The impact of domestic wood burning on personal, indoor and outdoor levels of 1,3-butadiene, benzene, formaldehyde and acetaldehyde

The aim of this study was to quantify personal exposure and indoor levels of the suspected or known carcinogenic compounds 1,3-butadiene, benzene, formaldehyde and acetaldehyde in a small Swedish town where wood burning for space heating is common. Subjects (wood burners, n = 14), living in homes with daily use of wood-burning appliances were compared with referents (n = 10) living in the same residential area. Personal exposure and stationary measurements indoors and at an ambient site were performed with diffusive samplers for 24 h. In addition, 7 day measurements of 1,3-butadiene and benzene were performed inside and outside the homes. Wood burners had significantly higher median personal exposure to 1,3-butadiene (0.18 microg m(-3)) compared with referents (0.12 microg m(-3)), which was also reflected in the indoor levels. Significantly higher indoor levels of benzene were found in the wood-burning homes (3.0 microg m(-3)) compared with the reference homes (1.5 microg m(-3)). With regard to aldehydes, median levels obtained from personal and indoor measurements were similar although the four most extreme acetaldehyde levels were all found in wood burners. High correlations were found between personal and indoor levels for all substances (r(s) > 0.8). In a linear regression model, type of wood-burning appliance, burning time and number of wood replenishments were significant factors for indoor levels of 1,3-butadiene. Domestic wood burning seems to increase personal exposure to 1,3-butadiene as well as indoor levels of 1,3-butadiene and benzene and possibly also acetaldehyde. The cancer risk from these compounds at exposure to wood smoke is, however, estimated to be low in developed countries.     

Verifying emission factors and national POPs emission inventories for the UK using measurements and modelling at two rural locations

Different approaches are used to verify the adequacy of emission factors (EFs) and their use in emission inventories of persistent organic pollutants (POPs). The applicability of EFs was tested using atmospheric dispersion modelling to predict atmospheric concentrations of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) and resulting toxic equivalents (SigmaTEQ) and particulate matter <10 microm (PM(10)) in two rural locations in northern England (UK). The modelling was based on general assumptions of fuel composition, consumption and heating needs to simulate emissions of POPs from the domestic burning of coal and wood where ambient measurements were made in the winter of 1998. The model was used to derive the local contribution to ambient air concentrations, which were estimated independently based on comparative air measurements. The results support the hypothesis that in both villages, the majority of PAHs and the lower chlorinated PCDFs were locally released. The situation for PCBs and polychlorinated naphthalenes (PCNs) was different. While the EFs show the release of both compound groups from the domestic burning of coal and wood, the ambient levels of these "legacy POPs" in the villages were still clearly dominated by other sources. Rural areas relying mainly on fossil fuels can exceed the proposed UK ambient air quality standard for benzo[a]pyrene during winter. The measured EFs were then used to estimate the importance of the domestic burning of coal and wood to national emission inventories for these compound classes. Extrapolations to the UK suggest that the domestic burning of pure wood and coal were minor emitters for chlorinated POPs but contributed strongly to PAH and PM(10) levels in 2000. Finally, the UK's national POPs emission inventories based on source inventories and EF, as used here, were compared to estimates derived using the increase in atmospheric concentration of selected POPs.     

Occupational and indoor air exposure to persistent organic pollutants: a review of passive sampling techniques and needs

Exposure to persistent organic pollutants (POPs) and related compounds such as PCBs, brominated flame retardants, organochlorine pesticides and PAHs is regarded as an important environmental risk factor for humans. Recently concerns about POPs resulted in the international protocol called the Stockholm Convention on POPs. Air quality standards (indoor, outdoor and occupational) for PAHs and other POPs will also be applied in the EU in the future. This will bring requirements for monitoring, to check for compliance and to reduce human exposures to POPs. This can occur from point sources and in various microenvironments, indoors, outdoors and in workplaces. Monitoring can be undertaken either by an active (pumped) method or using a passive (diffusive) air sampling (PAS) device. To date, PAS for POPs have mainly been used as integrating (long-term) samplers for ambient (outdoor) air. However, there are several reasons to develop PAS for monitoring of POPs in occupational and indoor environments. We discuss the potential advantages, limitations and developments needed, so that PAS can be used reliably and routinely indoors and in occupational settings for POPs.     

不同木柴在两种条件下燃烧生成的颗粒物中多环芳烃的排放特性研究

将马尾松、赤桉、甜叶桉树和锦熟黄杨四种木柴,使用普通家用木柴燃烧加热炉在两种条件下进行燃烧,采集燃烧所排放的颗粒物样品并分析,获得了颗粒物中多环芳烃(Polycyclic Aromatic Hydrocarbons简写为PAHs)的排放因子及单个多环芳烃化合物的分布规律。结果显示:在颗粒物中检测出的多环芳烃化合物主要是分子量较大并被称为基因致毒性类的多环芳烃化合物,实验还发现:在四种木柴中,马尾松具有最高的多环芳烃化合物的排放因子,其次是赤桉和锦熟黄杨,最低的是甜叶桉树。两种不同的燃烧条件相比,慢燃烧比快燃烧所产生的总多环芳烃化合物和基因致毒性多环芳烃化合物的量都要高。     

云南省宣威市和富源县空气和土壤中多环芳烃污染水平研究

宣威市和富源县位于我国云南省东北部,是全世界肺癌发病率最高的地区之一。当地居民在不通风的房间内燃烧烟煤做饭或取暖造成了严重的室内空气污染。研究表明,长期暴露在燃煤造成的污染物中是导致两地居民肺癌持续高发的主要原因,多环芳烃是最可疑的致病因子之一。2008年1月,分别用聚胺脂泡沫和玻璃纤维滤膜采集了当地9个点位室内、室外空气中气相和颗粒物相中的多环芳烃,同时采集了对应点位的土壤样品。通过对样品的分析,考察了当地空气和土壤中多环芳烃的污染水平、特征以及来源。结果证明,当地空气和土壤中存在严重的多环芳烃污染,室内污染显著高于室外,然而随着当地工业的发展室外污染同样不可忽视,主成分分析结合比值法证明,当地室内外多环芳烃的主要污染源来自于煤炭的燃烧。对空气颗粒物和土壤中多环芳烃浓度进行了比较,对土壤中多环芳烃的来源进行了验证。     

Dioxins and polychlorinated biphenyls (PCDD/Fs and PCBs) in food from farms close to foot and mouth disease animal pyres

To control the outbreak of foot and mouth disease, which occurred in the UK in early 2001, a large number of farm animals were slaughtered. Where it was not possible to render or landfill the carcasses, they were destroyed by burning on open pyres, with wood, coal and other materials. Uncontrolled combustion such as this is known to produce small quantities of dioxins and an investigation was made into whether, as a result of the burning, there was an elevation in the concentrations of these compounds in food produced in the areas close to the pyres. With few exceptions, concentrations of PCDD/Fs and PCBs were within the expected ranges as predicted by reference data. No accumulation over time was evident from a repeat milk sampling exercise. Where elevated concentrations of PCDD/Fs and PCBs were found in chickens and eggs, they were in samples not destined for the food chain. Elevated levels in some samples of milk from Dumfries and Galloway were not found in earlier or later samples and may have been found as a result of a temporary feeding regime. Elevated concentrations in lamb from Carmarthenshire were from very young animals which would not have entered the food chain. There was no evidence of any significant increase in dietary exposure to PCDD/Fs and PCBs as a result of the FMD pyres.     

某石化化工行业聚集区室内外PM2.5中多环芳烃分布特征及来源

于非采暖季和采暖季分别采集某石化化工行业聚集城市中心城区室内外PM_(2.5)样品,采用高效液相色谱法分析PM_(2.5)上载带的16种PAHs,对其分布特征、来源以及室外PAHs污染对室内污染的贡献进行了初步探讨。结果表明,研究区域非采暖季和采暖季室外PM_(2.5)中ΣPAHs浓度日均值分别为36.3、294 ng/m~3,室内PM_(2.5)中ΣPAHs浓度分别为14.8、84.6 ng/m~3,均以4、5环PAHs为主;室内PAHs主要来自室外渗透污染,但同时明显存在室内排放源贡献;PAHs来源分析进一步证实研究区域PAHs主要来自煤炭、石油等不完全燃烧,采暖季煤炭燃烧源贡献更突出。     

Seasonal variation for the ratio of BaP to BeP at different sites in Great Xiamen Bay

From March 2008 to February 2009, PM(10) samples were collected and analyzed for polycyclic aromatic hydrocarbons (PAHs) at eight sampling sites in Great Xiamen Bay, China. Analyses of the seasonal and spatial variations of these compounds revealed the following results. Significantly high levels of PAHs were found in the winter compared to the summer, sometimes exceeding 100 ng m(-3), and the spatial variations were influenced most by the sampling site surroundings. Composition profiles of PAHs of an urban and a rural site were shown to be very similar with a positive correlation coefficient larger than 0.9 at the 0.01 level of significance for the same season. Diagnostic ratios, together with principal component and multiple linear regression analysis, showed that more PAHs were from grass/wood/coal combustion in winter than in other seasons. The ratios of benzo[a]pyrene to benzo[e]pyrene (BaP-BeP) in winter and fall were 0.6-1.7 times higher than those in spring and summer, suggesting the importance of local emissions of PAHs. The BaP-BeP ratios in Kinmen were generally lower than those in Xiamen, indicating that the aging degree of PAHs was higher in Kinmen than in Xiamen. The external input of PAHs from upwind urban and industrial areas was one of the key factors causing high levels of PAHs in PM(10) in Great Xiamen Bay in winter.     

Evaluation of the urban/rural particle-bound PAH and PCB levels in the northern Spain (Cantabria region)

The aim of the present study was to evaluate the polycyclic aromatic hydrocarbon (PAH) and polychlorinated biphenyl (PCB) levels in PM(10) and PM(2.5), at one rural and three urban sites in the Cantabria region (northern Spain). From all of these pollutants, benzo(a)pyrene is regulated by the EU air quality directives; its target value (1?ng/m(3)) was not exceeded. The concentration values of the studied organic pollutants at the studied sites are in the range of those obtained at other European sites. A comparison between the rural-urban stations was developed: (a) PAH concentration values were lower in the rural site (except for fluorene). Therefore, the contribution of local sources to the urban levels of PAHs seems relevant. Results from the coefficient of divergence show that the urban PAH levels are influenced by different local emission sources. (b) PCB rural concentration values were higher than those found at urban sites. Because no local sources of PCBs were identified in the rural site, the contribution of more distant emission sources (about 40?km) to the PCB levels is considered to be the most important; the long-range transport of PCBs does not seem to be significant. Additionally, local PAH tracers were identified by a triangular diagram: higher molecular weight PAHs in Reinosa, naphthalene in Santander and anthracene/pyrene in Castro Urdiales. A preliminary PAH source apportionment study in the urban sites was conducted by means of diagnostic ratios. The ratios are similar to those reported in areas affected by traffic emissions; they also suggest an industrial emission source at Reinosa.     

Distribution and sources of polycyclic aromatic hydrocarbons in Wuhan section of the Yangtze River, China

Polycyclic aromatic hydrocarbons (PAHs) are important organic contaminants with great significance for China, where coal burning is the main source of energy. In this study, concentrations, distribution between different phases, possible sources and eco-toxicological effect of PAHs of the Yangtze River were assessed. PAHs in water, suspended particulate matters (SPM) and sediment samples at seven main river sites, 23 tributary and lake sites of the Yangtze River at the Wuhan section were analyzed. The total concentrations of PAHs in the studied area ranged from 0.242 to 6.235 μg/l in waters and from 31 to 4,812 μg/kg in sediment. The average concentration of PAHs in SPM was 4,677 μg/kg, higher than that in sediment. Benzo(a)pyrene was detected only at two stations, but the concentrations were above drinking water standard. The PAHs level of the Yangtze River was similar to that of some other rivers in China but higher than some rivers in foreign countries. There existed a positive relationship between PAHs concentrations and the TOC contents in sediment. The ratio of specific PAHs indicated that PAHs mainly came from combustion process, such as coal and wood burning. PAHs may cause potential toxic effect but will not cause acute biological effects in sedimentary environment of the Wuhan section of the Yangtze River.     

Application of CMB model for source apportionment of polycyclic aromatic hydrocarbons (PAHs) in coastal surface sediments from Rizhao offshore area, China

Polycyclic aromatic hydrocarbons (PAHs) in coastal surface sediments from Rizhao offshore area were analyzed by gas chromatography–mass spectrometry. A chemical mass balance (CMB) model developed by the U.S. Environmental Protection Agency (EPA), CMB8.2, was used to apportion sources of PAHs. Seven possible sources, including coal residential, coal power plant, diesel engines exhaust, gasoline engines exhaust, coke oven, diesel oil leaks, and wood burning, were chosen as the major contributors for PAHs in coastal surface sediments. To establish the fingerprints of the seven sources, source profiles were collected from literatures. After including degradation factors, the modified model results indicate that diesel oil leaks, diesel engines exhaust, and coal burning were the three major sources of PAHs. The source contributions estimated by the EPA’s CMB8.2 model were 9.25%, 15.05%, and 75.70% for diesel oil leaks, diesel engines exhaust, and coal burning, respectively.     

Impact of urbanization on the concentrations and distribution of organic contaminants in boreal lake sediments

The main goal of this study was to evaluate the impacts of a middle-sized Finnish urban area on the quality of sediments in an adjacent boreal lake. We investigated the sources and distribution of organic pollutants (polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs)) in the sediments from urban stormwater traps and from Lake Vesijärvi. Grab surface sediment samples were taken from Lake Vesijärvi at various distances (25–2,000 m) from four major stormwater drainage outlets and at 15 urban stormwater traps in areas with different degrees of urbanization. These samples were analysed for 16 PAHs and 28 PCBs with gas chromatography–mass spectrometry. The concentrations of pollutants in the lake sediments were elevated in the vicinity of the urban shore (∑PAH 3–16, ∑PCB up to 0.02–0.3 mg/kg dw) and decreased as a function of distance (∑PAH 0.1–2.5, ∑PCB 0.01–0.3 mg/kg dw at a distance of more than 500 m from the shore), whereas contamination levels in suburban areas were notably lower (∑PAH 0.1–3, ∑PCB?<?LOQ–0.03 mg/kg dw; did not decline with distance). Possible sources and pathways of contamination were also investigated. The majority of stormwater trap sediments contained predominantly asphalt-derived PAHs due to pulverized pavement. PAHs in lake sediments were of pyrogenic origin, including the combustion of gasoline, diesel and coal. Suggested pathways of lake contamination are urban runoff discharge, boat traffic and atmospheric deposition.     

Sources of potentially toxic elements and organic pollutants in an urban area subjected to an industrial impact

Urban and industrial development has caused a major impact on environmental soil quality. This work assesses the extent and severity of contamination in a small urban area subjected to an industrial impact and identifies the major anthropogenic inputs. Twenty-six soil samples were collected from agricultural and urban sites, and concentrations of potentially toxic elements (As, Cd, Cu, Cr, Fe, Mn, Ni, Pb and Zn), PAHs and PCBs, were determined. In spite of the low median concentrations observed, some sites represent a potential hazard for human health and ecosystems. Concentrations of contaminants were higher than those found in a nearby city, indicating that the study area is affected by the surrounding industry. The use of multivariate statistical analyses allowed for the identification of the main factors controlling the variability of potentially toxic elements and organic pollutants in the soils. The presence of Cr, Fe, Mn and Ni was associated with geogenic inputs, and Cu, Pb, Zn, As, PAHs and PCBs were associated with anthropogenic inputs. Industry and traffic were the most important anthropogenic sources. Soil characteristics were identified as important factors controlling the spatial variability of elements, both from recognised natural and anthropogenic origin. Differences between land uses were observed, which may be attributed to both management practices and proximity to sources.     

Mussel watch program for organic contaminants along the Korean coast, 2001–2007

The level and extent of organic contaminants along the Korean coast were estimated through the mussel watch program, established in 2001. Mussels and oysters were collected at 20 sites along the Korean coast in 2001 and at 25 sites from 2002 to 2007. The mussel tissues were analyzed for PCBs, organochlorine presticides, PAHs, BTs, and PCDD/Fs. PCBs, PAHs, BTs, and PCDD/Fs were ubiquitous contaminants along the Korean coast, showing mean detection frequencies of more than 95% over 7 years. The concentrations of organic contaminants in mussels along the Korean coast were relatively low or moderate compared with foreign studies. Concentrations of DDTs, PCBs, and PCDD/Fs were below the action or maximum levels for humans established by USFDA and EU. Elevated concentrations above the 85th percentile were found for PCBs, PAHs, BTs, and PCDD/Fs at sites near industrial complexes or big harbors, for HCHs at sites near non-industrial complexes, and for DDTs at sites near both non-industrial and industrial complexes. Using two nonparametric tests to assess temporal trends, the Spearman test revealed that BTs and PCDD/Fs had significant decreasing trends at four sites (Gwangyang Bay, Cheonsu Bay, Garorym Bay, and the Incheon coast) and at six sites (Hupo coast, Guryongpo coast, eastern part of Geojedo, Gunsan coast, Garorym Bay, and Asan Bay), respectively.     

Indoor and outdoor concentrations of fine particles, particle-bound PAHs and volatile organic compounds in Kaunas, Lithuania

This complex study presents indoor and outdoor levels of air-borne fine particles, particle-bound PAHs and VOCs at two urban locations in the city of Kaunas, Lithuania, and considers possible sources of pollution. Two sampling campaigns were performed in January-February and March-April 2009. The mean outdoor PM(2.5) concentration at Location 1 in winter was 34.5 ± 15.2 μg m(-3) while in spring it was 24.7 ± 12.2 μg m(-3); at Location 2 the corresponding values were 36.7 ± 21.7 and 22.4 ± 19.4 μg m(-3), respectively. In general there was little difference between the PM concentrations at Locations 1 and 2. PM(2.5) concentrations were lower during the spring sampling campaign. These PM concentrations were similar to those in many other European cities; however, the levels of most PAHs analysed were notably higher. The mean sum PAH concentrations at Locations 1 and 2 in the winter campaign were 75.1 ± 32.7 and 32.7 ± 11.8 ng m(-3), respectively. These differences are greater than expected from the difference in traffic intensity at the two sites, suggesting that there is another significant source of PAH emissions at Location 1 in addition to the traffic. The low observed indoor/outdoor (I/O) ratios indicate that PAH emissions at the locations studied arise primarily from outdoor sources. The buildings at both locations have old windows with wooden frames that are fairly permissive in terms of air circulation. VOC concentrations were mostly low and comparable to those reported from Sweden. The mean outdoor concentrations of VOC's were: 0.7 ± 0.2, 3.0 ± 0.8, 0.5 ± 0.2, 3.5 ± 0.3, and 0.2 ± 0.1 μg m(-3), for benzene, toluene, ethylbenzene, sum of m-, p-, o-xylenes, and naphthalene, respectively. Higher concentrations of VOCs were observed during the winter campaign, possibly due to slower dispersion, slower chemical transformations and/or the lengthy "cold start" period required by vehicles in the wintertime. A trajectory analysis showed that air masses coming from Eastern Europe carried significantly higher levels of PM(2.5) compared to masses from other regions, but the PAHs within the PM(2.5) are of local origin. It has been suggested that street dust, widely used for winter sanding activities in Eastern and Central European countries, may act not only as a source of PM, but also as source of particle-bound PAHs. Other potential sources include vehicle exhaust, domestic heating and long-range transport.     

Health risk assessment of occupational exposure to particulate-phase polycyclic aromatic hydrocarbons associated with Chinese, Malay and Indian cooking

Food cooking using liquefied petroleum gas (LPG) has received considerable attention in recent years since it is an important source of particulate air pollution in indoor environments for non-smokers. Exposure to organic compounds such as polycyclic aromatic hydrocarbons (PAHs) contained in particles is of particular health concern since some of these compounds are suspected carcinogens. It is therefore necessary to chemically characterize the airborne particles emitted from gas cooking to assess their possible health impacts. In this work, the levels of fine particulate matter (PM(2.5)) and 16 priority PAHs were determined in three different ethnic commercial kitchens, specifically Chinese, Malay and Indian food stalls, where distinctive cooking methods were employed. The mass concentrations of PM(2.5) and PAHs, and the fraction of PAHs in PM(2.5) were the highest at the Malay stall (245.3 microg m(-3), 609.0 ng m(-3), and 0.25%, respectively), followed by the Chinese stall (201.6 microg m(-3), 141.0 ng m(-3), and 0.07%), and the Indian stall (186.9 microg m(-3), 37.9 ng m(-3), and 0.02%). This difference in the levels of particulate pollution among the three stalls may be attributed to the different cooking methods employed at the food stalls, the amount of food cooked, and the cooking time, although the most sensitive parameter appears to be the predominant cooking method used. Frying processes, especially deep-frying, produce more air pollutants, possibly due to the high oil temperatures used in such operations. Furthermore, it is found that frying, be it deep-frying at the Malay stall or stir-frying at the Chinese stall, gave rise to an abundance of higher molecular weight PAHs such as benzo[b]fluoranthene, indeno[1,2,3-cd]pyrene and benzo[g,h,i]perylene whereas low-temperature cooking, such as simmering at the Indian stall, has a higher concentration of lower molecular weight PAHs. In addition, the correlation matrices and diagnostic ratios of PAHs were calculated to determine the markers of gas cooking. To evaluate the potential health threat due to inhalation exposure from the indoor particulate pollution, excess lifetime cancer risk (ELCR) was also calculated for an exposed individual. The findings suggest that cooking fumes in the three commercial kitchens pose adverse health effects.     

A preliminary investigation of BDE-209, OCPs, and PAHs in urban road dust from Yangtze River Delta, China

Urban road dust samples were collected from different land use areas in Suzhou, Wuxi, and Nantong, Yangtze River Delta, China. The dust samples were analyzed for the levels and compositional profiles of deca-polybrominated diphenyl ethers (Deca-BDE), 22 organochlorine pesticides (OCPs), and 16 polycyclic aromatic hydrocarbons (PAHs). The levels of BDE-209, ∑OCPs, and ∑PAHs in samples ranged from 4.01–1,439 μg/kg, 3.15–615 μg/kg, and 2.24–58.2 mg/kg, respectively. PAHs were the predominant target compounds in road dust samples, comprising on average 97.7 % of total compounds. The spatial gradient of the pollutants (commercial/residential area> industrial area > urban park concentrations) was observed in the present study. The results indicated that the levels of BDE-209, OCPs, and PAHs observed in road dust were usually linked to anthropogenic activities in the urban environment. In addition, there might be a reflection of current usage or emissions of OCPs in urban environment.     

Quantitation of persistent organic pollutants adsorbed on plastic debris from the Northern Pacific Gyre's "eastern garbage patch"

Floating marine plastic debris was found to function as solid-phase extraction media, adsorbing and concentrating pollutants out of the water column. Plastic debris was collected in the North Pacific Gyre, extracted, and analyzed for 36 individual PCB congeners, 17 organochlorine pesticides, and 16 EPA priority PAHs. Over 50% contained PCBs, 40% contained pesticides, and nearly 80% contained PAHs. The PAHs included 2, 3 and 4 ring congeners. The PCBs were primarily CB-11, 28, 44, 52, 66, and 101. The pesticides detected were primarily p,p-DDTs and its metabolite, o,p-DDD, as well as BHC (a,b,g and d). The concentrations of pollutants found ranged from a few ppb to thousands of ppb. The types of PCBs and PAHs found were similar to those found in marine sediments. However, these plastic particles were mostly polyethylene which is resistant to degradation and although functioning similarly to sediments in accumulating pollutants, these had remained on or near the ocean surface. Particles collected included intact plastic items as well as many pieces less than 5 mm in size.     

Occurrence and distribution of polycyclic aromatic carbons in sludges from wastewater treatment plants in Guangdong, China

In this study, the occurrence and distribution of polycyclic aromatic hydrocarbons (PAHs) were investigated in six sludge samples collected from Guangdong Province, China. Concentrations of PAHs varying from 2,534.1 to 6,926.6 μg kg^???1 (dry sludge) were observed in three municipal wastewater treatment plants with phenanthrene (Phe), fluoranthene, and pyrene being the main compounds. In addition, 682.6 μg kg^???1 PAHs were detected in one sludge sample from a food processing plant, with fluorene, Phe, and chrysene being the main components. No PAHs were detected in sludge samples obtained from two cosmetic plants. The levels and distributional characteristics of PAHs, polychlorinated biphenyls (PCBs), and polycyclic musks (PMs) from the samples were also compared. The results of this comparison indicated that petrochemical refineries and road traffic played important roles in the PAH loads in sludge, while PMs primarily originated from domestic wastewater and industrial wastewater from cosmetic plants. Finally, the presence of 98.8 μg kg^???1 PCBs in sludge suggested diffusional emission sources from electrical components containing PCBs.     

Characteristics and sources of atmospheric polycyclic aromatic hydrocarbons (PAHs) in Shanghai, China

A field campaign was conducted to measure and analyze 13 polycyclic aromatic hydrocarbons (PAHs) in six major zones in the city of Shanghai, P.R. China from August 2006 to April 2007. Ambient air samples were collected seasonally using passive air samplers, and gas chromatography–mass spectroscopy was used in this field campaign. The results showed that there was a sequence of 13 PAHs at Phen > FA > Pyr > Chr > Fl > An > BaA > BbFA > BghiP > IcdP > BkFA > BaP > DahA and the sum of these PAHs is 36.01 ± 10.85 ng/m³ in gas phase. FL, Phen, FA, Pyr, and Chr were the dominant PAHs in gas phase in the city. They contributed 90% of total PAHs in the gas phase. Proportion of measured PAHs with three, four, five, and six rings to total PAHs was 53%, 42%, 3%, and 2%, respectively. The highest concentration of ΣPAHs (the sum of 13 PAHs) occurred in the wintertime and the lowest was in the summer. This investigation suggested that traffic, wood combustion, and metal scrap burn emissions were dominant sources of the concentrations of PAHs in six city zones compared with coal burning and industry emissions. Further, the traffic emission sources of PAHs in the city were attributed mostly to gasoline-powered vehicles compared with diesel-powered vehicles. It was revealed that the seasonal changes in PAHs in the city depended on different source types. Metal scrap burn was found to be the major source of PAHs during the autumn, while the PAH levels in the atmosphere for winter and spring seasons were mainly influenced by wood and biomass combustion. Comparisons of PAHs among different city zones and with several other cities worldwide were also made and discussed.