (1) catalytic disproportionation to yield an oxidized form of halogen (i.e., halate) and reduced form (halide for chlorine and bromine or chlorite for chlorine dioxide), (2) oxygen formation, and (3) oxidation of a metal in a reduced form (e.g., cuprous oxide) to a higher oxidation state. Cupric oxide (CuO) and nickel oxide (NiO) showed significantly strong abilities for the first pathway, and oxygen formation was a side reaction. Cuprous oxide can react with oxidants via the third pathway, while goethite was not involved in these reactions. The ability of CuO on catalytic disproportionation of HOBr remained stable up to four cycles. In chlorination process, bromate formation tends to be important (exceeding 10 µg/L) when initial bromide concentration is above 400 µg/L in the presence of dissolved organic matter. Increasing initial bromide concentrations increased the formation of DBPs and calculated cytotoxicity, and the maximum was observed at pH 8.6 during chlorination process. Therefore, the possible disinfectant loss and DBP formation should be carefully considered in drinking water distribution systems.     

Formation pathways of brominated products from benzophenone-4 chlorination in the presence of bromide ions

The brominated products, formed in chlorination treatment of benzophenone-4 in the presence of bromide ions, were identified, and the formation pathways were proposed.Under disinfection conditions, benzophenone-4 would undertake electrophilic substitution generating mono- or di-halogenated products, which would be oxidized to esters and further hydrolyzed to phenol derivatives. The generated catechol intermediate would be transformed into furan-like heterocyclic product. The product species were p H-dependent,while benzophenone-4 elimination was chlorine dose-dependent. When the chlorination treatment was performed on ambient water spiked with benzophenone-4 and bromide ions, most of brominated byproducts could be detected, and the acute toxicity significantly increased as well.     

模拟泳池水中氯化消毒副产物的生成规律

以模拟泳池水为研究对象,研究不同的氯化时间、氯投加量、pH值、反应温度条件对泳池水在氯化消毒过程中生成消毒副产物（DBPs）的影响.研究结果表明：延长氯化反应时间,二氯乙酸（DCAA）、三氯乙酸（TCAA）和三氯甲烷（TCM）的浓度不断升高,二氯乙腈（DCAN）、三氯硝基甲烷（TCNM）和1,1,1-三氯丙酮（1,1,1-TCP）的浓度则先升高再降低.DBPs浓度在氯化反应的前24h增幅较大,48h后趋于平缓;随着氯投加量的增加,DCAA、TCAA、TCM、TCNM和1,1,1-TCP浓度一直呈上升趋势,而DCAN浓度则先升高再降低.在氯投加量为2mg/L时,DBPs的浓度较低;在pH值从6升高到8的过程中,DCAA、TCAA、DCAN和1,1,1-TCP浓度先升高再降低,TCM和TCNM浓度则一直升高.pH值在6~7范围内可有效控制DBPs的形成;随着反应温度的升高,DCAA、TCAA、TCM和TCNM浓度持续升高,DCAN和1,1,1-TCP则逐渐降低.综上所述,应合理调节泳池水的氯化消毒条件,在保证舒适度的同时有效控制DBPs的生成.     

氯、氯胺消毒下钱江源水源水消毒副产物形成特征研究

以钱江源水源水为研究对象,以氯、氯胺为消毒方式,研究了不同消毒条件下,三卤甲烷(THMs)、卤乙腈(HANs)、氯代酮(CKs)、二卤乙酸(DHAAs)、三卤乙酸(THAAs)等消毒副产物(DBPs)的形成情况,以便为水务工作者监测钱江源建库前后水质、DBPs形成的变化提供基础数据.结果显示,氯消毒下DBPs的产量比氯胺消毒高出3~7倍甚至1个数量级,但不管是氯消毒还是氯胺消毒,THMs、HAAs形成量均在我国饮用水标准范围内.氯消毒下,大部分DBPs产量为中、碱性条件酸性条件(除了CKs),氯胺消毒则呈现不同的情况(所有DBPs的产量均为p H=6、p H=7p H=8).消毒剂量对所有DBPs形成具有明显的促进作用;溴离子对THMs、DHANs、DHAAs的形成有明显的促进作用.进一步研究表明,钱江源水源水的水质比钱塘江下游九溪水源水好,DBPs形成也较低,某些指标(如有机碳、有机氮、HANs形成量等)甚至比同省水质较好的金兰水库还要好;而且由于其较高的比紫外吸收值(SUVA),DBPs的溴嵌入能力均比九溪水源水、金兰水库低.此外,就目前的钱江源水源水来说,控制消毒剂量(氯、或氯胺)是控制DBPs形成的有效策略.     

UV/氯联合处理含溴溶液中溴酸根的生成

研究了UV和氯联合作用下溴酸根离子(BrO^-₃)在低浓度含溴溶液中的生成,旨在探讨pH、次氯酸钠(NaOCl)浓度、溶解氧(DO)、光强和温度等因素对其生成的影响.研究表明,暗反应条件下H₂O-NaOCl-Br^-体系较稳定,而UV照射可使游离氯浓度持续降低,同时伴有部分Br^-（6 .6%～32%）被氧化成BrO^-₃离子;pH、温度和光强恒定时余氯的分解可用拟一级反应速率方程拟合;实验条件下（I为610～1 896 μW/cm²,T为12 .2～36 .1℃）,拟一级反应速率常数分别与体系温度和光强值有线性关系;BrO^-₃的生成大致可以分为快速、慢速和平缓3个阶段;在慢速生成阶段,BrO^-₃的生成量与余氯的分解量有良好的线性关系（绝大部分相关系数在0 .96以上）;实验范围内（pH为4 .41～11 .07,DO为1 .5～9 　mg/L,Cl₂为1 .23～4 .50 　mg/L）,低pH、低DO和高初始NaOCl（以氯计）浓度有利于溴酸根的生成,提高温度与光强均不同程度提高溴酸根生成速度,但同时因加速余氯的分解而减少了溴酸根的总生成时间.     

饮用水中典型微生物消毒过程中消毒副产物的生成规律

以饮用水中典型微生物--大肠杆菌（Escherichia coli）为试验对象,研究pH值、氯化时间、氯投量及细菌浓度对大肠杆菌在氯化消毒过程中生成消毒副产物（DBPs）的影响,并分析何种氯化条件下,DBPs控制效果最佳.研究表明：随氯投量增加,二氯乙腈（DCAN）呈先上升后下降趋势;随氯化时间延长,三氯丙酮（1,1,1-TCP）和DCAN先增加后减少;在pH值从5升高到9时,1,1,1-DCP、三氯硝基甲烷（TCNM）、二氯乙酸（DCAA）和三氯乙酸（TCAA）持续降低;细菌污染水源事件在近年常有报道,当水源水中细菌浓度增加时,饮用水中三氯甲烷（TCM）、TCNM、DCAA和TCAA浓度增加,但DCAN、三氯乙腈（TCAN）、二氯丙酮（1,1-DCP）和1,1,1-TCP不一定增加.为了达到低毒性的目的,氯投量浓度不宜太高,同时控制氯化时间为6h和pH>8.     

Degradation of duloxetine: Identification of transformation products by UHPLC-ESI(+)-HRMS/MS, in silico toxicity and wastewater analysis

Duloxetine (DUL), an antidepressant drug, has been detected in surface water and wastewater effluents, however, there is little information on the formation of its transformation products (TPs). In this work, hydrolysis, photodegradation (UV irradiation) and chlorination experiments were performed on spiked distillated water, under controlled experimental conditions to simulate abiotic processes that can occur in the environment and wastewater treatment plants (WWTPs). Eleven TPs, nine from reaction with UV light and two from chlorine contact, were formed and detected by ultra-high performance liquid chromatography coupled to quadrupole time-of-flight mass spectrometry, and nine of them had their chemical structures elucidated upon analyses of their fragmentation patterns in MS/MS spectra. The formation and degradation of the TPs were observed. The parent compound was completely degraded after 30?min in photodegradation and after 24?hr in chlorination. Almost all TPs were completely degraded in the experiments. The ecotoxicity and mutagenicity of the TPs were predicted based on several in silico models and it was found that a few of these products presented more ecotoxicity than DUL itself and six TPs showed positive mutagenicity. Finally, wastewater samples were analyzed and DUL and one TP, possibly formed by chlorination process, were detected in the effluent, which showed that WWTP not only did not remove DUL, but also formed a TP.