Solid phase extraction of gold(III) on Amberlite XAD-2000 prior to its flame atomic absorption spectrometric determination

A solid phase extraction method for the determination of gold(III) at trace levels by flame atomic absorption spectrometer (FAAS) was developed. The method was based on retention of gold as chloro complexes through the Amberlite XAD-2000. The effect of some analytical parameters including hydrochloric acid concentration, sample volume, sample and eluent flow rates, eluent volume, eluent concentration and interfering ions on the recovery of gold(III) was investigated. The retention of gold(III) from 1.5 mol l⁻¹ HCl solution and the recovery of gold with 0.07 mol l⁻¹ NH₃ solution were quantitative (≥95%). The relative standard deviation (RSD) was calculated as 3.2% (n = 10). The detection limit for gold was 2 μg l⁻¹. The accuracy was checked with the determination of gold spiked an artificial seawater and a pure copper samples.     

Determination of organophosphorus pesticides and related compounds in water samples by membrane extraction and gas chromatography

A membrane extraction-gas chromatography method was developed fordetermination of organophosphorus pesticides and related compounds including methamidophos, DDVP, dimethoate, methyl parathion, parathion, thiophosphoric acid trimethyl ester, and thiophosphoramidic acid dimethyl ester in water samples. In thismethod, surface-modified acetic cellulose membranes were used to extract the target analytes in water samples, the extracted analytes were back-extracted into a small amount of methanol, andgas chromatography with pulsed flame photometric detector (GC-PFPD) was used to determine the concentrations of targetanalytes in the extracts. The recoveries obtained for thetarget analytes spiked into the water samples ranged from 66to 94%. The method detection limit for each target analyte was 0.05 g L^-1. The method developed in this study had shown the advantages of being cheap, simple, fast, and reliable. It had been used successfully to determine the concentrations of target analytes in river water samples.     

New procedures for simultaneous determination of mesotrione and atrazine in water and soil. Comparison of the degradation processes of mesotrione and atrazine

A method for the determination of residues of mesotrione, atrazine and its degradation products: deethylatrazine, hydroxyatrazine, deisopropylatrazine, desethyldesisopropylatrazine in a variety of water and soil matrices has been developed. Mesotrione is a new selective herbicide for use in corn, which has been substituted for atrazine, which has been banned in European Union countries since 2007. Although atrazine has not been used for three vegetative periods, it is still detected in the environment. The analysis was conducted by means of ultra-high-pressure liquid chromatography with ultraviolet detection and liquid chromatography with diode array detection. The procedures for analyte separation from water and soil matrices were also established. The optimal conditions for solid-phase extraction (SPE) were determined. The recoveries were compared with that obtained by means of SPE. Method fortification recoveries from water samples averaged 78–97% and for soil 80–97% depending on the analyte and type of sample. The limits of detection were 0.04–0.61 μg/L for water samples and for soil samples 0.02–0.88 μg/g. The soil samples were collected in spring 2009 from three different fields with water samples being made from effluents from these fields. Samples collection was conducted in the day of mesotrione (Callisto 100SC) application and then done weekly, until the mesotrione concentration was below the limit of quantification. The results enabled the monitoring of mesotrione degradation in soil and its permeability into surface waters; simultaneously, the same studies were conducted for atrazine.     

Analysis of Polycyclic Aromatic Hydrocarbons in Street Soil Dust in Kumasi Metropolis of Ghana

Concentrations of polycyclic aromatic hydrocarbons (PAHs) in street soil dust from streets in Kumasi Metropolis in the Ashanti Region of the Republic of Ghana have been measured in this study. The concentrations of the various types of PAHs identified in this study are as follows: Naphthalene (m/e 128) – 41,700 μg/kg, Acenaphthylene (m/e 152) – 99,300 μg/kg, Acenaphthene (m/e 154) – 111,200 μg/kg, Fluorene (m/e 166) – 8,900 μg/kg, Carbazole (m/e 167) – 3,500 μg/kg, phenathrene (m/e 178) – 12,900 μg/kg, Anthracene (m/e 178) – 5,400 μg/kg, Fluoranthene (m/e 202) – 16,200 μg/kg, Pyrene (m/e 202) – 15,000 μg/kg, Benzo[a]anthracene (m/e 228) – 13,800 μg/kg, Chrysene (m/e 228) – 33,600 μg/kg, Benzo[k]fluoranthene (m/e 252) – 45,700 μg/kg, Benzo[a]pyrene (m/e 252) – 27,900 μg/kg, Perylene (m/e 252) – 57,200 μg/kg and Benzo[g, h, i]perylene (m/e 276) – 47,000 μg/kg. The results of the study shows that road users, like resident living in buildings within these areas, those engaged in commercial activities like hawking, and the general public are at risk of exposure to the toxic effects of the various types of PAHs from the exhaust of vehicles into the environment. According to these results, there is the potential for exposure to high levels of PAHs for road users and those living in urban environments or along highways.     

Comparative Metal Distribution in Hair of Pakistani and Libyan Population and Source Identification by Multivariate Analysis

Using nitric acid-perchloric acid wet digestion based FAAS method ten selected metals (Cd, Co, Cr, Fe, K, Mn, Na, Ni, Pb and Zn) were determined in the scalp hair of male Pakistani and Libyan donors (n = 62), between 3–54 years age and residing in typical urban areas. The study was taken up to identify sources of metal distribution in two diverse population segments exposed to different environments. Sodium emerged with the highest mean hair concentration of 511.0 μg/g and 496.9 μg/g for Libyan and Pakistani donors respectively, followed by K, at 266.2 μg/g and 242.4 μg/g for the two donor categories. Cadmium showed the lowest mean hair concentration for both Pakistani (0.380 μg/g) and Libyan (0.530 μg/g) donors. Levels of Na, K, Pb, Cr and Cd were higher in hair of Libyan donors compared with Pakistani counterparts which showed higher comparative levels of Zn, Fe, Co, Ni and Mn. Strong metal-to-metal correlations were found between Na–K (r = 0.638) and Cd–Co (r = 0.574) for Pakistani donors, while for Libyan donors, Na–K (r = 0.680) and Fe–Mn (r = 0.624) correlations emerged as strongly significant. Only K was found to have a strong positive correlation (r = 0.611) with age for Pakistani donors while this correlation was significantly negative (r = −0.500) for Libyan donors, probably arising from individual food habits. Other metals showed no viable relationship with age. Principal Component Analysis (PCA) and Cluster Analysis (CA) of the data evidenced food, industrial emissions and automobile emissions as possible sources of metal distribution. The results of the present study are compared with those reported for subjects from other regions of the world.     

Distribution of Metals in the Edible Plants Grown at Jajmau, Kanpur (India) Receiving Treated Tannery Wastewater: Relation with Physico-Chemical Properties of the Soil

The implications of metal contamination of agricultural soils due to long term irrigation with treated industrial wastewater and their subsequent accumulation in the vegetables/crops growing on such soils has been assessed in an area of industrial complex, Jajmau, Kanpur (India). Physico-chemical properties of the soil were also studied. The soil and vegetables/crops were sampled from an area of 2100 acre agricultural land and analyzed for physico-chemical properties and metal accumulation in different parts of the plants. The comparison of the data of physico-chemical properties of control and contaminated soil showed that salinity, electrical conductivity, available phosphorous, sodium and potassium content (both water soluble and exchangeable) were found high in contaminated soil. The analysis of plant available metal content in the soil showed the highest level of Fe, which ranged from 529.02 to 2615 μg g⁻¹ dw and lowest level of Ni (3.12 to 10.51 μg g⁻¹ dw). The analysis of the results revealed that accumulation of toxic metal Cr in leafy vegetables was found more than fruit bearing vegetables/crops. Thus, it is recommended that the leafy vegetables are unsuitable to grow in such contaminated sites. It is important to note that toxic metal, Ni was not detected in all the plants. The edible part of the vegetables (under ground) such as, garlic (19.27 μg g⁻¹ dw), potato (11.81 μg g⁻¹ dw) and turmeric (20.86 μg g⁻¹ dw) has accumulated lowest level of toxic metal, Cr than leafy and fruit bearing vegetables. In some fruit part of vegetables such as, bitter gourd, egg plant, jack tree, maize and okra, the accumulation of Cr was not detected and may be grown in this area.     

Trace Metal Levels in Mussels (Mytilus Galloprovincialis L. 1758) from Turkish Aegean Sea Coast

Bio-monitoring of some heavy metal levels (Cd, Pb, Zn, Cu) in whole edible soft parts of Mytilus galloprovincialis (L. 1758) was conducted in Turkish Aegean Sea coast during the period of September 2002–August 2003 seasonally. Moreover, some physico-chemical environmental parameters, also have been analysed in the same region. The values of some physico-chemical environmental parameters in coastal waters of Turkish Aegean Sea were changed between; 9.0–27.0 ^∘C for temperature, 31.93–40.45 psu for salinity, 7.35–8.48 for pH and 4.05–9.50 mg/l for dissolved oxygen. The levels of trace elements in whole edible soft parts including interstitial fluids of Mediterranean mussels M. galloprovincialis (L. 1758), sampled from 6 different regions of Turkish Aegean Sea coast have ranged between; 0.04–0.52 μg Cd/g wet weight, 0.49–1.72 μg Pb/g w.w., 0.95–1.85 Cu/g w.w., 16.11–37.15 μg Zn/g w.w. The highest values for all trace metals (Cd, Pb, Zn, Cu) were measured in inner part of Izmir Bay (station 3) and lowest in Sigacik and Gulluk Bay (station 5, 6). Generally heavy metal levels are lower than the results in soft mussel tissues reported from Mediterranean regions.     

Estimation of Polish cigarettes contamination with cadmium and lead, and exposure to these metals via smoking

To estimate exposure to cadmium (Cd) and lead (Pb) through cigarette smoking, the concentrations of both metals in the blood or/and urine of smokers (20 cigarettes or more per day for 10 years or longer) and their non-smoking counterparts inhabiting an environmentally unpolluted area (Bialystok, Poland) were evaluated, as well as Cd and Pb contents in the cigarette brands (produced in Poland) smoked by the participants, including intact cigarettes, pre-smoking (tobacco, paper and filter) and post-smoking (butt, ash and smoke) cigarette components. Blood and urinary Cd concentrations in the smokers have been already reported by us to be 2–4 times higher than in the non-smokers (Galażyn-Sidorczuk et al. Polish Journal of Environmental Studies, 13 (Suppl.1):91–95, 2004). All the other measurements are the subject of the present paper. Pb concentration in the blood of the cigarette smokers (52.12 ± 15.51 μg l⁻¹) was higher by 29% than in the non-smokers (40.42 ± 11.19 μg l⁻¹). The mean Cd and Pb contents in the cigarettes were 0.6801 ± 0.1765 and 0.6853 ± 0.0746 μg per cigarette, respectively. Under cigarette burning, performed using a machine for self-acting burning, on average 33% of Cd and 11% of Pb present in the whole cigarette was released into the smoke. For Cd, unlike Pb, there was a high positive correlation between the metal content in cigarettes and tobacco and its release into the smoke. Moreover, the subjects smoking cigarettes containing the highest Cd amount had higher blood Cd concentration than smokers of other cigarette brands. The results give clear evidence that in the case of inhabitants of areas unpolluted with Cd and Pb habitual cigarette smoking, due to tobacco contamination, creates a serious source of chronic exposure to these metals, especially to Cd.     

The American Dipper as a Bioindicator of Selenium Contamination in a Coal Mine-Affected Stream in West-Central Alberta, Canada

Elevated levels of selenium have been found in water and aquatic biota downstream from two open-pit coal mines in the Rocky Mountain foothills of Alberta. Birds are particularly sensitive to excessive dietary selenium. However, there is relatively little information on selenium accumulation in birds' eggs on fast-flowing mountain streams. We determined levels of selenium in water samples, caddisfly larvae and eggs of American dippers (Cinclus mexicanus) nesting on the Gregg River, downstream from the mines, and on reference streams in the same general vicinity. Selenium levels (mean, 95% confidence limits) in water samples and caddisflies collected from sites near dipper nests on the Gregg River (water: 4.26, 1.90–9.56 μg L⁻¹; caddisflies: 8.43, 7.51–9.46 μg g dry wt⁻¹) were greater than those collected from sites near nests on reference rivers (water: 0.38, 0.21–0.71 μg L⁻¹; caddisflies: 4.65, 4.35–4.97 μg g dry wt⁻¹). The mean (± 1SE) selenium level in dipper eggs from the Gregg River (6.3 ± 0.2 μg g⁻¹ dry wt) was significantly higher than it was in eggs from reference streams (4.9 ± 0.2 μg g⁻¹ dry wt). Concentrations of selenium in eggs were significantly correlated with those in water samples (r = 0.45). The maximum selenium level in eggs from the Gregg River (9.0 μg g⁻¹) may have been high enough to warrant concern from an ecotoxicological perspective. The American dipper can serve as a useful bioindicator of selenium contamination in mountainous, lotic ecosystems.     

Arsenic and Other Metal Contamination of Groundwaters in the Industrial Area of Thessaloniki, Northern Greece

In groundwater, used for drinking water supply in the greater industrial area of Thessaloniki, in Northern Greece, concentrations of total arsenic exceeded the WHO provisional guideline value and the EU maximum contaminant level (MCL) of 10 μg/L. The concentration of total arsenic was in the range between 4–130 μg/L, whereas the median value was 36 μg/L and the average concentration 46 μg/L. Nine out of the eleven wells contained total arsenic at concentration higher than 10 μg/L and it should be stressed that 6 of them contain arsenic at concentrations between 10 (new MCL) and 50 μg/L (previous MCL). The examined groundwaters were found to contain elevated concentrations of manganese and phosphate. Arsenic had a positive correlation with the pH, indicating the possible effect of pH on arsenic mobilisation. These findings emerge the problem of contamination from arsenic, since, according to the EU directive 98/83, all drinking water sources within the European Union should have achieved compliance with the new limits by 12/2003, implying that the situation requires urgent remedial action.     

Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

Distribution of heavy metals in surface water of Ranipet industrial area in Tamil Nadu, India

Ranipet industrial area is about 120 km from Chennai on Chennai-Bangalore highway and is a chronic polluted area identified by Central Pollution Control Board of India. It is one of the biggest exporting centers of tanned leather in India. The total number of industries located in and around Ranipet town are 240 tanneries along with ceramic, refractory, boiler auxiliaries plant, and chromium chemicals. Studies were carried out to find out the contamination of surface water bodies due to industrial effluents. The results reveal that the surface water in the area is highly contaminated showing very high concentrations of some of the heavy/toxic metals like Cadmium ranging from 0.2 to 401.4 μg/l (average of 51.1 μg/l), Chromium 2.4–1,308.6 (average of 247.2 μg/l), Copper 2.1–535.5 μg/l (average of 95.5 μg/l), Nickel 1.6–147.0 μg/l (average of 36.7 μg/l), Lead 6.4–2,034.4 μg/l (average of 467.8 μg/l) and Zinc 20.8–12,718.0 μg/l (average of 3,760.4 μg/l). The concentration levels of these metals are much above the permissible limits in surface water and are health hazards especially for the people working in the tannery industries. It was observed that the people in the area are seriously affected and suffering from occupational diseases such as asthma, chromium ulcers and skin diseases. Distribution of metals, their contents at different locations, and their effects on human health are discussed in this paper.     

Isolation and Identification of Enterococci from Seawater Samples: Assessment of Their Resistance to Antibiotics and Heavy Metals

A hundred Enterococcus strains were isolated from seawater samples collected from coastal areas of Istanbul. Isolates were identified to the species level using standard biochemical tests specified by Facklam and Collins. The species distribution was as follows Enterococcus faecalis (96%), Enterococcus gallinarum (3%) and Enterococcus solitarius (1%). The resistance of bacteria to both heavy metals (zinc [Zn], iron [Fe], cadmium [Cd], chrome [Cr], cobalt [Co]) and antibiotics (ampicillin 10 μg [AP], penicillin G 10 Units [PG], gentamycin 10 μg [GM], streptomycin 10 μg [S], chloramphenicol 10 μg [C], erythromycin 15 μg [E], kanamycin 30 μg [K], amikacin 30 μg [AK], nalidixic acid 30 μg [NA], and vancomycin 30 μg [VA]) was evaluated. None of the strains was resistant to VA. It was found that among the 100 isolates, those that exhibit resistance to antibiotics, particularly NA, S and K, were also resistant all the heavy metals tested. To our knowledge this is the first report focusing on determination of resistance of environmental enterococci found in Istanbul against heavy metals and antibiotics. Thus, combined expressions of antibiotic and heavy metal resistance may help to reinforce ecological and epidemiological studies and to determine the role of these strains in antibiotic and heavy metal resistance dissemination.     

Sediment and Suspended Matter Lead Contamination in the Gulf of Kavala, Greece

Sediment and suspended particulate matter samples from 24 stations in the Gulf of Kavala have been examined for lead contamination. Grain size analysis and organic matter content were also performed. Total – anthropogenic sediment lead concentrations and enrichment factors at stations close to harbors and chemical industries were found higher (up to 209–135μg/g and 4.12 respectively), in relation to concentrations from the rest of the coastal zone. In the above areas, increased suspended particulate lead in the bottom of the water column was also recorded (up to 109μg/g). Total sediment lead concentrations composed of high natural Pb background increased with decreasing grain size, suggesting their association with the fine fractions of the sediments (31.1–66.0% mud presence) and the organic matter content (6–9% higher values). Overall, higher total lead concentrations in the sediments, determined by this work, appear to be significantly different from those reported for the Gulf of Kavala in previous studies and similar to those detected in other highly contaminated eastern Mediterranean coastal areas.     

Investigation of heavy metal contaminations in the lower Sakarya river water and sediments

In this work, water and sediment samples were collected from three different stations located along the Sakarya river between May and September 2003. Lead, copper, chromium, zinc, nickel and cadmium concentrations were determined by using solvent extraction and flame atomic absorption spectrometric method. The results show that differences based upon sampling times, regions, sediment and water samples were observed. The mean levels of copper, nickel, chromium, lead, cadmium, zinc for sediment samples are; 4.630 μg g⁻¹, 13.520 μg g⁻¹, 8.780 μg g⁻¹, 2.550 μg g⁻¹, 9.990 μg g⁻¹ and for water samples are; 0.851 μg g⁻¹, 1.050 μg g⁻¹, 0.027 μg g⁻¹, 1.786 μg g⁻¹, 0.236 μg g⁻¹, 0.173 μg g⁻¹, respectively.     

Organochlorine pesticides and polychlorinated biphenyl residues in reared and wild Dicentrarchus labrax from the Mediterranean Sea (Sicily, Italy)

The aim of this research was to compare the levels of organochlorine pesticides and PCBs in samples of Dicentrarchus labrax living in the Straits of Messina with samples cultivated in cages in the Mediterranean Sea. Muscles and liver tissues sampled over the months, within the same year, were analyzed. The quantitative determination of the organochlorine compounds was performed by GC-ECD and confirmed with GC–MS. The results showed that the concentrations of DDTs in muscles and livers as such of reared sea bass were in the range 0.2–1.3 μg/kg and 9.6 –48.4 μg/kg, respectively. In wild fish the concentrations of DDTs were very much lower: 0.1 μg/kg in muscles, 5.1–9.0 μg/kg in livers. Total PCBs levels were higher in cultivated sea bass than in wild fish; the concentration ranges were 5.3–59.7 μg/kg and 74.4–267.4 μg/kg in muscle and liver of reared samples, respectively, and 1.1–1.5 μg/kg and 63.2–109.4 μg/kg in muscle and liver of wild samples, respectively.     

Evaluation of A Sampling Strategy for Estimation of Long-term Pm2.5 Exposure for Epidemiological Studies

As part of the European Community Respiratory Health Survey (ECRHS) PM_2.5 (particles collected with an upper 50% cut point of 2.5 μm aerodynamic diameter) was measured using an EPA-WINS (Environmetal Protection Agency Well Impactor Ninety-six) sampler. The monitoring schedule was restricted to 7 days per month for one year. Simultaneously, during this one year study period a collocated Harvard Impactor (HI) was run on a daily basis in Erfurt, Germany. Here we validated the reliability of annual, seasonal and monthly means estimated using the ECRHS scheme (measurements taken less than 25% of the whole study period) with the ‘true’ long-term averages, which were estimated using all available daily means.The daily PM_2.5 means, obtained by both instruments operated in parallel, were only slightly different (the mean difference between EPA-WINS and HI was 1.8 μg m⁻³ and 2.8 μg m⁻³ for the winter means). The values obtained by the two instruments were highly correlated (r = 0.95).In view of that negligible difference, no additional bias was seen with respect to the annual and the winter means estimated by the two different sampling strategies (the difference was 1.7 μg m⁻³ and 2.7 μg m⁻³, respectively). Monthly means, however, can only be considered to be a crude estimate that may substantially under- or overestimate the true monthly mean value.     

Effects of Cadmium (CdCl2) on development and hatching of eggs in European squid (Loligo vulgaris Lamarck, 1798) (Cephalopoda: Loliginidae)

This is the first study related to the effects of cadmium (Cd) on the development and hatching of eggs of Loligo vulgaris. The eggs were exposed to concentrations varying from 10 to 100,000 μg Cd/l for up to 1 month. During the study period natural sea water salinity (37 PSU), ambient temperature (ranging 16.5–21.5°C) and light conditions of 12-h light: 12-h dark for 744-h were used prior to the hatching. For 96-h, mortality rate of 100% of the eggs was found at cadmium concentration of 100,000 μg Cd/l, and the same mortality rate of the eggs were found at 1,000 and 10,000 μg Cd/l for 744-h and 696-h, respectively. Hatching took place between hours 456 and 576 in the control group and between hours 480 and 576 in 10 and 100 μg Cd/l groups. Total hatching rates were calculated to be 98.2 ± 1.6% for control group, 99.4 ± 0.6% for 10 μg Cd/l group and 98.6 ± 1.2% for 100 μg Cd/l group. Hatching successes were estimated as 69.5 ± 13.8% for control group, 84.5 ± 8.2% for 10 μg Cd/l group and 76.9 ± 5.9% for 100 μg Cd/l group. In the 100,000 μg Cd/l treatment, the egg degeneration began from animal pole of the eggs in 16 h, and 50% and 100% of them died in the initial stage at 72-h and 96-h, respectively. In the 10,000 μg Cd/l group, the eggs which reached at stage 19 (IX) were deformed and 50% and 100% of them died at 312-h and 696-h, respectively. In 1,000 μg Cd/l group, however, the eggs developed abnormally from stage 21 (X–XI) and reached at stage 29 (XIX), and 50% and 100% of them died in 624-h and in 744-h, respectively. There were significant differences in survival rates of the eggs among the concentrations (p < 0.05). The current study demonstrated that Cd adversely affects the development, survival and hatching of L. vulgaris eggs; however, no mortality was observed in 10 μg Cd/l and 100 μg Cd/l groups.     

Health Risks Associated with Predicted Increase of Cadmium in Cultivated Soils and in the Diet

We have assessed the change of the dietary intake and the potential health risks of cadmium in Finland, assuming that a high level of cadmium in fertilizers (138 mg Cd/kg P) would prevail for the next 100 years. Soil measurements and modelling were used to derive the predicted level of cadmium in foods. In three important cultivars, wheat, potato and sugar beet, the cadmium concentration would increase by 20–35%. Consequently, the average dietary intake of cadmium in Finland would increase from 7.9 to 10.0 μg/day, corresponding with the urinary level of about 0.2 μg/l, a level that has not been associated with effects on the human health. However, in the risk group with 1) high dietary intake of cadmium, 2) elevated gastrointestinal absorption, and 3) tobacco smoking, the estimated urinary level of cadmium would be 2.0 μg/l. Recent epidemiological studies have shown that urinary level of 1–2 μg Cd/l is associated with an increased risk of bone demineralization and fractures, and 2–4 μg Cd/l with pre-clinical kidney damage. People characterized by more than one of the above-mentioned risks factors, may develop the adverse health effects at an old age, when cadmium has accumulated in the body.     

Organochlorine pesticides and polychlorinated biphenyls in common buzzard (<Emphasis Type="Italic">Buteo buteo</Emphasis>) from Sicily (Italy)

In the present study, we investigated the concentrations and distribution of organochlorine pesticides (OCs) and polychlorinated biphenyls (PCBs) in intestine, liver, and muscle samples of 11 common buzzards (Buteo buteo) from Sicily used as bioindicator for monitoring pollution in environment. All samples of common buzzards were collected at the “Recovery Center of Wild Fauna” of Palermo, through the Zooprophilactic Institute. Quantitative determination of OCs and PCBs in the samples examined has been carried out using HRGC-ECD and GC-MS. The results obtained show the presence of concentrations of ∑DDT and ∑PCB in almost all samples. Regarding ∑DDT (4,4^′-DDE, 2,4^′-DDD, 4,4^′-DDD, 2,4^′-DDT, and 4,4^′-DDT), the highest concentrations were found in intestine (0.411 ± 0.050 μg/g) followed by muscle (0.130 ± 0.017 μg/g) and liver samples (0.109 ± 0.014 μg/g). As regards the ∑PCB congeners (PCB-28, PCB-52, PCB-95, PCB-99, PCB-101, PCB-110, PCB-138, PCB-146, PCB-149, PCB-151, PCB-153, PCB-170, PCB-177, PCB-180, PCB-183, and PCB-187), the highest concentrations were found in intestine (1.686 ± 0.144 μg/g) followed by liver (1.064 ± 0.162 μg/g) and muscle samples (0.797 ± 0.078 μg/g). Our data deserve particular attention not only for their significance but especially because they were recorded in Sicily, a region with a very low risk of environmental pollution due to the shortage of industries.