A spectrophotometric assay method for vanadium in biological and environmental samples using 2,4-dinitrophenylhydrazine with imipramine hydrochloride

A simple, rapid, and sensitive method involving the interaction of 2,4-dinitrophenylhydrazine with imipramine hydrochloride in presence of vanadium (V) in sulfuric acid medium has been proposed for the determination of vanadium. The purple-colored product developed showed an absorption maximum at 560 nm and was stable for 24 h. The working curve was linear over the concentration range of 0.1–2.8 μg ml^− 1, with sensitivity of detection of 0.0124 μg ml^− 1. Molar absorptivity and Sandell’s sensitivity were found to be 2.6 × 10⁴ l/mol cm and 0.0039 μg cm^− 1, respectively. The accuracy of the proposed method was assessed by Student’s t test and variance ratio F test, and the results were on par with the reported method. The method was successfully used in the determination of V in water, human urine, soil, and plant samples, and it was free from interference by various concomitant ions.     

Biofilms coating Schoenoplectus californicus as indicators of water quality in the Río de la Plata Estuary (Argentina)

N-ethyl-3-carbazolecarboxaldehyde-3-thio- semicarbazone (ECCT) as an new analytical reagent used for the development of a highly sensitive extractive spectrophotometric method for the determination of copper(II). The ECCT forms a greenish-yellow colored 1:1 (M:L) complex with copper(II) at pH 3.0, which is well extracted into n-butanol and shows maximum absorbance at 380nm. The color of the complex is stable for more than forty eight hours. The system obey Beer's law in the range 0.4–3.6 with 2.243 × 10⁴lmol⁻¹cm⁻¹, 2.83 × 10^-3μgcm⁻² molar absorptivity and Sandell's sensitivity respectively. The regression coefficient is 0.412 with 0.99 correlation coefficient. The precision and accuracy of the method was checked by finding the relative standard deviation (0.422%). This developed method has been successfully employed for the determination of copper(II) in environmental and pharmaceutical samples. The method is evaluated by analyzing samples from the bureau of analyzed samples (BCS 233, 266, 216/1, 207 and 179) and by inter comparison of experimental values using AAS.     

Facile and Sensitive Spectrophotometric Determination of Carbosulfan in Formulations and Environmental Samples

Facile, selective and sensitive spectrophotometric method has been developed for the determination of carbosulfan in insecticidal formulations, fortified water, food grains, agriculture wastewater and soil samples with newly synthesized reagents. The method was based on acid and alkaline hydrolysis of the carbosulfan pesticide, and the resultant hydrolysis product of carbosulfan was coupled with 2,6-dibromo-4-methylaniline to give a yellow color product with λ _max of 464 nm or interaction with 2,6-dibromo-4-nitroaniline to produce yellow colored product with λ _max of 408 nm or coupling with 2,4,6-tribromoaniline to form red colored product has a λ _max of 471 nm. Under optimal conditions, Beer’s law range for 2,6-dibromo-4-methylaniline (DBMA) was found to be 0.2–12.0 μg ml⁻¹, 0.6–16.0 μg ml⁻¹ for 2,6-dibromo-4-nitroaniline (DBNA) and 0.4–15.0 μg ml⁻¹ for 2,4,6-tribromoaniline (TBA). The molar absorptivity of the color systems were found to be 3.112 × 10⁴ l mol⁻¹ cm⁻¹ for DBMA, 3.214 × 10⁴ l mol⁻¹ cm⁻¹ for DBNA and 3.881 × 10⁴ l mol⁻¹ cm⁻¹ for TBA. Sandell’s of the color reactions are 0.013 μg cm⁻² (DBMA), 0.012 μg cm⁻² (DBNA) and 0.011 μg cm⁻² (TBA) respectively. The effect of the non-target species on the determination of carbosulfan was studied to enhance the selectivity of the proposed methods. The formation of colored derivatives with the coupling agents is instantaneous and stable for 28, 30, and 26 h. Performance of the proposed methods were compared statistically in terms Student’s F and t-tests with the reported methods. An erratum to this article can be found at     

Determination of ametryn in sugarcane and ametryn–atrazine herbicide formulations using spectrophotometric method

A sensitive spectrophotometric method has been developed for determination of ametryn in agricultural samples. The proposed method was based on reaction with pyridine and further coupling with sulfanilic acid to form a colored product. The absorbance was measured at 400 nm with a molar absorptivity of 2.1 × 10⁵ L mol⁻¹ cm⁻¹. The method shows a linear range from 0.2–20 μg mL⁻¹ with limit of detection and limit of quantification 0.16 and 0.54 μg mL⁻¹, respectively. The method has been successfully applied to the determination of ametryn in sugarcane juice and commercial formulations after separation of ametryn from triazine herbicides based on solvent extraction. Recovery values were found to be in the range of 96.0 ± 0.2% to 98.4 ± 0.1%.     

Development of simple and sensitive spectrophotometric method for the determination of bendiocarb in its formulations and environmental samples

Facile, selective and sensitive spectrophotometric method has been developed for the determination of bendiocarb in its insecticidal formulations, fortified water, food grains, agriculture wastewater and agriculture soil samples with prepared reagents. The method was based on alkaline hydrolysis of the bendiocarb pesticide, and the resultant hydrolysis product of bendiocarb was coupled with 2,6-dibromo-4-methylaniline to give a yellow color product with λmaxof457 nmorcouplingwith2, 6−dibromo−4−nitroanilinetoproducearedcoloredproductwithλ_max of474~nmorcouplingwith2, 4, 6−tribromoanilinetoformorangeredcoloredproducthasaλ_max of465 nm.Underoptimalconditions, Beer'slawrangefor2, 6−dibromo−4−methylaniline(DBMA)wasfoundtobe0.6−−14.0~μgmL ^-1, 0.8−−10.0 μgmL ^-1 for2, 6−dibromo−4−nitroaniline(DBNA)and0.4−−10.0 μgmL ^-1 for2, 4, 6−tribromoaniline(TBA).Themolarabsorptivityofthecolorsystemswerefoundtobe4.126~×~10⁴ lmol ^-1 cm ^-1 forDBMA, 3.254×10⁴ l~mol ^-1 cm ^-1 forDBNAand2.812×10⁴ lmol ^-1 cm ^-1 forTBA.Sandell'softhecolorreactionsare0.018 μgcm ^-2(DBMA), 0.052 μgcm ^-2(DBNA)and0.065 μgcm ^-2$ (TBA) respectively. The effect of the non-target species on the determination of bendiocarb was studied. The formation of colored derivatives with the coupling agents is instantaneous and stable for 18 h, 30 h, and 12 h. Performance of the proposed methods were compared statistically in terms Student's F and t-tests with the reported methods.     

Estimation Of Selenium Concentration In Shallow Groundwater In Alluvial Fan Area In Tsukui, Central Japan

Total selenium (Se) and water-soluble Se in soil, and Se in a shallow groundwater were hydrogeochemically researched in an alluvial fan area in Tsukui, Central Japan. The water-soluble Se was estimated at average level of 2.6 ± 1.2μg Se kg⁻¹ dry soil (± SD, n = 25), showing less than 1% of the total Se (349–508μg Se kg⁻¹ dry soil) in soil. The monthly Se concentration in groundwater was average 2.2μg,L⁻¹, ranging 1.6–2.4μg,L⁻¹ during 2001–2003. The Se in groundwater significantly decreased with increasing groundwater level after rainfall. This result indicated that Se-bearing water percolated with relatively low Se concentration through the soil layer. According to our prediction model of linear regression curve on the observation data, Se concentration in the groundwater was estimated to be increasing with the very low rate of 4.35 × 10⁻³μg Se L⁻¹,yr⁻¹. The hydrogeochemical research and the result of the prediction model showed that any explosive increase of Se will hardly occur in this groundwater without an anthropogenic Se contamination.     

Risk assessment due to intake of heavy metals through the ingestion of groundwater around two proposed uranium mining areas in Jharkhand,India

Heavy metal pollution of water resources can be apprehended in East Singhbhum region which is a highly mineralised zone with extensive mining of copper, uranium and other minerals. Ten groundwater samples were collected from each site and the heavy metal analysis was done by atomic absorption spectrophotometer. Analysis of the results of the study reveals that the concentration of iron, manganese, zinc, lead, copper and nickel in groundwater of Bagjata mining area ranged 0.06–5.3 mg l^− 1, 0.01–1.3 mg l^− 1, 0.02–8.2 mg l^− 1, 1.4–28.4 μg l^− 1, 0.78–20.0 μg l^− 1 and 1.05–20.1 μg l^− 1, respectively. In case of Banduhurang mining area, the range was 0.04–2.93 mg l^− 1, 0.02–1.1 mg l^− 1, 0.01–4.68 mg l^− 1, 1.04–33.21 μg l^− 1, 1.24–18.7 μg l^− 1 and 1.06–14.58 μg l^− 1, respectively. The heavy metals were found to be below the drinking water standards (IS:10500 1993) except iron (0.3 mg l^− 1) and manganese (0.1 mg l^− 1). The hazard quotients of the heavy metals for drinking water were below 1 posing no threat due to intake of water to the people for both the areas.     

Pesticide residues in rain water from Hisar, India

Presence of pesticide residues was studied in rain water during 2002 employing multi residue analysis method by gas liquid chromatography equipped with ECD and NPD detectors and capillary columns. The presence of pesticide residues in surface aquatic system triggered the investigation of the presence of pesticides in rain water. A total of 13 pesticides were detected in rain water samples. Among the different groups of pesticides, organochlorines were present in the range of 0.041–7.060 ppb with maximum concentration of p,p’-DDT up to 7.060 μg l⁻¹. Synthetic pyrethroids were present ranging from 0.100 to 1.000 μg l⁻¹ and organophosphates in the range of 0.050–4.000 μg l⁻¹ showing maximum contamination with cypermethrin (1.000 μg l⁻¹) and monocrotophos (4.000 μg l⁻¹) of the respective groups. Almost 80% samples showed the residues above MRL of 0.5 ppb fixed for multi residues and on the basis of single pesticide, 16–50% samples contained residues above the MRL value of 0.1 ppb.     

Removal of hexavalent chromium from contaminated ground water using zero-valent iron nanoparticles

Batch experiments were conducted on ground water samples collected from a site contaminated with Cr(VI) to evaluate the redox potential of zero-valent iron (Fe⁰) nanoparticles for remediation of Cr(VI)-contaminated ground water. For this, various samples of contaminated ground water were allowed to react with various loadings of Fe⁰ nanoparticles for a reaction period of 60 min. Data showed 100% reduction of Cr(VI) in all the contaminated ground water samples after treatment with 0.20 gL⁻¹ of Fe⁰ nanoparticles. An increase in the reduction of Cr(VI) from 45% to 100% was noticed with the increase in the loading of Fe⁰ nanoparticles from 0.05 to 0.20 gL⁻¹. Reaction kinetics of Cr(VI) reduction showed pseudo first-order kinetics with rate constant in the range of 1.1 × 10⁻³ to 3.9 × 10⁻³ min⁻¹. This work demonstrates the potential utility of Fe⁰ nanoparticles in treatment and remediation of Cr(VI)-contaminated water source.     

Monitoring of (bio)available labile metal fraction in a drinking water treatment plant by diffusive gradients in thin films

A performance study of diffusive gradients in thin films (DGT) and inductively coupled plasma optical emission spectrometry (ICP-OES) was applied for the monitoring of the labile fraction of metals Al, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn, in Sant Joan Despí Drinking Water Treatment Plant located in the South of Barcelona’s Metropolitan Area (Spain). The DWTP monitoring protocol was optimized by working for 1 day of deployment (24 h) with the DGT device in contact with both treated and river water matrixes. Additionally, it was demonstrated that an increase in the deployment time of 1 week did not decrease the evaluated concentrations of the studied metals. The quality parameters of the DGT device and ICP-OES determination, such as limit of quantification, accuracy expressed as relative error (%) and reproducibility expressed as relative standard deviation, were evaluated. Good results were obtained for all the metals in ultrapure water; limits of quantification ranged from 1.5 μg L^− 1 for cadmium to 28 μg L^− 1 for zinc when deployment time of 24 h was used and from 0.2 μg L^− 1 for cadmium to 4 μg L^− 1 for zinc when this time was increased by 1 week. Accuracy and precisions lower than or equal to 10% were obtained at a parametric concentration value of the metals regulated in the European Drinking Water Guidelines (98/83/EC). DGT deployment was tested in river and treated water, and good results were obtained for Cd, Ni, Co and Zn, whereas for the other metals, a continuous control of their metallic labile fractions was monitored. Therefore, DGT device allows the continuous monitoring of the labile metal species in a drinking water treatment plant.     

Status of insecticide contamination of soil and water in Haryana, India

Twelve samples each of soil and ground water were collected from paddy-wheat, paddy-cotton, sugarcane fields and tube wells from same or near by fields around Hisar, Haryana, India during 2002–2003 to monitor pesticide residues. Residues were estimated by GC-ECD and GC-NPD systems equipped with capillary columns for organochlorine, synthetic pyrethroid and organophosphate insecticides. In soil, HCH (0.002–0.051 μg g⁻¹), DDT (0.001–0.066 μg g⁻¹), endosulfan (0.002–0.039 μg g⁻¹) and chlordane (0.0002–0.019 μg g⁻¹) among organochlorines, cypermethrin (0.001–0.035 μg g⁻¹) and fenvalerate (0.001–0.022 μg g⁻¹) among synthetic pyrethroids and chlorpyriphos (0.002–0.172 μg g⁻¹), malathion (0.002–0.008 μg g⁻¹), quinalphos (0.001–0.010 μg g⁻¹) among organophosphates were detected. Dominant contaminants were DDT, cypermethrin and chlorpyriphos from the respective groups. In water samples, HCH, DDT, endosulfan and cypermethrin residues were observed frequently. Only chlorpyriphos among organophosphates was detected in 10 samples. On consideration of tube well water for drinking purpose, about 80% samples were found to contain residues above the regulatory limits.     

Water quality assessment: surface water sources used for drinking and irrigation in Zaria,Nigeria are a public health hazard

We assessed the quality and pollution status of source surface waters in Zaria, Nigeria by monitoring the nature, cause and extent of pollution in Samaru stream, Kubanni River and Kubanni dam over a period of 10 months, between March and December 2002. A total of 228 water samples was collected from 12 sites and analysed for a total of ten physicochemical and one bacteriological quality indicators, using standard methods. Aesthetic water quality impairment parameters were also observed. The mean values of most water quality parameters were significantly higher (P < 0.05) in both the stream and river than in the dam. There was no significant correlation between faecal coliform counts (FCC) and water temperature (in the range 15–33°C); pH (5.77–7.32); and turbidity (1.4–567 NTU). The high FCC ranged from 2.0 × 10¹ to 1.6 × 10⁶ MPN/100 ml and exceeded the WHO standards for drinking water and water used for fresh-produce irrigation, and correlated positively (P < 0.05) with conductivity (in the range 68–1,029 μS/cm); TDS (10.0–70.0 mg/l); TSS (10.0–70.0 mg/l); Cl (7.5–181 mg/l); PO₄⁻P (0.01–0.41 mg/l); NO₃⁻N (0.6–3.8 mg/l) and BOD₅ (0.1–14.9 mg/l). The main pollution sources were municipal wastewater, stormwater runoffs, the ABU sewage treatment plant, abattoir effluents and irrigation farms treated with chemical fertilisers. We conclude that these water bodies are potentially hazardous to public health and that proper sewage treatment and river quality monitoring are needed to warn against hazards to public health.     

RETRACTED ARTICLE: Biomonitoring fallout <Superscript>137</Superscript>Cs in resident and migratory fishes collected along the southern coast of India and assessment of dose

The globally distributed fallout radionuclide ¹³⁷Cs was monitored in 25 resident and 22 migratory fish species collected from some regions of west and east coast of southern India to establish a baseline data. The samples were collected during June 2008 to June 2009. Higher level of ¹³⁷Cs was noted in planktivorous fishes and lower level in herbivores. A significant variation in ¹³⁷Cs was observed between fishes with different feeding habits and different migratory pattern. Oceanodromic migratory fishes displayed higher cesium levels than other migratory types. Similarly, migratory fishes displayed higher ¹³⁷Cs concentration compared to resident fishes. The overall range of ¹³⁷Cs varied from 0.06 to 0.3 Bq/kg in fishes. The biological concentration varied from 55 to 250. The average external dose rate to fishes was calculated to be 2.7 × 10⁻⁷ μGy/h, while the internal dose rate varied from 8.50 × 10⁻⁶ to 5.27 × 10⁻⁵ μGy/h. The hazard quotient for fishes was found to be less than 1. The average intake of ¹³⁷Cs via fishes to the public was calculated to be 3.5 Bq/year and subsequently the committed effective dose was 0.05 μSv/year. The data obtained were less than global average and comparable to those of many regions.     

Testing differences in methods of preparing moss samples

The main objective of this research was to estimate the total mass of nitrogen discharged from various sources in Korea using the mass balance approach. Three different nitrogen mass balances were presented: (1) agricultural activities including raising crops and animal husbandry; (2) domestic activities, and (3) activities in forest and urban areas. These nitrogen balances were combined to estimate riverine discharge of nitrogen to the ocean in national scale. Nitrogen inputs include atmospheric deposition, biological nitrogen fixation, application of inorganic fertilizers/manures, animal feed/imported foodstuffs, and meat/fish. Nitrogen outputs include ammonia volatilization, denitrification, human/animal waste generation, crop/meat production, and riverine discharge to the ocean. The estimated total nitrogen input in Korea was 1,194.5 × 10³ tons N/year. Nitrogen discharged into rivers was estimated as 408–422 × 10³ tons N/year, of which 66–71% was diffuse in origin. The estimated diffuse discharges for land uses were estimated as 82 × 10³ tons N/year from agricultural areas, 7 × 10³ tons N/year from forestry and 75 × 10³ tons N/year from urban and industrial areas.     

Assessment of water quality of Manchar Lake in Sindh (Pakistan)

Manchar Lake is the largest natural freshwater lake in Pakistan. The Lake has received less fresh water in past few years. In addition, drainage water is being discharged in the Lake through Main Nara Valley Drain (MNVD) since many years. Consequently, concern has grown regarding the water quality of the Lake. The aim of this study was to assess the water quality of Manchar Lake and MNVD and the objectives were to determine physiochemical properties and the concentrations of common cations and anions as well as seven trace metals i.e. Cu, Ni, Zn, Co, Fe, Pb and Cd. The concentration of the trace metals were determined by simultaneous preconcentration and solvent extraction using flame atomic absorption spectrometer. Results of physicochemical parameters of Manchar Lake water samples showed mean pH 8.4 (±0.2), conductivity 2,310.3 (±581.3) μS cm⁻¹ and hardness (as CaCO₃) 213.1 (±62.3) mg l⁻¹. Mean concentrations of cations and anions were Na 521.5 (±49.7), Cl⁻ 413.6 (±225.7), Ca 70.7 (±12.9), Mg 56.2 (±28.9), K 17.6 (±6.5), 0.34 (±0.2) and 0.02 (±0.01) mg l⁻¹. Mean concentrations of trace metals were Zn 15.7 (±1), Fe 12 (±3.5), Pb 9 (±2.7), Cu 8.9 (±7.7), Ni 4.3 (±3.4), Co 4 (±3.4) and Cd 1.1 (±1) μg l⁻¹. MNVD water samples showed mean pH 8.9 (±0.8), conductivity 1,735.7 (±567.8) μS cm⁻¹ and hardness (as CaCO₃) 184.8 (±32.4) mg l⁻¹. In MNWD, the mean concentrations of cations and anions were Na 482.7 (±11.7), Cl⁻ 395.7 (±271.5), Ca 79.1 (±23.5), Mg 54.2 (±28.1), K 26.2 (±21.3), NO⁻³ 0.5 (±0.3) and 0.1 (±0.1) mg l⁻¹. Mean concentrations of trace metals observed in MNWD water were Fe 14.9(±3.5), Cd 8.3 (±9.4), Pb 6.9 (±2.4), Cu 6.6 (±3.1), Zn 6.2 (±1.8), Co 4.5 (±2.7), and Ni 3.5 (±2.9) μg l⁻¹. The pH of both Manchar Lake and MNVD waters and concentration of Pb in Manchar Lake and concentration of Cd in MNVD water were higher than the World Health Organisation’s guideline values for the drinking water quality. The water quality of Manchar Lake was found degraded.     

Modeling Phosphate Influence on Arsenate Reduction Kinetics by a Freshwater Cyanobacterium

Arsenic speciation in natural surface-water systems can be highly impacted through biological processes that result in non-thermodynamically predicted species to dominate the system. In laboratory experiments, arsenate reduction by a freshwater cyanobacterium exhibited saturation kinetics increasingly inhibited by elevating solution phosphate concentrations. Approximately 100% arsenate reduction occurred by days 4, 7, and 10 in the low (0.35 μm), middle (3.5 μm), and high (35 μm) phosphate treatments, respectively, with maximum arsenate reduction rates ranged from 0.013 μmol As g C⁻¹ day⁻¹ in the high-phosphate treatment to 0.398 μmol As g C⁻¹ day⁻¹ in the low-phosphate treatment. Saturation kinetic models were utilized to evaluate the impact of cell growth and arsenate-phosphate uptake competition on arsenate reduction rates by the cyanobacterium. Results showed reduced arsenicals dominate arsenic speciation once growth reached steady state, indicating reduced arsenicals may dominate natural systems, even when considering conservatively high, abiotic arsenic reoxidation.     

Behaviour and Quantification Studies of Terbacil and Lenacil in Environmental Samples Using Cyclic and Adsorptive Stripping Voltammetry at Hanging Mercury Drop Electrode

The cyclic voltammograms of terbacil and lenacil at the hanging mercury drop electrode showed a single well defined four electron irreversible peak in universal buffer of pH 4.0 for both compounds. The peak potentials were shifted to more negative values on the increase of pH of the medium, implying the involvement of protons in the electrode reaction and that the proton transfer reaction precedes the proper electrode process. The four electron single peak may be attributed to the simultaneous reduction of carbonyl groups present in 2 and 4 in pyrimidine ring of terbacil and lenacil to the corresponding hydroxy derivative. Based on the interfacial adsorptive character of the terbacil and lenacil onto the mercury electrode surface, a simple sensitive and low cost differential pulse adsorptive stripping voltammetric procedure was optimized for the analysis of terbacil and lenacil. The optimal operational conditions of the proposed procedure were accumulation potential E _acc = −0.4 V, accumulation time t _acc = 80 s, scan rate = 40 mV s⁻¹, pulse amplitude = 25 mV using a universal buffer pH 4.0 as a supporting electrolyte. The linear concentration range was found to be 1.5 × 10⁻⁵ to 1.2 × 10⁻⁹ mol/l and 1.5 × 10⁻⁵ to 2.5 × 10⁻⁸ mol/l with the lower detection limit of 1.22 × 10⁻⁹ and 2.0 × 10⁻⁸ mol/l. The correlation coefficient and relative standard deviation values are found to be 0.942, 0.996, 1.64% and 1.23%, respectively, for 10 replicants. The procedure was successfully applied for determination of terbacil and lenacil in formulations, mixed formulations, environmental samples such as fruit samples and spiked water samples.     

Evaluation of levels, sources and distribution of toxic elements in PM10 in a suburban industrial region, Rio de Janeiro, Brazil

The Oswaldo Cruz Foundation Campus (FIOCRUZ), in a suburban region of the city of Rio de Janeiro, was selected as a case study to assess the pollution released from vehicle and industrial facilities in Basin III, the most polluted area of the city. Concentrations of particulate matter (PM10) and trace metals in airborne particles were determined in an intensive field campaign. The samplings were performed every six days for 24 h periods, using a PM10 high volume sampler, from September 2004 to August 2005. PM10 mass concentrations were determined gravimetrically and the metals by ICP-OES. For PM10, the arithmetic mean for the period is 169 ± 42 μg m⁻³ which is 3.4 times the national recommended standard of 50 μg m⁻³. Additionally, 51% of the samplings exceeded the recommended 24 h limit of 150 μg m⁻³. Ca, Mg, Fe, Zn and Al were the metals that presented the higher concentrations. The correlation matrix gave two main clusters and three significant principal components (PC). Both PC1 and PC2 are associated to crustal, vehicular and industrial emissions while PC3 is mainly associated to geological material. Enrichment factors for Zn, Cu, Cd and Pb indicate that for these elements, anthropic sources prevail over natural inputs. PM10 levels showed a good correlation with hospital admissions for respiratory diseases in children and elderly people.     

Solid phase extraction of gold(III) on Amberlite XAD-2000 prior to its flame atomic absorption spectrometric determination

A solid phase extraction method for the determination of gold(III) at trace levels by flame atomic absorption spectrometer (FAAS) was developed. The method was based on retention of gold as chloro complexes through the Amberlite XAD-2000. The effect of some analytical parameters including hydrochloric acid concentration, sample volume, sample and eluent flow rates, eluent volume, eluent concentration and interfering ions on the recovery of gold(III) was investigated. The retention of gold(III) from 1.5 mol l⁻¹ HCl solution and the recovery of gold with 0.07 mol l⁻¹ NH₃ solution were quantitative (≥95%). The relative standard deviation (RSD) was calculated as 3.2% (n = 10). The detection limit for gold was 2 μg l⁻¹. The accuracy was checked with the determination of gold spiked an artificial seawater and a pure copper samples.     

Estimation of Polish cigarettes contamination with cadmium and lead, and exposure to these metals via smoking

To estimate exposure to cadmium (Cd) and lead (Pb) through cigarette smoking, the concentrations of both metals in the blood or/and urine of smokers (20 cigarettes or more per day for 10 years or longer) and their non-smoking counterparts inhabiting an environmentally unpolluted area (Bialystok, Poland) were evaluated, as well as Cd and Pb contents in the cigarette brands (produced in Poland) smoked by the participants, including intact cigarettes, pre-smoking (tobacco, paper and filter) and post-smoking (butt, ash and smoke) cigarette components. Blood and urinary Cd concentrations in the smokers have been already reported by us to be 2–4 times higher than in the non-smokers (Galażyn-Sidorczuk et al. Polish Journal of Environmental Studies, 13 (Suppl.1):91–95, 2004). All the other measurements are the subject of the present paper. Pb concentration in the blood of the cigarette smokers (52.12 ± 15.51 μg l⁻¹) was higher by 29% than in the non-smokers (40.42 ± 11.19 μg l⁻¹). The mean Cd and Pb contents in the cigarettes were 0.6801 ± 0.1765 and 0.6853 ± 0.0746 μg per cigarette, respectively. Under cigarette burning, performed using a machine for self-acting burning, on average 33% of Cd and 11% of Pb present in the whole cigarette was released into the smoke. For Cd, unlike Pb, there was a high positive correlation between the metal content in cigarettes and tobacco and its release into the smoke. Moreover, the subjects smoking cigarettes containing the highest Cd amount had higher blood Cd concentration than smokers of other cigarette brands. The results give clear evidence that in the case of inhabitants of areas unpolluted with Cd and Pb habitual cigarette smoking, due to tobacco contamination, creates a serious source of chronic exposure to these metals, especially to Cd.